Home › Engine / Hybrid System › 1NZ-FE ENGINE CONTROL › SFI SYSTEM(w/ Air Fuel Ratio Sensor) › 2014.03–2016.07
RM30M0E _51 Engine / Hybrid System _017071 1NZ-FE ENGINE CONTROL _0116465 SFI SYSTEM(w/ Air Fuel Ratio Sensor) C

1NZ-FE ENGINE CONTROL  SFI SYSTEM(w/ Air Fuel Ratio Sensor)  P0617  Starter Relay Circuit High  


DESCRIPTION

While the engine is being cranked, the battery voltage is applied to terminal STA of the ECM.

If the ECM detects the starter signal (STA signal) while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores the DTC.

This monitor runs when the vehicle is driven at 20 km/h (12.4 mph) for 20 seconds.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0617 Starter Relay Circuit High Following conditions (a), (b) and (c) met for 20 seconds (1 trip detection logic):

(a) Vehicle speed 20 km/h (12.4 mph) or more

(b) Engine speed 1000 rpm or more

(c) STA signal ON


·

Park/neutral position switch*1

·

Clutch start switch assembly*2

·

Starter relay assembly circuit

·

Ignition or start switch assembly

·

ECM


Comes on DTC stored

*1: for Automatic Transaxle

*2: for Manual Transaxle


MONITOR DESCRIPTION

Required Sensors/Components (Main) Starter relay assembly
Park/neutral position switch*1
Clutch start switch assembly*2
Ignition or starter switch assembly
Required Sensors/Components (Related) Vehicle speed sensor
Crankshaft position sensor
Frequency of Operation Continuous

*1: for Automatic Transaxle

*2: for Manual Transaxle


TYPICAL ENABLING CONDITIONS

Vehicle speed 20 km/h (12.4 mph) or more
Engine speed 1000 rpm or more

TYPICAL MALFUNCTION THRESHOLDS

Starter signal ON

CONFIRMATION DRIVING PATTERN

A231469E15
1.229,1.979 1.604,2.156 0.375,0.177 10 false Idling 0.396,2.25 1.604,2.573 1.208,0.323 10 false Ignition Switch ON 0.354,0.813 1.667,0.99 1.313,0.177 10 false 20 km/h (12.4 mph) 2.396,2.854 3.083,3.167 0.688,0.313 10 false 5 seconds or more 3.594,2.938 4.865,3.104 1.271,0.167 10 false 20 seconds or more 2,2.333 2.25,2.521 0.25,0.188 10 false [A] 2.583,2.125 2.792,2.302 0.208,0.177 10 false [B] 4.031,0.458 4.26,0.625 0.229,0.167 10 false [C] 4.906,3.344 5.135,3.51 0.229,0.167 10 false [D]

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on [A].

6.

Idle the engine for 5 seconds or more [B].

7.

Drive the vehicle at 20 km/h (12.4 mph) or more for 20 seconds or more [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


8.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P0617.

12.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [C] and [D] again and, if necessary, extend the driving time.




