Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM › 2014.03–2017.10
RM30M0E _58 Vehicle Interior _017111 THEFT DETERRENT / KEYLESS ENTRY _0090853 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  While Alarm is Armed, Engine Hood is opened but Alarm does not Sound  


DESCRIPTION

A situation in which the alarm is armed but does not sound when the engine hood is opened can be caused when the body computer cannot detect whether the engine hood courtesy switch is open or closed.

If the alarm does not sound, there may be a malfunction in the engine hood courtesy switch, body computer or a wire harness.

WIRING DIAGRAM

E293073E02
1.563,1.229 1.719,1.427 0.156,0.198 10 false 2 2.844,1.229 3,1.427 0.156,0.198 10 false 1 1.385,1.646 1.74,1.833 0.354,0.188 10 false A29 1.375,1.792 3.208,2.177 1.833,0.385 10 false Engine Hood Courtesy Switch (Hood Lock Assembly) 4.323,1.146 4.479,1.344 0.156,0.198 10 false 9 5.51,1.146 5.865,1.333 0.354,0.188 10 false 20 4.271,1.323 4.625,1.51 0.354,0.188 10 false 2D 5.479,1.323 5.833,1.51 0.354,0.188 10 false MB 5.792,1.323 6.344,1.521 0.552,0.198 10 false HCTY 5.854,2.521 7.031,2.792 1.177,0.271 10 false Body Computer 4.396,2.198 5.719,2.625 1.323,0.427 10 false Driver Side Junction Block Assembly

PROCEDURE

1.CHECK SECURITY INDICATOR LIGHT OPERATION
a.

Close all doors and the engine hood.


b.

Lock the doors using the wireless operation or entry operation.


c.

Check that the security indicator light illuminates.


d.

After 30 seconds have elapsed, check that the security indicator light changes from illuminated to flashing.


HINT:

The illumination status of the security indicator light can be used to determine whether the theft deterrent system is set or unset.


Result:
Proceed to
OK
NG



OK

2.INSPECT HOOD LOCK ASSEMBLY

NG

2.INSPECT HOOD LOCK ASSEMBLY


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (HOOD LOCK ASSEMBLY - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)

NG

3.CHECK HARNESS AND CONNECTOR (HOOD LOCK ASSEMBLY - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the A29 hood lock assembly connector.


b.

Disconnect the 2D driver side junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A29-1 - 2D-9 Always Below 1 Ω
A29-2 - Body ground Always Below 1 Ω
A29-1 or 2D-9 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY

b.

Disconnect the driver side junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

B343149C11
2.177,0.417 2.5,0.625 0.323,0.208 5.552,0.229 5.875,0.438 0.323,0.208 1.625,1.208 1.573,0.948 true 0.271,0.156 0.583,0.354 0.313,0.198 10 false *a 5.594,0.271 5.906,0.469 0.313,0.198 10 false 2D 2.219,0.438 2.531,0.635 0.313,0.198 10 false MB 1.448,1.26 2.063,1.458 0.615,0.198 10 false HCTY
*a Component without harness connected
(Driver Side Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
2D-9 - MB-20 (HCTY) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY