Home › Suspension › ALIGNMENT / HANDLING DIAGNOSIS › FRONT WHEEL ALIGNMENT › 2014.03–2017.10
RM30M0E _53 Suspension _017094 ALIGNMENT / HANDLING DIAGNOSIS _0090093 FRONT WHEEL ALIGNMENT N

ALIGNMENT / HANDLING DIAGNOSIS  FRONT WHEEL ALIGNMENT  ADJUSTMENT  


PROCEDURE

Hide 2.MEASURE VEHICLE HEIGHT (for Sedan)

NOTICE:
·

Before inspecting the wheel alignment, adjust the vehicle height to the specified value.

·

Be sure to perform measurement on a level surface.

·

If it is necessary to go under the vehicle for measurement, confirm that the parking brake is applied and the vehicle is secured with chocks.

·

Inspect while the vehicle is unloaded.

·

The standard value shown here is a value that is used for performing a wheel alignment and does not indicate the height of an actual vehicle.



a.

Bounce the vehicle up and down at the corners to stabilize the suspension.


b.
C282308E01
0.469,3.427 0.625,3.625 0.156,0.198 10 false A 2.875,3.385 3.052,3.604 0.177,0.219 10 false B 3.219,3.344 3.375,3.542 0.156,0.198 10 false D 0.156,3.313 0.313,3.51 0.156,0.198 10 false C

Measure the vehicle height.

Vehicle Height (Unloaded Vehicle):
except for Rough Road Package
Front C - A Rear D - B
87 mm (3.43 in.) 16 mm (0.630 in.)

for Rough Road Package
Front C - A Rear D - B
67 mm (2.64 in.) -4 mm (-0.157 in.)


Measurement Points:

A: Ground clearance of front lower No. 1 suspension arm bushing set bolt center


B: Ground clearance of rear trailing arm bushing set bolt center


C: Ground clearance of front wheel center


D: Ground clearance of rear wheel center



Hide 3.MEASURE VEHICLE HEIGHT (for Hatchback)

NOTICE:
·

Before inspecting the wheel alignment, adjust the vehicle height to the specified value.

·

Be sure to perform measurement on a level surface.

·

If it is necessary to go under the vehicle for measurement, confirm that the parking brake is applied and the vehicle is secured with chocks.

·

Inspect while the vehicle is unloaded.

·

The standard value shown here is a value that is used for performing a wheel alignment and does not indicate the height of an actual vehicle.



a.

Bounce the vehicle up and down at the corners to stabilize the suspension.


b.
C288201E01
0.51,3.49 0.667,3.688 0.156,0.198 10 false A 0.156,3.313 0.313,3.51 0.156,0.198 10 false C 2.885,3.396 3.042,3.594 0.156,0.198 10 false B 3.219,3.323 3.375,3.521 0.156,0.198 10 false D

Measure the vehicle height.

Vehicle Height (Unloaded Vehicle):
except for Rough Road Package
Front C - A Rear D - B
87 mm (3.43 in.) 16 mm (0.63 in.)

for Rough Road Package
Front C - A Rear D - B
67 mm (2.64 in.) -4 mm (-0.157 in.)


Measurement Points:

A: Ground clearance of front lower No. 1 suspension arm bushing set bolt center


B: Ground clearance of rear trailing arm bushing set bolt center


C: Ground clearance of front wheel center


D: Ground clearance of rear wheel center



Hide 4.INSPECT CAMBER, CASTER AND STEERING AXIS INCLINATION

NOTICE:

Inspect while the vehicle is unloaded.


a.
C132440C15
0.99,1.479 0.667,1.073 false 2.708,0.75 2.302,1.083 false 2.76,0.667 2.99,0.844 0.229,0.177 10 false *b 0.49,0.969 0.729,1.146 0.24,0.177 10 false *a
*a Turning Radius Gauge
*b Camber-caster-kingpin Gauge


Put the front wheel on the center of the turning radius gauge.


b.

Remove the wheel cap or wheel hub ornament.


c.

Install the camber-caster-kingpin gauge at the center of the drive shaft.


d.

Inspect the camber, caster and steering axis inclination.