WIRING DIAGRAM

A321939E02
1.031,0.729 1.229,0.948 0.198,0.219 10 false 5 2.302,0.729 2.5,0.948 0.198,0.219 10 false 7 1.208,0.729 1.604,0.958 0.396,0.229 10 false AM2 1.969,0.729 2.427,0.927 0.458,0.198 10 false ST2 0.938,1.073 1.25,1.271 0.313,0.198 10 false F7 0.948,1.208 2.458,1.594 1.51,0.385 10 false Ignition or Starter Switch Assembly 0.417,1.552 0.813,1.781 0.396,0.229 10 false AM2 0.438,2.417 1.115,2.677 0.677,0.26 10 false MAIN 3.969,0.958 4.427,1.156 0.458,0.198 10 false STA 3.406,1.469 3.698,1.75 0.292,0.281 10 false 1 4.677,1.469 4.969,1.75 0.292,0.281 10 false 2 3.469,1.823 3.927,2.021 0.458,0.198 10 false A28 3.469,1.969 4.667,2.396 1.198,0.427 10 false Clutch Start Switch Assembly*1 4.875,1.469 5.167,1.75 0.292,0.281 10 false *1 5.49,0.625 5.781,0.906 0.292,0.281 10 false 9 5.427,0.813 5.74,1.01 0.313,0.198 10 false F82 5.417,3.26 5.729,3.458 0.313,0.198 10 false B31 5.417,3.74 5.729,3.938 0.313,0.198 10 false B31 5.417,4.208 5.729,4.406 0.313,0.198 10 false B31 5.417,4.677 5.729,4.875 0.313,0.198 10 false B31 5.417,5.167 5.729,5.365 0.313,0.198 10 false B31 5.406,5.635 5.719,5.833 0.313,0.198 10 false B31 5.417,6.469 5.729,6.667 0.313,0.198 10 false F82 5.469,3.052 5.76,3.333 0.292,0.281 10 false 34 5.469,3.542 5.76,3.823 0.292,0.281 10 false 17 5.458,4.021 5.75,4.302 0.292,0.281 10 false 26 5.469,4.49 5.76,4.771 0.292,0.281 10 false 21 5.458,4.979 5.75,5.26 0.292,0.281 10 false 18 5.458,5.438 5.75,5.719 0.292,0.281 10 false 16 5.458,6.271 5.75,6.552 0.292,0.281 10 false 19 5.771,0.823 6.417,1.042 0.646,0.219 10 false NSW 5.781,3.271 6.177,3.563 0.396,0.292 10 false P 5.781,3.729 6.177,4.021 0.396,0.292 10 false R 5.781,4.208 6.177,4.5 0.396,0.292 10 false N 5.771,4.677 6.167,4.969 0.396,0.292 10 false D 5.771,5.177 6.167,5.469 0.396,0.292 10 false 2 5.771,5.635 6.167,5.927 0.396,0.292 10 false L 5.771,6.365 6.229,6.563 0.458,0.198 10 false STA 6.188,7.396 6.865,7.656 0.677,0.26 10 false ECM 3.198,5.906 3.563,6.198 0.365,0.292 10 false B19 3.198,6.073 5.281,6.417 2.083,0.344 10 false Park/Neutral Position Switch*2 3.094,2.177 3.385,2.458 0.292,0.281 10 false *1 3.135,2.688 3.427,2.969 0.292,0.281 10 false *2 3.406,2.688 3.698,2.969 0.292,0.281 10 false 5 3.625,2.688 3.917,2.969 0.292,0.281 10 false L 4.479,2.688 4.771,2.969 0.292,0.281 10 false B 4.677,2.688 4.969,2.969 0.292,0.281 10 false 4 4.688,3.167 4.979,3.448 0.292,0.281 10 false 6 4.677,3.635 4.969,3.917 0.292,0.281 10 false 1 4.677,4.104 4.969,4.385 0.292,0.281 10 false 9 4.688,4.594 4.979,4.875 0.292,0.281 10 false 7 4.688,5.073 4.979,5.354 0.292,0.281 10 false 3 4.688,5.542 4.979,5.823 0.292,0.281 10 false 8 4.406,3.156 4.698,3.438 0.292,0.281 10 false PL 4.406,3.635 4.698,3.917 0.292,0.281 10 false RL 4.406,4.104 4.698,4.385 0.292,0.281 10 false NL 4.406,4.583 4.698,4.865 0.292,0.281 10 false DL 4.406,5.052 4.698,5.333 0.292,0.281 10 false 2L 4.417,5.542 4.708,5.823 0.292,0.281 10 false LL 3.115,4.344 3.406,4.625 0.292,0.281 10 false *2 3.396,4.344 3.688,4.625 0.292,0.281 10 false 2 5.073,3.156 5.365,3.438 0.292,0.281 10 false *2 5.073,3.635 5.365,3.917 0.292,0.281 10 false *2 5.073,4.104 5.365,4.385 0.292,0.281 10 false *2 5.073,4.594 5.365,4.875 0.292,0.281 10 false *2 5.063,5.073 5.354,5.354 0.292,0.281 10 false *2 5.052,5.542 5.344,5.823 0.292,0.281 10 false *2 5.115,2.167 5.406,2.448 0.292,0.281 10 false *2 0.844,3.292 1.135,3.573 0.292,0.281 10 false ST 0.448,4.219 1.521,4.417 1.073,0.198 10 false FL MAIN 1.417,3.417 1.708,3.698 0.292,0.281 10 false 5 1.885,3.417 2.177,3.698 0.292,0.281 10 false 2 1.875,4.323 2.167,4.604 0.292,0.281 10 false 1 1.427,4.323 1.719,4.604 0.292,0.281 10 false 3 1.427,4.927 1.792,5.219 0.365,0.292 10 false B15 1.188,4.969 1.479,5.25 0.292,0.281 10 false 1 0.677,5.188 0.99,5.385 0.313,0.198 10 false B28 0.771,4.99 1.063,5.271 0.292,0.281 10 false 1 2.115,3.771 2.938,4.198 0.823,0.427 10 false Starter Relay Assembly 2.031,4.448 2.844,4.823 0.813,0.375 10 false from ECU-IG NO. 3 fuse 2.083,5.365 2.813,5.833 0.729,0.469 10 false Starter Assembly 0.604,6.688 1.677,6.885 1.073,0.198 10 false Battery 2.469,6.844 4.323,7.104 1.854,0.26 10 false *1: for Manual Transaxle 2.479,7.198 4.333,7.458 1.854,0.26 10 false *2: for Automatic Transaxle 3.583,4.344 3.875,4.625 0.292,0.281 10 false RB

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:
·

The following troubleshooting flowchart is based on the premise that the engine is cranked normally.

If the engine will not crank, proceed to the Problem Symptoms Table.

Click hereEngine / Hybrid System>1NZ-FE ENGINE CONTROL>SFI SYSTEM(w/ Air Fuel Ratio Sensor)>PROBLEM SYMPTOMS TABLE

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.

Powertrain > Engine and ECT > Data List
Tester Display
Starter Signal
50003 234 118

e.

Check the value displayed on the GTS when the vehicle is driven at 20 km/h (12.4 mph) or more.

NOTICE:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.



Result:
Condition GTS Display Proceed to
Driving at 20 km/h (12.4 mph) or more OFF A
ON (for Automatic Transaxle) B
ON (for Manual Transaxle) C



A

B

2.READ VALUE USING GTS (STARTER SIGNAL)

C

8.READ VALUE USING GTS (STARTER SIGNAL)
2.READ VALUE USING GTS (STARTER SIGNAL)
a.

Disconnect the B19 park/neutral position switch connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.

Powertrain > Engine and ECT > Data List
Tester Display
Starter Signal
50003 234 118

f.

Read the value displayed on the GTS when the ignition switch is ON.


Result:
Result Proceed to
ON A
OFF B



A

3.INSPECT ECM (STA TERMINAL VOLTAGE)

B

4.INSPECT PARK/NEUTRAL POSITION SWITCH
3.INSPECT ECM (STA TERMINAL VOLTAGE)
a.
A301477C03
1.656,1.594 2.063,1.813 0.406,0.219 2.323,2.875 1.958,2.198 true 0.198,0.125 0.51,0.323 0.313,0.198 10 false *a 1.74,1.615 2.198,1.813 0.458,0.198 10 false F82 2.167,2.896 2.625,3.094 0.458,0.198 10 false STA
*a Rear view of wire harness connector
(to ECM)


Disconnect the B19 park/neutral position switch connector.


b.

Disconnect the ECM connector.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.


Result:
Tester Connection Switch Condition Specified Condition Proceed to
F82-19 (STA) - Body ground Ignition switch ON 11 to 14 V A
Below 1.5 V B



A

REPAIR OR REPLACE HARNESS OR CONNECTOR (STARTER RELAY ASSEMBLY - PARK/NEUTRAL POSITION SWITCH - ECM)

B

4.INSPECT PARK/NEUTRAL POSITION SWITCH
a.
C193931C17
1.615,0.969 2,0.333 true 1.146,0.969 0.75,0.583 true 2.75,1.75 2.354,1.5 true 0.083,0.073 0.417,0.417 0.333,0.344 10 *a 0.583,0.469 0.74,0.667 0.156,0.198 10 B 2.792,1.719 3.042,1.969 0.25,0.25 10 L 2.042,0.229 2.281,0.479 0.24,0.25 10 RB
*a Component without harness connected
(Park/Neutral Position Switch)


Disconnect the B19 park/neutral position switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
4 (B) - 5 (L) Always 10 kΩ or higher
2 (RB) - 5 (L) Always 10 kΩ or higher



Result:
Result Proceed to
Outside standard range
(Tester Connection 4(B) - 5(L))
A
Outside standard range
(Tester Connection 2(RB) - 5(L))
B
Within standard range C



A

5.REPLACE PARK/NEUTRAL POSITION SWITCH

B

C

6.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
5.REPLACE PARK/NEUTRAL POSITION SWITCH

Result:
Proceed to
NEXT



NEXT

6.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
6.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
a.

Inspect the ignition or starter switch assembly.

Click hereEngine / Hybrid System>1NZ-FE STARTING>IGNITION SWITCH>INSPECTION


Result:
Result
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM - IGNITION OR STARTER SWITCH ASSEMBLY)

NG

REPLACE IGNITION OR STARTER SWITCH ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM - IGNITION OR STARTER SWITCH ASSEMBLY)
a.

Disconnect the B19 park/neutral position switch connector.


b.

Disconnect the F82 ECM connector.


c.

Disconnect the F7 ignition or starter switch assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B19-4 (B), F82-9 (NSW) or F7-7 (ST2) - Body ground Always 10 kΩ or higher



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.READ VALUE USING GTS (STARTER SIGNAL)
a.

Disconnect the A28 clutch start switch assembly connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.

Powertrain > Engine and ECT > Data List
Tester Display
Starter Signal
50003 234 118

f.

Read the value displayed on the GTS when the ignition switch is ON.


Result:
Result Proceed to
ON A
OFF B



A

9.INSPECT ECM (STA TERMINAL VOLTAGE)

B

10.INSPECT CLUTCH START SWITCH ASSEMBLY
9.INSPECT ECM (STA TERMINAL VOLTAGE)
a.
A301477C03
1.656,1.594 2.063,1.813 0.406,0.219 2.323,2.875 1.958,2.198 true 0.198,0.125 0.51,0.323 0.313,0.198 10 false *a 1.74,1.615 2.198,1.813 0.458,0.198 10 false F82 2.167,2.896 2.625,3.094 0.458,0.198 10 false STA
*a Rear view of wire harness connector
(to ECM)


Disconnect the A28 clutch start switch assembly connector.


b.

Disconnect the ECM connector.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.


Result:
Tester Connection Switch Condition Specified Condition Proceed to
F82-19 (STA) - Body ground Ignition switch ON 11 to 14 V A
Below 1.5 V B



A

REPAIR OR REPLACE HARNESS OR CONNECTOR (STARTER RELAY ASSEMBLY - CLUTCH START SWITCH ASSEMBLY - ECM)

B

10.INSPECT CLUTCH START SWITCH ASSEMBLY
a.

Inspect the clutch start switch assembly.

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION


Result:
Result Proceed to
NG A
OK B



A

11.REPLACE CLUTCH START SWITCH ASSEMBLY

B

12.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
11.REPLACE CLUTCH START SWITCH ASSEMBLY
a.

Replace the clutch start switch assembly.

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>REMOVAL


Result:
Proceed to
NEXT



NEXT

12.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
12.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
a.

Inspect the ignition or starter switch assembly.

Click hereEngine / Hybrid System>1NZ-FE STARTING>IGNITION SWITCH>INSPECTION


Result:
Result
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH ASSEMBLY - ECM - IGNITION OR STARTER SWITCH ASSEMBLY)

NG

REPLACE IGNITION OR STARTER SWITCH ASSEMBLY

13.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH ASSEMBLY - ECM - IGNITION OR STARTER SWITCH ASSEMBLY)
a.

Disconnect the A28 clutch start switch assembly connector.


b.

Disconnect the F82 ECM connector.


c.

Disconnect the F7 ignition or starter switch assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A28-2, F82-9 (NSW) or F7-7 (ST2) - Body ground Always 10 kΩ or higher



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR