Home › Engine / Hybrid System › 1NZ-FE ENGINE CONTROL › SFI SYSTEM(w/ Air Fuel Ratio Sensor) › 2014.03–2016.07
RM30M0E _51 Engine / Hybrid System _017071 1NZ-FE ENGINE CONTROL _0116465 SFI SYSTEM(w/ Air Fuel Ratio Sensor) C

1NZ-FE ENGINE CONTROL  SFI SYSTEM(w/ Air Fuel Ratio Sensor)  P0351  Ignition Coil "A" Primary / Secondary Circuit  P0352  Ignition Coil "B" Primary / Secondary Circuit  P0353  Ignition Coil "C" Primary / Secondary Circuit  P0354  Ignition Coil "D" Primary / Secondary Circuit  


DESCRIPTION

HINT:
·

These DTCs indicate malfunctions relating to the primary circuit.

·

If DTC P0351 is output, check the No. 1 ignition coil (No. 1 cylinder) circuit.

·

If DTC P0352 is output, check the No. 1 ignition coil (No. 2 cylinder) circuit.

·

If DTC P0353 is output, check the No. 1 ignition coil (No. 3 cylinder) circuit.

·

If DTC P0354 is output, check the No. 1 ignition coil (No. 4 cylinder) circuit.



A Direct Ignition System (DIS) is used on this vehicle.

The direct ignition system is an ignition system in which each cylinder is ignited by its own ignition coil and spark plug. The secondary wiring of each ignition coil generates a powerful voltage which is applied directly to each spark plug. The spark passes from the center electrode of the spark plug to the ground electrode.

The ECM determines the ignition timing and transmits the ignition (IGT) signals to each cylinder. Using the IGT signal, the ECM turns the power transistor inside the igniter on and off. The power transistor, in turn, switches the current supplied to the primary coil on and off. When the current to the primary coil is cut off, a powerful voltage is generated in the secondary coil. This voltage is applied to the spark plugs, causing them to spark inside the cylinders. As the ECM cuts the current to the primary coil, the igniter sends back an ignition confirmation (IGF) signal to the ECM for each cylinder ignition.

A288665E07
5.417,0.552 5.75,0.417 false 4.333,0.365 4.531,0.781 true 0.469,0.875 2.26,1.073 1.792,0.198 10 false Crankshaft Position Sensor 0.448,2.677 2.24,2.875 1.792,0.198 10 false Camshaft Position Sensor 0.323,3.708 2.25,4.406 1.927,0.698 10 false Other Sensors (Engine Coolant Temperature Sensor, Mass Air Flow Meter, Throttle Position Sensor, etc.) 3.031,0.823 3.385,1 0.354,0.177 10 false IGT1 3.031,1.135 3.385,1.313 0.354,0.177 10 false IGF1 5.115,0.073 6.438,0.26 1.323,0.188 10 false from Battery 3.927,0.271 4.417,0.5 0.49,0.229 10 false Igniter 5.802,0.333 7.042,0.927 1.24,0.594 10 false No. 1 Ignition Coil (No. 1 Cylinder) 5.74,1.25 6.875,1.469 1.135,0.219 10 false No. 1 Spark Plug 5.74,2.469 6.875,2.688 1.135,0.219 10 false No. 2 Spark Plug 5.719,3.781 6.854,4 1.135,0.219 10 false No. 3 Spark Plug 5.75,5.104 6.885,5.323 1.135,0.219 10 false No. 4 Spark Plug 3,2.156 3.354,2.333 0.354,0.177 10 false IGT2 3,3.479 3.354,3.656 0.354,0.177 10 false IGT3 3.031,4.792 3.385,4.969 0.354,0.177 10 false IGT4 3.854,2.771 6.313,2.958 2.458,0.188 10 false No. 1 Ignition Coil (No. 2 Cylinder) 3.885,4.094 6.344,4.281 2.458,0.188 10 false No. 1 Ignition Coil (No. 3 Cylinder) 3.854,5.375 6.313,5.563 2.458,0.188 10 false No. 1 Ignition Coil (No. 4 Cylinder) 2.854,5.323 3.208,5.5 0.354,0.177 10 false ECM

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0351 Ignition Coil "A" Primary / Secondary Circuit No IGF signal to the ECM while the engine is running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF1 or IGT1 circuit between No. 1 ignition coil and ECM

·

No. 1 Ignition coil (No. 1 cylinder)

