Home › Engine / Hybrid System › 2NZ-FE FUEL › FUEL TANK(for TMT Made) › 2014.03–2016.07
RM30M0E _51 Engine / Hybrid System _017076 2NZ-FE FUEL _0092331 FUEL TANK(for TMT Made) A

2NZ-FE FUEL  FUEL TANK(for TMT Made)  INSTALLATION  


PROCEDURE

Hide 77218A 1.INSTALL NO. 3 FUEL TANK FILLER PIPE SUPPORT

a.
A311728C01
0.719,0.281 1.031,0.479 0.313,0.198 10 false *a
*a Cutaway View
V100136

Front of Vehicle


Engage the clamp to install the No. 3 fuel tank filler pipe support to the fuel tank filler pipe assembly.


Hide 77216A 2.INSTALL NO. 1 FUEL TANK FILLER PIPE SUPPORT

a.
A311729C01
0.385,2.188 0.698,2.385 0.313,0.198 10 false *a
*a Cutaway View
V100136

Left Side of Vehicle


Install the No. 1 fuel tank filler pipe support to the fuel tank filler pipe assembly.


Hide 77217C 3.INSTALL NO. 2 FUEL TANK FILLER PIPE SUPPORT

a.
A311730C01
0.583,2.167 0.896,2.365 0.313,0.198 10 false *a
*a Cutaway View
V100136

Left Side of Vehicle


Engage the clamp to install the No. 2 fuel tank filler pipe support to the fuel tank filler pipe assembly.


Hide 77701W 4.INSTALL NO. 1 CANISTER OUTLET HOSE SUB-ASSEMBLY

a.

Connect the No. 1 canister outlet hose sub-assembly to the No. 6 fuel tank breather tube.


b.

Engage the 2 clamps to install the No. 1 canister outlet hose sub-assembly to the fuel tank assembly.


Hide 77028F 5.INSTALL NO. 2 FUEL EMISSION TUBE SUB-ASSEMBLY

a.

Engage the 2 clamps to install the No. 2 fuel emission tube sub-assembly to the fuel tank assembly.


Hide 77209F 6.INSTALL FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.

Engage the 2 clamps to install the fuel tank main tube sub-assembly to the fuel tank assembly.


Hide 77100 7.INSTALL FUEL TANK ASSEMBLY

a.

Clean and degrease the bolt holes.


b.

Using an engine lifter, set the fuel tank assembly.


c.

Install the fuel tank assembly to the vehicle with 4 new bolts.

Torque:
14.3 N*m (146 kgf*cm, 11 ft.*lbf)


d.
A247509C02
1.458,0.323 1.677,0.188 true 0.292,0.615 1.052,0.823 true 0.115,0.521 0.427,0.677 0.313,0.156 10 false *1 1.677,0.063 1.833,0.219 0.156,0.156 10 true *2
*1 Fuel Tank Filler Pipe Sub-assembly
*2 No. 1 Fuel Tank Breather Tube


Connect the fuel tank filler pipe sub-assembly and No. 1 fuel tank breather tube to the No. 3 fuel tank filler pipe support.


e.
A305589

Engage the clamp to install the fuel tank filler pipe flange plate to the No. 3 fuel tank filler pipe support.


f.

Install the fuel tank filler pipe flange plate to the vehicle with the bolt.

Torque:
34 N*m (347 kgf*cm, 25 ft.*lbf)


g.

Engage the 2 clamps to connect the No. 6 fuel tank breather tube.

HINT:
A302966C02
1.563,0.708 1.75,0.469 true 0.385,1.479 0.573,1.24 false 2.802,1.51 2.813,1.188 true 0.885,1.198 1.917,1.75 1.917,1.75 2.427,1.188 true 1.792,0.365 2.104,0.521 0.313,0.156 10 true *1 0.198,1.396 0.51,1.552 0.313,0.156 10 false *a 1.865,1.792 2.177,1.948 0.313,0.156 10 false *b 2.729,1.563 3.031,1.823 0.302,0.26 10 true *a
*1 No. 6 Fuel Tank Breather Tube
*a Clamp
*b Rib


Install the No. 6 fuel tank breather tube so that its 2 ribs are between the 2 clamps as shown in the illustration.



Hide 77209F 8.CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.
A302962C01
2.063,2.333 2.24,2.313 false 2.323,2.198 2.635,2.354 0.313,0.156 10 false *1
*1 Retainer
V100135

Push


Line up the fuel main tube and fuel tube connector, and push them together until a "click" sound is heard. If the fuel main tube is difficult to push into the fuel tube connector, apply a small amount of clean engine oil to the tip of the fuel main tube and reinsert it.


b.

Push down the retainer.

NOTICE:
·

Check that there is no damage or foreign matter around the connecting parts of the fuel tube connector and fuel main tube before starting this step.

·

After connecting the fuel tube connector, check that it is securely connected by pulling on it.




Hide 77028F 9.CONNECT NO. 2 FUEL EMISSION TUBE SUB-ASSEMBLY

a.

Connect the No. 2 fuel emission tube sub-assembly to the fuel tank to canister tube with the hose clip.


Hide 46420 10.CONNECT NO. 2 PARKING BRAKE CABLE ASSEMBLY

a.

Connect the No. 2 parking brake cable assembly to the vehicle with the 2 bolts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


Hide 77641A 11.INSTALL NO. 1 FUEL TANK PROTECTOR

a.

Install the No. 1 fuel tank protector to the vehicle with the bolt and clip.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 58156 12.INSTALL NO. 4 FRONT FLOOR HEAT INSULATOR

a.
A300030E01
2.813,1.927 2.969,2.125 0.156,0.198 10 false A 1.333,0.958 1.49,1.156 0.156,0.198 10 false B

Install the No. 4 front floor heat insulator to the vehicle with the 2 nuts.

Torque:
Nut A : 5.4 N*m (55 kgf*cm, 48 in.*lbf)

Torque:
Nut B : 5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 17410 13.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 57533B 14.INSTALL FRONT FLOOR CENTER BRACE

Hide 58910C 15.INSTALL REAR CONSOLE BOX ASSEMBLY (w/ Console Box Lid)

Hide 58910C 16.INSTALL REAR CONSOLE BOX ASSEMBLY (w/o Console Box Lid)

Hide 17.INSTALL REAR WHEEL LH

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)

Hide 77020A 18.INSTALL FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

Hide 19.ADD FUEL

Hide 77310A 20.INSTALL FUEL TANK CAP ASSEMBLY

Hide 22.INSPECT EXHAUST GAS LEAK