When the rear window defogger switch on the air conditioning control assembly is pressed, the operation signal is transmitted to the air conditioning amplifier assembly via LIN communication. When the air conditioning amplifier assembly receives the signal, it turns on the defogger relay to operate the window defogger system.
Inspect the fuses for circuits related to this system before performing the following procedure.
Check the air conditioning system.
Both the window defogger system operation signal and air conditioning system operation signal are transmitted to the air conditioning amplifier assembly via the same communication line.
The air conditioning system operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Air Conditioner / Active Test.
According to the display on the GTS, perform the Active Test.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Defogger Relay (Rear) | Defogger relay | OFF, ON | - |
| Tester Display |
|---|
| Defogger Relay (Rear) |
The window defogger system operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the air conditioning amplifier assembly.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL
Check that the window defogger system operates normally.
The window defogger system operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the defogger relay.
Inspect the defogger relay.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Defogger Relay Holder |
Remove the defogger relay.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F75-1 - Body ground | Ignition switch ON | 11 to 14 V |
| F75-5 - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the defogger relay.
Disconnect the F3 air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F75-2 - F3-38 (RDFG) | Always | Below 1 Ω |
| F75-2 or F3-38 (RDFG) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Air Conditioning Amplifier Assembly) |
Reconnect the air conditioning amplifier assembly connector.
Reinstall the defogger relay.
Remove the air conditioning amplifier assembly with its connectors still connected.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F3-38 (RDFG) - F3-14 (GND) | Ignition switch ON, rear window defogger switch on | Below 1 V |
| F3-38 (RDFG) - F3-14 (GND) | Ignition switch ON, rear window defogger switch off | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for Sedan:
Disconnect the F60 and M1 back window glass connectors.
for Hatchback:
Disconnect the Q3 and R6 back door glass connectors.
Remove the F75 defogger relay.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F60-1 - F75-3 | Always | Below 1 Ω |
| M1-1 - Body ground | Always | Below 1 Ω |
| F60-1 - Body ground | Always | 10 kΩ or higher |
| F75-3 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Q3-1 - F75-3 | Always | Below 1 Ω |
| R6-1 - Body ground | Always | Below 1 Ω |
| Q3-1 - Body ground | Always | 10 kΩ or higher |
| F75-3 - Body ground | Always | 10 kΩ or higher |
| Result | Proceed to |
|---|---|
| OK (for Sedan) | A |
| OK (for Hatchback) | B |
| NG | C |
A
B
C