·

ECM


Comes on DTC stored
P0352 Ignition Coil "B" Primary / Secondary Circuit No IGF signal to the ECM while the engine is running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF1 or IGT2 circuit between No. 1 ignition coil and ECM

·

No. 1 ignition coil (No. 2 cylinder)

·

ECM


Comes on DTC stored
P0353 Ignition Coil "C" Primary / Secondary Circuit No IGF signal to the ECM while the engine is running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF1 or IGT3 circuit between No. 1 ignition coil and ECM

·

No. 1 ignition coil (No. 3 cylinder)

·

ECM


Comes on DTC stored
P0354 Ignition Coil "D" Primary / Secondary Circuit No IGF signal to the ECM while the engine is running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF1 or IGT4 circuit between No. 1 ignition coil and ECM

·

No. 1 ignition coil (No. 4 cylinder)

·

ECM


Comes on DTC stored

Reference: Inspection using an oscilloscope.

A285441E07
2.906,1 3.333,1.25 0.427,0.25 10 GND 2.896,1.615 3.292,1.833 0.396,0.219 10 GND 0.104,0.688 0.448,1.073 0.344,0.385 10 CH1 (IGT) 0.104,1.198 0.448,1.594 0.344,0.396 10 CH2 (IGF) 1.281,1.896 2.052,2.073 0.771,0.177 10 20 ms./DIV. 0.042,0.115 0.708,0.281 0.667,0.167 10 2 V/DIV.


While idling the engine, check the waveform between terminals IGT (1 to 4) and E1, and IGF1 and E1 of the ECM connector.

ECM Terminal Name CH1: Between IGT (1 to 4) and E1
CH2: Between IGF1 and E1
Tester Range 2 V/DIV., 20 ms./DIV.
Condition Idling


MONITOR DESCRIPTION

A212405E28
1.781,1.646 2.177,1.823 0.396,0.177 10 false ECM 2.958,1.302 3.229,1.49 0.271,0.188 10 false IGT 2.948,1.729 3.229,1.885 0.281,0.156 10 false IGF 4.156,1.51 4.594,1.656 0.438,0.146 10 false Igniter 5.396,1.344 6.167,1.521 0.771,0.177 10 false Ignition Coil 4.5,2.365 6.177,2.552 1.677,0.188 10 false No. 1 Ignition Coil 0.208,3.115 1.125,3.448 0.917,0.333 10 false Ignition Signal (IGT) 1.646,3.542 2.135,3.729 0.49,0.188 10 false Normal 1.385,3.948 2.156,4.135 0.771,0.188 10 false Malfunction 0.188,3.896 1.042,4.469 0.854,0.573 10 false Ignition Confirmation Signal (IGF) 3.635,4.51 4.875,4.719 1.24,0.208 10 false Circuit Malfunction 5.948,4.969 6.313,5.167 0.365,0.198 10 false Time

If the ECM does not receive any IGF signals despite transmitting the IGT signal, it interprets this as a fault in the igniter and stores a DTC.

MONITOR STRATEGY

Required Sensors/Components (Main) No. 1 ignition coil
Required Sensors/Components (Related) ECM
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine.

7.

Idle the engine for 10 seconds or more.

8.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P0351, P0352, P0353 or P0354.

