Home › Brake › BRAKE (REAR) › REAR BRAKE(for Disc Type) › 2014.03–2017.10
RM30M0E _54 Brake _017101 BRAKE (REAR) _0092768 REAR BRAKE(for Disc Type) A

BRAKE (REAR)  REAR BRAKE(for Disc Type)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the LH side and RH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 42431 1.INSTALL REAR DISC

a.
C283238C01
1.927,0.906 2.906,0.792 2.906,0.792 1.958,0.969 true 2.938,0.698 3.25,0.854 0.313,0.156 10 false *a
*a Matchmark


Align the matchmarks on the rear disc and rear axle hub and bearing assembly, and install the rear disc.

NOTICE:

When replacing the rear disc with a new one, select the installation position where the rear disc has minimal runout.



Hide 47822 2.INSTALL REAR DISC BRAKE CYLINDER MOUNTING

a.

Install the rear disc brake cylinder mounting to the rear axle beam assembly with the 2 bolts.

Torque:
57.4 N*m (585 kgf*cm, 42 ft.*lbf)


Hide 47875R 3.INSTALL REAR DISC BRAKE BUSH DUST BOOT

a.
C224880C02
1.938,0.823 2.104,0.823 false
V100155

Lithium Soap Base Glycol Grease


Apply a light layer of lithium soap base glycol grease to the entire circumference of 2 new rear disc brake bush dust boots.

HINT:

Apply at least 0.3 g (0.01 oz.) of lithium soap base glycol grease to each rear disc brake bush dust boot.



b.

Install the 2 rear disc brake bush dust boots to the rear disc brake cylinder mounting.


Hide 47835 4.INSTALL REAR DISC BRAKE PAD GUIDE PIN

a.
C211757C04
1.76,1.156 1.75,1.156 false
V100155

Lithium Soap Base Glycol Grease


Apply a light layer of lithium soap base glycol grease to the contact surface of the 2 rear disc brake pad guide pins.


b.

Install a new rear disc brake cylinder slide bush to each rear disc brake pad guide pin.


c.
C211758C04
1.25,0.938 1.25,0.927 false
V100155

Lithium Soap Base Glycol Grease


Apply a light layer of lithium soap base glycol grease to the sliding part and sealing surfaces of the 2 rear disc brake pad guide pins.


d.

Install the 2 rear disc brake pad guide pins to the rear disc brake cylinder mounting.


e.

Push the 2 rear disc brake pad guide pins into the 2 rear disc brake bush dust boots to engage the 2 rear disc brake pad guide pins to the rear disc brake bush dust boot.


Hide 04948 5.INSTALL REAR DISC BRAKE FITTING KIT

a.
C282423C01
0.24,0.573 0.667,0.573 false 0.24,1.385 0.469,1.385 false 0.073,1.292 0.385,1.448 0.313,0.156 10 false *1 0.073,0.469 0.385,0.625 0.313,0.156 10 false *2
*1 Rear No. 1 Disc Brake Pad Support Plate
*2 Rear No. 2 Disc Brake Pad Support Plate


Install the rear No. 1 disc brake pad support plate and rear No. 2 disc brake pad support plate to the rear disc brake cylinder mounting.

NOTICE:

Be sure to install each rear disc brake pad support plate in the correct position and direction.



Hide 04946 6.INSTALL REAR DISC BRAKE ANTI SQUEAL SHIM KIT

a.
C275018C02
0.76,0.313 1.073,0.469 0.313,0.156 10 false *a 0.76,1.792 1.073,1.948 0.313,0.156 10 false *b
*a Inner
*b Outer
V100145

Disc Brake Grease


Apply disc brake grease to the back plate of the rear disc brake pads.


b.
C275019C02
0.417,1.313 0.417,1.042 false 0.896,1.604 0.896,1.333 false 2.5,2.49 2.5,2.219 false 2.917,2.76 2.917,2.49 false 1.917,2.271 1.917,2 false 1.333,2 1.333,1.729 false 2.427,2.521 2.74,2.677 0.313,0.156 10 false *1 0.354,1.354 0.667,1.51 0.313,0.156 10 false *2 0.833,1.635 1.146,1.792 0.313,0.156 10 false *1 2.844,2.802 3.156,2.958 0.313,0.156 10 false *2 1.854,2.302 2.167,2.458 0.313,0.156 10 false *3 1.271,2.01 1.583,2.167 0.313,0.156 10 false *3
*1 Rear No. 1 Disc Brake Anti Squeal Shim
*2 Rear No. 2 Disc Brake Anti Squeal Shim
*3 Rear Disc Brake Pad


Install the rear No. 1 disc brake anti squeal shim and rear No. 2 disc brake anti squeal shim to each rear disc brake pad.

NOTICE:
·

Install the anti squeal shims in the correct positions and directions.

·

When replacing worn pads, the anti squeal shims must be replaced together with the rear disc brake pads.

·

Make sure that disc brake grease is not applied onto the lining surface.




Hide 04466 7.INSTALL REAR DISC BRAKE PAD

a.

Install the 2 rear disc brake pads to the rear disc brake cylinder mounting.

NOTICE:

There should be no oil or grease on the friction surfaces of the rear disc brake pads or the rear disc.



Hide 47850 8.INSTALL REAR DISC BRAKE CYLINDER ASSEMBLY

a.
C219089E03
1.365,1.875 1.906,1.875 true 1.927,1.792 2.229,1.938 0.302,0.146 10 false SST 1.052,3.365 1.292,3.552 0.24,0.188 10 true 90°

To compensate for pad lining thickness, use SST to adjust the protrusion of the rear disc brake piston by turning it.

SST
09719-12010  (09719-01030)

NOTICE:
·

Place the disc between the 2 brake pads and determine the piston return value.

·

Turn the rear disc brake piston to the position where the protrusion on the rear disc brake pad lines up properly with the piston groove.




b.

Hold each rear disc brake pad guide pin, and install the rear disc brake cylinder assembly to the rear disc brake cylinder mounting with the 2 bolts.

Torque:
34.3 N*m (350 kgf*cm, 25 ft.*lbf)


Hide 47319F 9.CONNECT REAR FLEXIBLE HOSE

a.
C294091C01
1.385,1.385 0.917,1.844 true 0.719,1.802 0.875,1.979 0.156,0.177 10 true *a
*a Lock Hole


Connect the rear flexible hose to the rear disc brake cylinder assembly with a new union bolt and a new gasket.

Torque:
30.4 N*m (310 kgf*cm, 22 ft.*lbf)

NOTICE:

Install the rear flexible hose lock securely into the lock hole in the rear disc brake cylinder assembly.



Hide 46430 10.CONNECT NO. 3 PARKING BRAKE CABLE ASSEMBLY

a.

Engage the clip to install the No. 3 parking brake cable assembly to the rear disc brake cylinder assembly.

NOTICE:

Be sure to engage the clip to the rear disc brake cylinder assembly.



b.

Connect the No. 3 parking brake cable assembly to the rear disc brake cylinder assembly.


Hide 12.INSTALL REAR WHEEL

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)

Hide 13.ADJUST PARKING BRAKE LEVER TRAVEL

Hide 58910C 14.INSTALL REAR CONSOLE BOX ASSEMBLY (w/ Console Box Lid)

Hide 58910C 15.INSTALL REAR CONSOLE BOX ASSEMBLY (w/o Console Box Lid)