Camber (Unloaded Vehicle):
except for Rough Road Package
Tire Size Camber Inclination Right-left Difference
175/65R14 -0°08' +/- 0°45' (-0.13° +/- 0.75°) 0°45' (0.75°) or less
185/60R15 -0°09' +/- 0°45' (-0.15° +/- 0.75°)

for Rough Road Package
Tire Size Camber Inclination Right-left Difference
175/65R14 0°09' +/- 0°45' (0.15° +/- 0.75°) 0°45' (0.75°) or less
185/60R15 0°08' +/- 0°45' (0.13° +/- 0.75°)


Caster (Unloaded Vehicle):
except for Rough Road Package
Tire Size Caster Inclination Right-left Difference
175/65R14 4°41' +/- 0°45' (4.68° +/- 0.75°) 0°45' (0.75°) or less
185/60R15 4°42' +/- 0°45' (4.70° +/- 0.75°)

for Rough Road Package
Tire Size Caster Inclination Right-left Difference
175/65R14 4°24' +/- 0°45' (4.40° +/- 0.75°) 0°45' (0.75°) or less
185/60R15 4°25' +/- 0°45' (4.42° +/- 0.75°)


Steering Axis Inclination (Unloaded Vehicle):
except for Rough Road Package
Steering Axis Inclination (Reference)
11°03' (11.05°)

for Rough Road Package
Steering Axis Inclination (Reference)
10°32' (10.53°)


If the camber, caster and steering axis inclination are not within the specified range, inspect the suspension parts for damage and wear, and replace them if necessary.


e.

Remove the camber-caster-kingpin gauge.


f.

Install the wheel cap or wheel hub ornament.


Hide 5.ADJUST CAMBER

NOTICE:

Inspect toe-in after the camber has been adjusted.


a.

Remove the front wheel.


b.

w/ ABS:

i.
C283559

Remove the bolt and separate the front flexible hose and front speed sensor wire from the front shock absorber assembly.



c.
C286969

Remove the 2 nuts from the lower side of the front shock absorber assembly.

HINT:

Keep the bolt from rotating while turning the nut.



d.

Clean the installation surfaces of the front shock absorber assembly and steering knuckle.


e.

Temporarily install the 2 nuts. (Step A)


f.
C110325E01
0.651,0.189 0.904,0.352 0.253,0.163 10 (-) 2.197,0.189 2.513,0.373 0.316,0.184 10 (+)

Fully push or pull the front axle hub in the direction of the required adjustment. (Step B)


g.
C286969

Tighten the 2 nuts.

Torque:
164 N*m (1672 kgf*cm, 121 ft.*lbf)

NOTICE:

Keep the bolts from rotating when tightening the nuts.



h.

w/ ABS:

i.

Install the front flexible hose and front speed sensor wire to the front shock absorber assembly with the bolt.

Torque:
30.4 N*m (310 kgf*cm, 22 ft.*lbf)

NOTICE:

Install the front flexible hose and front speed sensor wire without twisting them.


HINT:

Install the front speed sensor harness bracket first and then the front flexible hose bracket.




i.

Install the front wheel.

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)


j.
C286970E01
0.281,0.885 0.5,0.99 false 0.292,1.115 0.51,1.219 false 0.156,0.76 0.313,0.958 0.156,0.198 10 false 1 0.188,1.031 0.344,1.229 0.156,0.198 10 false 2

Check the camber.

If the measured value is not within the specification, calculate the required adjustment amount using the formula below.

Camber adjustment amount = center of the specified range - measured value

Check the combination of the installed bolts. Select appropriate bolts from the tables below to adjust the camber to the specified values.

HINT:

Try to adjust the camber to the center of the specified range.


To move the axle hub toward (+) in step B To move the axle hub toward (-) in step B
Refer to table (1) (To move the axle hub toward the positive side) Refer to table (2) (To move the axle hub toward the negative side)

i.

Table (1) (To move the axle hub toward the positive side)

C212217C11
2.052,0.531 2.188,0.74 0.135,0.208 10 false 1 2.052,1.146 2.188,1.354 0.135,0.208 10 false 2 2.521,0.792 2.75,0.99 0.229,0.198 10 false *d 3.219,1.406 3.448,1.594 0.229,0.188 10 false *e 5.979,0.792 6.198,0.99 0.219,0.198 10 false *f 5.271,0.792 5.521,0.99 0.25,0.198 10 false *e 4.604,1.385 4.781,1.563 0.177,0.177 10 false *g 3.917,1.406 4.125,1.615 0.208,0.208 10 false *f 4.396,6.354 4.583,6.531 0.188,0.177 10 false *g 5.969,1.385 6.167,1.604 0.198,0.219 10 false *g 5.271,1.385 5.469,1.563 0.198,0.177 10 false *g 6.646,1.385 6.823,1.604 0.177,0.219 10 false *g 6.646,0.771 6.854,0.948 0.208,0.177 10 false *g 2.542,3.052 2.719,3.281 0.177,0.229 10 false A 2.542,4.25 2.771,4.469 0.229,0.219 10 false F 2.542,3.531 2.771,3.75 0.229,0.219 10 false C 2.542,4 2.74,4.219 0.198,0.219 10 false E 2.542,3.271 2.729,3.479 0.188,0.208 10 false B 2.542,3.76 2.729,3.979 0.188,0.219 10 false D 3.927,3.052 4.177,3.281 0.25,0.229 10 false C 5.271,3.042 5.51,3.271 0.24,0.229 10 false E 3.229,3.052 3.406,3.26 0.177,0.208 10 false B 4.604,3.042 4.792,3.281 0.188,0.24 10 false D 3.229,2.802 3.448,3.031 0.219,0.229 10 false G 3.229,3.281 3.406,3.49 0.177,0.208 10 false C 3.219,3.76 3.438,3.99 0.219,0.229 10 false E 3.229,3.51 3.427,3.74 0.198,0.229 10 false D 3.229,4.01 3.427,4.24 0.198,0.229 10 false F 3.927,2.552 4.115,2.781 0.188,0.229 10 false G 3.927,2.802 4.135,3.01 0.208,0.208 10 false A 3.927,3.76 4.115,3.99 0.188,0.229 10 false F 3.917,3.521 4.083,3.74 0.167,0.219 10 false E 3.927,3.281 4.135,3.5 0.208,0.219 10 false D 4.604,2.323 4.802,2.573 0.198,0.25 10 false G 6.656,1.563 6.833,1.823 0.177,0.26 10 false G 5.979,1.854 6.26,2.104 0.281,0.25 10 false G 5.271,2.073 5.458,2.323 0.188,0.25 10 false G 6.656,1.854 6.813,2.083 0.156,0.229 10 false A 6.656,2.333 6.844,2.583 0.188,0.25 10 false C 6.656,2.802 6.885,3.052 0.229,0.25 10 false E 6.656,2.073 6.833,2.302 0.177,0.229 10 false B 6.656,2.552 6.875,2.823 0.219,0.271 10 false D 5.979,2.083 6.177,2.344 0.198,0.26 10 false A 5.979,2.563 6.188,2.802 0.208,0.24 10 false C 5.979,2.333 6.26,2.583 0.281,0.25 10 false B 5.979,2.802 6.167,3.031 0.188,0.229 10 false D 5.979,3.042 6.115,3.25 0.135,0.208 10 false F 5.271,3.292 5.49,3.5 0.219,0.208 10 false F 5.271,2.323 5.406,2.552 0.135,0.229 10 false A 5.271,2.802 5.448,3.01 0.177,0.208 10 false C 5.271,2.552 5.438,2.781 0.167,0.229 10 false B 4.604,2.552 4.781,2.802 0.177,0.25 10 false A 4.604,2.802 4.781,3.01 0.177,0.208 10 false B 4.604,3.281 4.813,3.5 0.208,0.219 10 