12.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A320689E01
0.677,0.74 1.135,0.938 0.458,0.198 10 false AM2 0.5,0.74 0.958,0.938 0.458,0.198 10 false 5 1.51,0.74 1.969,0.938 0.458,0.198 10 false IG2 1.813,0.74 2.271,0.938 0.458,0.198 10 false 6 2.333,0.969 3.042,1.188 0.708,0.219 10 false IG2 NO.1 3.781,0.729 4.24,0.927 0.458,0.198 10 false 1 3.948,0.823 4.406,1.021 0.458,0.198 10 false +B 3.948,1.125 4.406,1.323 0.458,0.198 10 false GND 3.792,1.052 4.25,1.25 0.458,0.198 10 false 4 4.969,0.729 5.427,0.927 0.458,0.198 10 false 3 4.969,1.031 5.427,1.229 0.458,0.198 10 false 2 4.583,0.844 5.042,1.042 0.458,0.198 10 false IGT1 4.656,1.146 5.115,1.344 0.458,0.198 10 false IGF 5.865,0.729 6.323,0.927 0.458,0.198 10 false 17 6.104,0.833 6.563,1.031 0.458,0.198 10 false IGT1 6.104,2.427 6.563,2.625 0.458,0.198 10 false IGT2 5.865,2.333 6.323,2.531 0.458,0.198 10 false 16 6.104,4.031 6.563,4.229 0.458,0.198 10 false IGT3 5.865,3.927 6.323,4.125 0.458,0.198 10 false 15 6.104,5.542 6.563,5.74 0.458,0.198 10 false IGT4 5.875,5.438 6.333,5.635 0.458,0.198 10 false 14 5.875,5.854 6.333,6.052 0.458,0.198 10 false 23 6.104,5.948 6.563,6.146 0.458,0.198 10 false IGF1 3.896,1.542 5.01,1.938 1.115,0.396 10 false No. 1 Ignition Coil (No. 1 Cylinder) 3.896,1.385 4.354,1.583 0.458,0.198 10 false B11 3.781,2.354 4.24,2.552 0.458,0.198 10 false 1 3.781,2.667 4.24,2.865 0.458,0.198 10 false 4 4.969,2.344 5.427,2.542 0.458,0.198 10 false 3 4.969,2.656 5.427,2.854 0.458,0.198 10 false 2 3.948,2.448 4.406,2.646 0.458,0.198 10 false +B 3.948,2.74 4.406,2.938 0.458,0.198 10 false GND 4.594,2.448 5.052,2.646 0.458,0.198 10 false IGT2 4.667,2.75 5.125,2.948 0.458,0.198 10 false IGF 4.594,4.052 5.052,4.25 0.458,0.198 10 false IGT3 4.969,4.24 5.427,4.438 0.458,0.198 10 false 2 4.969,3.927 5.427,4.125 0.458,0.198 10 false 3 4.667,4.344 5.125,4.542 0.458,0.198 10 false IGF 3.948,4.333 4.406,4.531 0.458,0.198 10 false GND 3.948,4.031 4.406,4.229 0.458,0.198 10 false +B 3.781,5.854 4.24,6.052 0.458,0.198 10 false 4 3.771,5.438 4.229,5.635 0.458,0.198 10 false 1 3.906,2.99 4.365,3.188 0.458,0.198 10 false B12 3.906,3.146 5.021,3.542 1.115,0.396 10 false No. 1 Ignition Coil (No. 2 Cylinder) 3.896,4.625 4.354,4.823 0.458,0.198 10 false B13 3.906,4.771 5.021,5.167 1.115,0.396 10 false No. 1 Ignition Coil (No. 3 Cylinder) 3.896,6.198 4.354,6.396 0.458,0.198 10 false B14 3.896,6.344 5.01,6.74 1.115,0.396 10 false No. 1 Ignition Coil (No. 4 Cylinder) 4.573,5.552 5.031,5.75 0.458,0.198 10 false IGT4 4.646,5.969 5.104,6.167 0.458,0.198 10 false IGF 4.969,5.854 5.427,6.052 0.458,0.198 10 false 2 4.969,5.448 5.427,5.646 0.458,0.198 10 false 3 3.792,4.25 4.25,4.448 0.458,0.198 10 false 4 3.781,3.938 4.24,4.135 0.458,0.198 10 false 1 3.948,5.542 4.406,5.74 0.458,0.198 10 false +B 3.948,5.948 4.406,6.146 0.458,0.198 10 false GND 6.417,7.208 6.875,7.406 0.458,0.198 10 false B29 0.51,4.958 1.156,5.177 0.646,0.219 10 false Battery 6.417,7.354 6.875,7.552 0.458,0.198 10 false ECM 0.354,4.323 1,4.542 0.646,0.219 10 false FL MAIN 0.354,3.708 1,3.927 0.646,0.219 10 false MAIN 0.354,3.052 1,3.271 0.646,0.219 10 false AM2 0.458,1.104 0.917,1.302 0.458,0.198 10 false F7 0.469,1.24 2.021,1.646 1.552,0.406 10 false Ignition or Starter Switch Assembly

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NO. 1 IGNITION COIL - BODY GROUND)
a.

