Home › Brake › BRAKE (REAR) › REAR BRAKE(for Drum Type) › 2014.03–2017.10
RM30M0E _54 Brake _017101 BRAKE (REAR) _0092769 REAR BRAKE(for Drum Type) A

BRAKE (REAR)  REAR BRAKE(for Drum Type)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the LH side and RH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 47570 1.INSTALL REAR WHEEL BRAKE CYLINDER ASSEMBLY

a.

Install the rear wheel brake cylinder assembly to the backing plate with the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


b.

Using a 10 mm union nut wrench, connect the brake tube to the rear wheel brake cylinder assembly.

Torque:
15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



Hide 2.INSTALL REAR BRAKE PARKING BRAKE SHOE LEVER SUB-ASSEMBLY

a.

Using needle-nose pliers, install the rear brake parking brake shoe lever sub-assembly to the rear brake shoe (rear) with a new C-washer.


Hide 3.INSTALL REAR BRAKE AUTOMATIC ADJUST LEVER

a.

Install the rear brake automatic adjust lever and rear brake automatic adjust lever tension spring to the rear brake shoe (front).


Hide 4.INSTALL REAR BRAKE STRUT KIT

a.

Using needle-nose pliers, install the No. 3 parking brake cable assembly to the rear brake parking brake shoe lever sub-assembly.


b.
C282436C02
0,0 3.427,0 false
V100144

High Temperature Grease


Apply high temperature grease to the surface of the backing plate that contacts the rear brake shoes as shown in the illustration.


c.
C235450C03
0,0 3.427,0 false
V100144

High Temperature Grease


Apply high temperature grease to the adjustment bolt.


d.
C252599

Assemble the rear brake strut kit as shown in the illustration.


e.

Install the rear brake strut kit to the rear brake shoe (rear).


f.
C282433C02
2.677,1.927 2.167,1.365 true 2.75,1.885 3.208,2.083 0.458,0.198 10 false SST

Using SST, install the rear brake shoe (rear), shoe hold down spring pin, shoe hold down spring and shoe hold down spring cup.

SST
09718-00011  


g.
C282432

Install the shoe tension spring to the rear brake shoe (front) and rear brake shoe (rear).


h.
C282431C01
0.875,1.833 1.479,1.313 true 0.656,1.896 1.115,2.094 0.458,0.198 10 false SST

Using SST, install the rear brake shoe (front), shoe hold down spring pin, shoe hold down spring and shoe hold down spring cup.

SST
09718-00011  


i.
C282430C03
2.083,0.542 2.719,0.146 true 0.969,1.958 1.365,1.677 true 2.26,0.792 2.885,0.406 true 2.813,0.063 3.125,0.219 0.313,0.156 10 false *1 2.969,0.344 3.281,0.5 0.313,0.156 10 false *2 0.646,1.927 0.958,2.083 0.313,0.156 10 false SST
*1 Wheel Cylinder Boot
*2 Tension Spring


Using SST, install the tension spring to the rear brake shoe (front).

SST
09921-00011  

NOTICE:

Do not damage the wheel cylinder boot.



j.
C296512C01
1.854,0.771 2.177,0.427 false 1.729,1.771 2.01,1.396 false 2.26,0.354 2.573,0.552 0.313,0.198 10 false *1 1.51,1.74 1.823,1.938 0.313,0.198 10 false *2
*1 Backing Plate
*2 Rear Brake Strut Kit


Inspect the rear brake strut kit is installed properly as shown in the illustration.


Hide 5.INSPECT REAR DRUM BRAKE

a.

Inspect that each part is installed properly as shown in the illustration.

C241885C01
0.333,0.26 0.646,0.417 0.313,0.156 10 false *a 3.938,0.26 4.25,0.417 0.313,0.156 10 false *b
*a LH Side *b RH Side
V100135

Front of the Vehicle - -


NOTICE:

There should be no oil or grease adhering to the friction surfaces of the shoe lining or the drum.



Hide 42403 6.INSTALL REAR BRAKE DRUM SUB-ASSEMBLY

a.

Install the rear brake drum sub-assembly.


Hide 7.ADJUST REAR DRUM BRAKE SHOE CLEARANCE

a.
C233136C01
0,0 3.427,0 false
V100135

Expand


Temporarily install the 2 wheel nuts.


b.

Turn the adjuster to expand the shoe until the drum locks.


c.
C233134C08
0,0 3.427,0 false
V100135

Contract


Hold the rear brake automatic adjust lever away from the adjuster, and contract the rear brake shoe by turning the adjust bolt using another screwdriver until the drum can rotate smoothly.

Standard:

12 notches



d.

Install the shoe adjusting hole plug.


e.

Remove the 2 wheel nuts.


Hide 9.INSTALL REAR WHEEL

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)

Hide 10.ADJUST PARKING BRAKE LEVER TRAVEL

Hide 58910C 11.INSTALL REAR CONSOLE BOX ASSEMBLY (w/ Console Box Lid)

Hide 58910C 12.INSTALL REAR CONSOLE BOX ASSEMBLY (w/o Console Box Lid)