false E 4.604,3.552 4.813,3.781 0.208,0.229 10 false F 1.625,5.073 1.76,5.281 0.135,0.208 10 false A 5.094,5.073 5.229,5.281 0.135,0.208 10 false F 3.052,5.073 3.188,5.281 0.135,0.208 10 false C 4.406,5.073 4.542,5.281 0.135,0.208 10 false E 2.344,5.073 2.479,5.281 0.135,0.208 10 false B 3.729,5.073 3.865,5.281 0.135,0.208 10 false D 5.802,5.073 5.938,5.281 0.135,0.208 10 false G 1.094,5.5 1.229,5.708 0.135,0.208 10 false 1 1.104,6.135 1.24,6.344 0.135,0.208 10 false 2 3.021,6.344 3.208,6.573 0.188,0.229 10 false *g 3.698,6.333 3.938,6.542 0.24,0.208 10 false *g 5.073,6.344 5.281,6.542 0.208,0.198 10 false *g 5.083,5.729 5.271,5.938 0.188,0.208 10 false *g 4.385,5.75 4.604,5.917 0.219,0.167 10 false *f 2.333,6.375 2.542,6.542 0.208,0.167 10 false *f 1.625,6.375 1.854,6.552 0.229,0.177 10 false *e 3.719,5.75 3.927,5.938 0.208,0.188 10 false *e 3.01,5.75 3.208,5.938 0.198,0.188 10 false *d 1.625,5.75 1.844,5.948 0.219,0.198 10 false *d 2.333,5.75 2.521,5.906 0.188,0.156 10 false *d 5.802,6.365 6.021,6.563 0.219,0.198 10 false *d 5.76,5.76 5.969,5.948 0.208,0.188 10 false *d 0.177,1.563 2.198,1.75 2.021,0.188 10 false -1°30' to -1°15' (-1.50° to -1.25°) 0.406,2.76 1.969,2.948 1.563,0.188 10 false -0°15' to 0° (-0.25° to 0°) 0.208,2.51 2.156,2.729 1.948,0.219 10 false -0°30' to -0°15' (-0.5° to -0.25°) 0.208,2.281 2.156,2.479 1.948,0.198 10 false -0°45' to -0°30' (-0.75° to -0.5°) 0.271,2.031 2.104,2.208 1.833,0.177 10 false -1°00' to -0°45' (-1° to -0.75°) 0.26,1.813 2.094,2.021 1.833,0.208 10 false -1°15' to -1°00' (-1.25° to -1°) 0.354,3.938 2.01,4.115 1.656,0.177 10 false 1°00' to 1°15' (1° to 1.25°) 0.354,3.708 2,3.906 1.646,0.198 10 false 0°45' to 1°00' (0.75° to 1°) 0.302,3.469 2.073,3.646 1.771,0.177 10 false 0°30' to 0°45' (0.5° to 0.75°) 0.302,3.24 2.073,3.417 1.771,0.177 10 false 0°15' to 0°30' (0.25° to 0.5°) 0.448,3 1.917,3.198 1.469,0.198 10 false 0° to 0°15' (0° to 0.25°) 0.302,4.188 2.073,4.365 1.771,0.177 10 false 1°15' to 1°30' (1.25° to 1.5°) 2.542,1.406 2.76,1.604 0.219,0.198 10 false *d 3.219,0.792 3.448,0.969 0.229,0.177 10 false *d 3.917,0.792 4.135,1.01 0.219,0.219 10 false *d 4.604,0.792 4.823,1.01 0.219,0.219 10 false *d 1.25,0.719 1.427,0.885 0.177,0.167 10 false *b 0.75,1.146 0.927,1.313 0.177,0.167 10 false *c 0.875,4.75 1.198,4.979 0.323,0.229 10 false *h 0.083,0.115 0.354,0.313 0.271,0.198 10 false *a
*a Table (1) (To move the axle hub toward the positive side) *b Installed Bolt
*c Adjusting Value *d 90109-15001
*e 90109-15002 *f 90109-15003
*g 90109-15004 *h Selected Bolt Combination



ii.

Table (2) (To move the axle hub toward the negative side)

C212218C11
2.052,0.531 2.188,0.74 0.135,0.208 10 false 1 2.052,1.146 2.188,1.354 0.135,0.208 10 false 2 1.635,5.052 1.771,5.26 0.135,0.208 10 false A 5.094,5.052 5.229,5.26 0.135,0.208 10 false F 3.052,5.052 3.188,5.26 0.135,0.208 10 false C 4.406,5.052 4.542,5.26 0.135,0.208 10 false E 2.344,5.052 2.479,5.26 0.135,0.208 10 false B 3.729,5.052 3.865,5.26 0.135,0.208 10 false D 5.802,5.052 5.938,5.26 0.135,0.208 10 false G 1.094,5.5 1.229,5.708 0.135,0.208 10 false 1 1.104,6.135 1.24,6.344 0.135,0.208 10 false 2 0.188,1.563 2.208,1.75 2.021,0.188 10 false -1°30' to -1°15' (-1.50° to -1.25°) 0.406,2.76 1.969,2.948 1.563,0.188 10 false -0°15' to 0° (-0.25° to 0°) 0.208,2.521 2.156,2.74 1.948,0.219 10 false -0°30' to -0°15' (-0.5° to -0.25°) 0.208,2.281 2.156,2.479 1.948,0.198 10 false -0°45' to -0°30' (-0.75° to -0.5°) 0.271,2.031 2.104,2.208 1.833,0.177 10 false -1°00' to -0°45' (-1° to -0.75°) 0.26,1.813 2.094,2.021 1.833,0.208 10 false -1°15' to -1°00' (-1.25° to -1°) 0.354,3.938 2.01,4.115 1.656,0.177 10 false 1°00' to 1°15' (1° to 1.25°) 0.354,3.708 2,3.906 1.646,0.198 10 false 0°45' to 1°00' (0.75° to 1°) 0.302,3.469 2.073,3.646 1.771,0.177 10 false 0°30' to 0°45' (0.5° to 0.75°) 0.302,3.24 2.073,3.417 1.771,0.177 10 false 0°15' to 0°30' (0.25° to 0.5°) 0.448,3 1.917,3.198 1.469,0.198 10 false 0° to 0°15' (0° to 0.25°) 0.302,4.188 2.073,4.365 1.771,0.177 10 false 1°15' to 1°30' (1.25° to 1.5°) 1.156,0.625 1.333,0.792 0.177,0.167 10 false *b 0.625,1.115 0.802,1.281 0.177,0.167 10 false *c 0.875,4.792 1.167,5.021 0.292,0.229 10 false *h 0.063,0.135 0.417,0.354 0.354,0.219 10 false *a 5.271,2.802 5.406,3.01 0.135,0.208 10 false E 5.292,3.74 5.427,3.948 0.135,0.208 10 false G 5.292,2.552 5.427,2.76 0.135,0.208 10 false F 5.292,3.5 5.427,3.708 0.135,0.208 10 false A 5.292,3.031 5.427,3.24 0.135,0.208 10 false C 5.292,3.271 5.427,3.479 0.135,0.208 10 false B 2.542,2.802 2.677,3.01 0.135,0.208 10 false A 2.542,1.604 2.677,1.813 0.135,0.208 10 false F 2.542,2.323 2.677,2.531 0.135,0.208 10 false C 2.542,1.865 2.677,2.073 0.135,0.208 10 false E 2.542,2.563 2.677,2.771 0.135,0.208 10 false B 2.542,2.073 2.677,2.281 0.135,0.208 10 false D 3.229,2.802 3.365,3.01 0.135,0.208 10 false B 3.208,3.063 3.344,3.271 0.135,0.208 10 false G 3.229,2.563 3.365,2.771 0.135,0.208 10 false C 3.229,2.073 3.365,2.281 0.135,0.208 10 false E 3.229,2.323 3.365,2.531 0.135,0.208 10 false D 3.229,1.854 3.375,2.063 0.146,0.208 10 false F 3.927,2.792 4.063,3 0.135,0.208 10 false C 3.927,3.281 4.063,3.49 0.135,0.208 10 false G 3.927,3.031 4.063,3.24 0.135,0.208 10 false A 3.927,2.073 4.063,2.281 0.135,0.208 10 false F 3.927,2.323 4.063,2.531 0.135,0.208 10 false E 3.927,2.552 4.063,2.76 0.135,0.208 10 false D 4.604,2.792 4.74,3 0.135,0.208 10 false D 4.604,3.5 4.74,3.708 0.135,0.208 10 false G 4.604,3.271 4.74,3.479 0.135,0.208 10 false A 4.604,3.031 4.74,3.24 0.135,0.208 10 false B 4.604,2.552 4.74,2.76 0.135,0.208 10 false E 4.604,2.313 4.74,2.521 0.135,0.208 10 false F 5.99,3.969 6.125,4.177 0.135,0.208 10 false G 5.99,3.74 6.125,3.948 0.135,0.208 10 false A 5.99,3.271 6.125,3.479 0.135,0.208 10 false C 5.99,3.5 6.125,3.708 0.135,0.208 10 false B 5.99,3.042 6.125,3.25 0.135,0.208 10 false D 5.99,2.792 6.125,3 0.135,0.208 10 false F 6.688,4.219 6.823,4.427 0.135,0.208 10 false G 6.688,3.969 6.823,4.177 0.135,0.208 10 false A 6.688,3.5 6.823,3.708 0.135,0.208 10 false C 6.688,3.031 6.823,3.24 0.135,0.208 10 false E 6.688,3.74 6.823,3.948 0.135,0.208 10 false B 6.688,3.271 6.823,3.479 0.135,0.208 10 false D 2.51,0.792 2.729,0.969 0.219,0.177 10 false *d 3.219,1.396 3.406,1.573 0.188,0.177 10 false *e 5.969,0.781 6.115,0.938 0.146,0.156 10 false *f 5.271,0.792 5.469,0.979 0.198,0.188 10 false *e 4.594,1.365 4.771,1.573 0.177,0.208 10 false *g 3.906,1.396 4.083,1.573 0.177,0.177 10 false *f 5.969,1.375 6.167,1.573 0.198,0.198 10 false *g 5.271,1.365 5.458,1.573 0.188,0.208 10 false *g 6.656,1.375 6.833,1.563 0.177,0.188 10 false *g 6.656,0.771 6.823,0.938 0.167,0.167 10 false *g 2.51,1.396 2.688,1.573 0.177,0.177 10 false *d 3.219,0.792 3.396,0.948 0.177,0.156 10 false *d 3.927,0.792 4.115,0.979 0.188,0.188 10 false *d 4.604,0.792 4.781,0.958 0.177,0.167 10 false *d 4.396,6.344 4.552,6.563 0.156,0.219 10 false *g 3,6.354 3.188,6.583 0.188,0.229 10 false *g 3.698,6.344 3.927,6.563 0.229,0.219 10 false *g 5.083,6.354 5.292,6.583 0.208,0.229 10 false *g 5.073,5.729 5.271,5.938 0.198,0.208 10 false *g 4.375,5.75 4.573,5.906 0.198,0.156 10 false *f 2.313,6.375 2.521,6.542 0.208,0.167 10 false *f 1.625,6.375 1.771,6.531 0.146,0.156 10 false *e 3.688,5.75 3.875,5.938 0.188,0.188 10 false *e 3.01,5.75 3.208,5.938 0.198,0.188 10 false *d 1.625,5.74 1.802,5.927 0.177,0.188 10 false *d 2.323,5.75 2.5,5.906 0.177,0.156 10 false *d 5.781,6.375 5.969,6.542 0.188,0.167 10 false *d 5.771,5.75 5.979,5.938 0.208,0.188 10 false *d
*a Table (2) (To move the axle hub toward the negative side) *b Installed Bolt
*c Adjusting Value *d 90109-15001
*e 90109-15002 *f 90109-15003
*g 90109-15004 *h Selected Bolt Combination


The body and suspension may be damaged if the camber is not correctly adjusted in accordance with the above table.

NOTICE:

Replace the nut with a new one when replacing the bolt.




k.

Repeat the steps mentioned above. At step (A), replace 1 or 2 selected bolts.

HINT:

Replace one bolt at a time when replacing both bolts.



Hide 6.INSPECT TOE-IN

NOTICE:

Inspect while the vehicle is unloaded.


a.

Bounce the vehicle up and down at the corners to stabilize the suspension.


b.

Release the parking brake and move the shift lever to neutral.


c.

Push the vehicle straight ahead approximately 5 m (16.4 ft.). (Step A)


d.
C188968C19
2.521,1.333 2.521,1.667 false 0.823,0.552 0.844,1.094 0.844,1.094 1.333,0.594 true 0.76,1.135 0.938,1.302 0.177,0.167 10 false *a 2.427,1.698 2.604,1.854 0.177,0.156 10 false *b
*a Tread Center Mark
*b Dimension B
V100135

Front of the Vehicle


Put tread center marks on the rearmost points of the front wheels and measure the distance between the marks (dimension B).


e.

Slowly push the vehicle straight ahead to cause the front wheels to rotate 180°. Use the front tire valve as a reference point.

NOTICE:

Do not allow the wheels to rotate more than 180°. If the wheels rotate more than 180°, perform the procedure from (Step A) again.



f.
C188969C02
0.646,1.271 0.646,1.635 false 1.917,0.542 2.052,0.698 0.135,0.156 10 C 3.073,0.552 3.208,0.708 0.135,0.156 10 D 2.5,0.719 2.635,0.875 0.135,0.156 10 A 2.51,1.542 2.646,1.698 0.135,0.156 10 B 0.563,1.656 0.74,1.813 0.177,0.156 10 *a
*a Dimension A
V100135

Front of the Vehicle


Measure the distance between the tread center marks on the front of the wheels (dimension A).

Toe-in (Unloaded Vehicle):
except for Rough Road Package
Specified Condition
C + D: 0°09' +/- 0°12' (0.15° +/- 0.20°)
B - A: 1.4 +/- 2.0 mm (0.0551 +/- 0.0787 in.)

for Rough Road Package
Specified Condition
C + D: 0°07' +/- 0°12' (0.12° +/- 0.20°)
B - A: 1.1 +/- 2.0 mm (0.0433 +/- 0.0787 in.)


HINT:

Measure "B - A" only when "C + D" cannot be measured.


If the toe-in is not within the specified range, adjust it at the rack ends.


Hide 7.ADJUST TOE-IN

a.
C288599C01
2.365,0.219 2.552,0.406 0.188,0.188 10 true *a
*a Thread Length


Make sure that the thread length of the right and left rack ends are approximately the same.

Standard difference:

1.5 mm (0.0591 in.) or less



b.

Remove the steering rack boot clips.


c.
C131801

Loosen the tie rod end lock nuts.


d.

Adjust the rack ends if the difference in thread length between the right and left rack ends is not within the specified range.

i.

Extend the shorter rack end if the measured toe-in deviates toward the outer-side.


ii.

Shorten the longer rack end if the measured toe-in deviates toward the inner-side.


iii.

Measure the toe-in.



e.

Turn the right and left rack ends by an equal amount to adjust the toe-in.

HINT:

Try to adjust the toe-in to the center of the specified range.



f.

Make sure that the thread length of the right and left rack ends are the same.


g.

Tighten the tie rod end lock nuts.

Torque:
74.5 N*m (760 kgf*cm, 55 ft.*lbf)


h.

Place the boots on the seats and install the steering rack boot clips.

HINT:

Make sure that the boots are not twisted.



Hide 8.INSPECT WHEEL ANGLE

NOTICE:

Inspect while the vehicle is unloaded.


a.
C132439C03
0.863,0.204 1.036,0.381 0.173,0.177 10 *b 0.538,0.204 0.713,0.381 0.176,0.177 10 *a 2.397,0.204 2.57,0.381 0.173,0.177 10 *b 2.725,0.204 2.901,0.381 0.176,0.177 10 *a
*a Inside
*b Outside
V100135

Front of the Vehicle


Put tread center marks on the rearmost points of a turning radius gauge.


b.

Turn the steering wheel fully to the left and right, and measure the turning angle.

Wheel Turning Angle (Unloaded Vehicle):
except for Rough Road Package
Tire Size Inside Wheel Outside Wheel
175/65R14 38°19' +/- 2°00' (38.32° +/- 2°) 33°16' (33.27°)
185/60R15 38°20' +/- 2°00' (38.33° +/- 2°)

for Rough Road Package
Tire Size Inside Wheel Outside Wheel
175/65R14 38°46' +/- 2°00' (38.77° +/- 2°) 33°36' (33.60°)
185/60R15 38°47' +/- 2°00' (38.78° +/- 2°)


If the right and left inside wheel angles differ from the specified range, check and adjust the right and left rack end lengths.