Disconnect the B11, B12, B13 and B14 No. 1 ignition coil connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B11-4 (GND) - Body ground Always Below 1 Ω
B12-4 (GND) - Body ground Always Below 1 Ω
B13-4 (GND) - Body ground Always Below 1 Ω
B14-4 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF NO. 1 IGNITION COIL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF NO. 1 IGNITION COIL)
a.
A200905C06
0.333,0.469 0.792,0.74 0.458,0.271 0.333,0.792 0.792,1.063 0.458,0.271 0.333,1.115 0.792,1.385 0.458,0.271 0.333,1.438 0.792,1.708 0.458,0.271 2.115,1.177 2.521,1.708 true 1.333,1.177 1.073,1.688 true 0.146,0.083 0.406,0.26 0.26,0.177 10 false *a 0.417,0.521 0.719,0.698 0.302,0.177 10 false B11 0.417,0.844 0.719,1.021 0.302,0.177 10 false B12 0.417,1.167 0.719,1.344 0.302,0.177 10 false B13 0.417,1.49 0.719,1.667 0.302,0.177 10 false B14 2.406,1.719 2.76,1.885 0.354,0.167 10 false GND 0.938,1.719 1.167,1.885 0.229,0.167 10 false +B
*a Front view of wire harness connector
(to No. 1 ignition coil)


Disconnect the No. 1 ignition coil connectors.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B11-1 (+B) - B11-4 (GND) Ignition switch ON 11 to 14 V
B12-1 (+B) - B12-4 (GND) Ignition switch ON 11 to 14 V
B13-1 (+B) - B13-4 (GND) Ignition switch ON 11 to 14 V
B14-1 (+B) - B14-4 (GND) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (NO. 1 IGNITION COIL - ECM)

NG

5.CHECK HARNESS AND CONNECTOR (NO. 1 IGNITION COIL - IGNITION OR STARTER SWITCH ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (NO. 1 IGNITION COIL - ECM)
a.

Disconnect the B11, B12, B13 and B14 No. 1 ignition coil connectors.


b.

Disconnect the B29 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B11-2 (IGF) - B29-23 (IGF1) Always Below 1 Ω
B12-2 (IGF) - B29-23 (IGF1) Always Below 1 Ω
B13-2 (IGF) - B29-23 (IGF1) Always Below 1 Ω
B14-2 (IGF) - B29-23 (IGF1) Always Below 1 Ω
B11-3 (IGT1) - B29-17 (IGT1) Always Below 1 Ω
B12-3 (IGT2) - B29-16 (IGT2) Always Below 1 Ω
B13-3 (IGT3) - B29-15 (IGT3) Always Below 1 Ω
B14-3 (IGT4) - B29-14 (IGT4) Always Below 1 Ω
B11-2 (IGF) or B29-23 (IGF1) - Body ground Always 10 kΩ or higher
B12-2 (IGF) or B29-23 (IGF1) - Body ground Always 10 kΩ or higher
B13-2 (IGF) or B29-23 (IGF1) - Body ground Always 10 kΩ or higher
B14-2 (IGF) or B29-23 (IGF1) - Body ground Always 10 kΩ or higher
B11-3 (IGT1) or B29-17 (IGT1) - Body ground Always 10 kΩ or higher
B12-3 (IGT2) or B29-16 (IGT2) - Body ground Always 10 kΩ or higher
B13-3 (IGT3) or B29-15 (IGT3) - Body ground Always 10 kΩ or higher
B14-3 (IGT4) or B29-14 (IGT4) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0351, P0352, P0353 OR P0354)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0351, P0352, P0353 OR P0354)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>1NZ-FE ENGINE CONTROL>SFI SYSTEM(w/ Air Fuel Ratio Sensor)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Shuffle the arrangement of the ignition coil assemblies (among No. 1 to No. 4 cylinders).

NOTICE:

Do not change the location of the connectors.



f.

Perform a simulation test.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


h.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234

Result:
Result Proceed to
Same DTC output A
Different ignition coil DTC output B



A

B

5.CHECK HARNESS AND CONNECTOR (NO. 1 IGNITION COIL - IGNITION OR STARTER SWITCH ASSEMBLY)
a.

Disconnect the B11, B12, B13 and B14 No. 1 ignition coil connectors.


b.

Disconnect the F7 ignition or starter switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B11-1 (+B) - F7-6 (IG2) Always Below 1 Ω
B12-1 (+B) - F7-6 (IG2) Always Below 1 Ω
B13-1 (+B) - F7-6 (IG2) Always Below 1 Ω
B14-1 (+B) - F7-6 (IG2) Always Below 1 Ω
B11-1 (+B) or F7-6 (IG2) - Body ground Always 10 kΩ or higher
B12-1 (+B) or F7-6 (IG2) - Body ground Always 10 kΩ or higher
B13-1 (+B) or F7-6 (IG2) - Body ground Always 10 kΩ or higher
B14-1 (+B) or F7-6 (IG2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR