Home › Vehicle Exterior › WINDOW / GLASS › BACK DOOR GLASS › 2014.03–2017.10
RM30M0E _59 Vehicle Exterior _017121 WINDOW / GLASS _0120180 BACK DOOR GLASS A

WINDOW / GLASS  BACK DOOR GLASS  INSTALLATION  


PROCEDURE

Hide 68131 1.CLEAN BACK DOOR GLASS

a.

Using a scraper, remove any back door glass adhesive dam and adhesive residue from the back door glass.

NOTICE:

Be careful not to damage the back door glass.



b.
B187131

Clean the outer circumference of the back door glass with a non-residue solvent.

NOTICE:
·

Do not touch the back door glass surface after cleaning it.

·

Be careful not to damage the back door glass.

·

Even if using new back door glass, clean it with a non-residue solvent.




Hide 2.CLEAN VEHICLE BODY

a.
B149737C22
0.833,1.542 1.083,1.75 true 0.667,0.5 1,0.667 false 2.167,0.49 2.5,0.656 false 2.281,1.521 2.531,1.729 true 1.125,1.74 1.531,2 0.406,0.26 10 false *a 2.583,1.729 2.969,2 0.385,0.271 10 false *a 0.5,0.385 0.813,0.604 0.313,0.219 10 false *b 2.01,0.375 2.281,0.594 0.271,0.219 10 false *b
*a Adhesive
*b Vehicle Body


Clean and shape the contact surface of the vehicle body.

i.

Using a knife, cut away any rough adhesive on the contact surface of the vehicle body to ensure the appropriate surface shape.

NOTICE:

Be careful not to damage the vehicle body.


HINT:

Leave as much adhesive on the vehicle body as possible.



ii.

Clean the contact surface of the vehicle body with a piece of cloth saturated with cleaner.

HINT:

Even if all the adhesive has been removed, clean the vehicle body.




Hide 3.INSTALL BACK WINDOW MOULDING PAD

a.

Using a brush or sponge, coat the application area of the back window moulding pad with primer G.

NOTICE:
·

Do not apply too much primer G.

·

Allow the primer G coating to dry for 3 minutes or more.

·

Do not keep any of the opened primer G for later use.



HINT:

If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.



b.

Install 2 new back window moulding pads onto the back door glass, as shown in the illustration.

B348244
0.719,1.208 0.552,1.135 false 6.781,1.458 6.552,1.458 false 0.635,1.729 0.51,1.792 false 0.615,1.49 0.385,1.49 false 6.667,1.135 6.448,1.208 false 6.708,1.76 6.521,1.729 false 0.198,1.406 0.51,1.563 0.313,0.156 10 false *1 0.073,0.052 0.385,0.208 0.313,0.156 10 false *a 0.365,1.042 0.677,1.198 0.313,0.156 10 false *b 6.844,1.375 7.156,1.531 0.313,0.156 10 false *1 0.333,1.708 0.646,1.865 0.313,0.156 10 false *b 6.708,1.042 7.021,1.198 0.313,0.156 10 false *b 6.74,1.677 7.052,1.833 0.313,0.156 10 false *b
*1 Back Window Moulding Pad - -
*a Back Side *b Ceramic Notch



Hide 68294C 4.INSTALL BACK DOOR GLASS ADHESIVE DAM

a.

Using a brush or sponge, coat the application area of the back door glass adhesive dam with primer G.

NOTICE:
·

Do not apply too much primer G.

·

Allow the primer G coating to dry for 3 minutes or more.

·

Do not keep any of the opened primer G for later use.



HINT:

If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.



b.

Install the 2 back door adhesive dams onto the back door glass, as shown in the illustration.

B348247
0.698,0.927 0.865,0.865 false 4.479,0.865 4.365,0.729 false 4.281,0.948 4.25,0.833 false 0.625,3 0.469,3.115 false 4.615,3.115 4.469,2.958 false 4.521,3.177 4.385,3.135 false 0.708,0.708 0.833,0.552 true 0.406,3.354 0.646,3.323 true 4.208,0.958 4.521,1.115 0.313,0.156 10 false *1 2.865,1.333 3.063,1.51 0.198,0.177 10 false A 0.052,0.042 0.365,0.198 0.313,0.156 10 false *a 0.854,0.448 1.167,0.604 0.313,0.156 10 false *b 2.875,1.74 3.073,1.917 0.198,0.177 10 false A 2.854,2.927 3,3.104 0.146,0.177 10 true B 2.854,3.344 3.052,3.521 0.198,0.177 10 false B 5.427,0.333 5.885,0.531 0.458,0.198 10 false A - A 5.479,2.052 5.938,2.25 0.458,0.198 10 false B - B 4.438,0.875 4.75,1.031 0.313,0.156 10 false *b 4.313,2.875 4.625,3.031 0.313,0.156 10 false *b 0.646,2.917 0.958,3.073 0.313,0.156 10 false *b 6.313,0.906 6.51,1.083 0.198,0.177 10 false a 6.323,3.031 6.521,3.208 0.198,0.177 10 false a 4.229,3.042 4.542,3.198 0.313,0.156 10 false *1 0.563,0.854 0.875,1.01 0.313,0.156 10 false *1 0.26,3.281 0.573,3.438 0.313,0.156 10 false *1
*1 Back Door Glass Adhesive Dam - -
*a Back Side *b Ceramic Notch


Standard Dimension:
Area Dimension Area Dimension
a 7.6 mm (0.299 in.) or more - -



Hide 68131 5.INSTALL BACK DOOR GLASS

a.

Position the back door glass.

i.
B349478
2.115,1.719 1.615,1.438 1.615,1.438 1.99,1.458 true 1.448,1.323 1.781,1.521 0.333,0.198 10 false *a
*a Matchmarks


Using suction cups, place the back door glass in the correct position.


ii.

Check that the whole contact surface of the back door glass rim is perfectly even.


iii.

Align the matchmarks on the back door glass and vehicle body.


iv.

Remove the back door glass.



b.
B317081C03
1.958,0.708 2.281,0.844 false 2,1.99 2.219,1.906 false 1.958,1.646 2.271,1.781 false 3,0.479 3.313,0.677 0.313,0.198 10 false *c 2.958,1.438 3.271,1.635 0.313,0.198 10 false *d 1.802,0.615 2.115,0.813 0.313,0.198 10 false *a 1.823,1.927 2.135,2.125 0.313,0.198 10 false *b 1.802,1.542 2.115,1.74 0.313,0.198 10 false *a
*a Primer M
*b Adhesive
*c Correct
*d Incorrect


Using a brush, coat the installation surface on the vehicle body with primer M.

NOTICE:
·

Do not coat the adhesive with primer M.

·

Do not apply too much primer M.

·

Allow the primer coating to dry for 3 minutes or more.

·

Do not keep any of the opened primer M for later use.




c.

Using a brush or sponge, coat the adhesive application area with primer G.

B348248
0.042,0.042 0.354,0.198 0.313,0.156 10 false *a 0.604,3.542 0.917,3.698 0.313,0.156 10 false : *b 0.146,1.167 0.458,1.323 0.313,0.156 10 false C 0.635,1.292 0.833,1.458 0.198,0.167 10 true C 2.188,1.073 2.5,1.26 0.313,0.188 10 false A 2.198,1.5 2.51,1.688 0.313,0.188 10 false A 2.208,2.875 2.521,3.063 0.313,0.188 10 false B 2.198,2.458 2.385,2.604 0.188,0.146 10 false B 4.167,0.417 4.573,0.583 0.406,0.167 10 false A - A 5.938,0.417 6.344,0.583 0.406,0.167 10 false B - B 4.135,2.083 4.542,2.25 0.406,0.167 10 false C - C 4.083,1.063 4.396,1.25 0.313,0.188 10 false a 5.854,1.063 6.167,1.25 0.313,0.188 10 false a 5.104,2.271 5.417,2.458 0.313,0.188 10 false b 5.844,2.573 6.156,2.76 0.313,0.188 10 false c
*a Back Side *b Primer G


Standard Dimension:
Area Dimension Area Dimension
a 11.0 mm (0.433 in.) or more b 48.2 mm (1.90 in.) or more
c 22.0 mm (0.866 in.) or more - -


NOTICE:
·

Do not apply too much primer G.

·

Allow the primer G coating to dry for 3 minutes or more.

·

Do not keep any of the opened primer G for later use.



HINT:
·

Apply primer G onto the ceramic notches.

·

If an area other than that specified is coated by accident, wipe off the primer with a clean piece of cloth before it dries.




d.

Apply adhesive to the back door glass.

Adhesive:

Toyota Genuine Windshield Glass Adhesive or equivalent


i.
B214800C29
1.198,0.448 1.792,0.667 true 0.802,1.635 0.604,1.938 true 0.76,1 1.021,1.26 0.26,0.26 10 false A 1.854,0.625 2.167,0.896 0.313,0.271 10 false *a 1.115,0.896 1.385,1.146 0.271,0.25 10 false A 0.531,0.646 0.802,0.875 0.271,0.229 10 false B 1.302,1.458 1.594,1.708 0.292,0.25 10 false B 0.49,1.948 0.802,2.146 0.313,0.198 10 false *b
*a Nozzle
*b Adhesive


Cut off the tip of the cartridge nozzle as shown in the illustration.

Standard Dimension:
Area Dimension
A 12.0 mm (0.472 in.)
B 8.0 mm (0.315 in.)


HINT:

After cutting off the tip, use all adhesive within the time described in the table below.


Usage Time Frame:
Temperature Usage Time Frame
35°C (95°F) 15 minutes
20°C (68°F) 1 hour and 40 minutes
5°C (41°F) 8 hours



ii.

Load the sealer gun with the cartridge.


iii.

Apply adhesive to the back door glass as shown in the illustration.

B348249
0.052,0.042 0.365,0.198 0.313,0.156 10 false *a 0.375,3.531 0.688,3.688 0.313,0.156 10 false : *b 2.25,1.073 2.552,1.24 0.302,0.167 10 false A 2.271,1.479 2.573,1.646 0.302,0.167 10 false A 0.198,1.156 0.5,1.323 0.302,0.167 10 false C 0.688,1.302 0.865,1.458 0.177,0.156 10 true C 2.24,2.448 2.542,2.615 0.302,0.167 10 false B 2.25,2.854 2.552,3.021 0.302,0.167 10 false B 3.99,0.25 4.5,0.417 0.51,0.167 10 false A - A 5.823,0.25 6.333,0.417 0.51,0.167 10 false B - B 4.01,2 4.521,2.167 0.51,0.167 10 false C - C 3.958,0.771 4.24,0.938 0.281,0.167 10 false a 5.792,0.885 6.073,1.052 0.281,0.167 10 false a 5.198,2.24 5.479,2.406 0.281,0.167 10 false c 5.125,2.5 5.406,2.667 0.281,0.167 10 false b
*a Back Side *b Adhesive


Standard Dimension:
Area Dimension Area Dimension
a 15.2 mm (0.598 in.) b 55.2 mm (2.17 in.)
c 63.2 mm (2.49 in.) - -




e.

Install the back door glass.

i.
B349478
2.115,1.719 1.615,1.438 1.615,1.438 1.99,1.458 true 1.448,1.323 1.781,1.521 0.333,0.198 10 false *a
*a Matchmarks


Using suction cups, position the back door glass so that the matchmarks are aligned, and press it in gently along the rim.


ii.

Lightly press the front surface of the back door glass to ensure a close fit.

HINT:

Press the back doow glass with force of 98 N (10 kgf, 22.0 lbf) or more.



iii.

Using a scraper, remove any excess or protruding adhesive.


iv.

Hold the back door glass using protective tape until the applied adhesive becomes hard.

NOTICE:

Do not drive the vehicle for the time described in the table below.


Minimum Time:
Temperature Minimum Time Prior to Driving Vehicle
35°C (95°F) 1 hour and 30 minutes
20°C (68°F) 5 hours
5°C (41°F) 24 hours




f.

Connect each connector.


g.

Clean the contact surface of the vehicle body with a piece of cloth saturated with cleaner.


Hide 6.INSPECT FOR LEAK AND REPAIR

a.

After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.


b.

If water leaks into the cabin, allow the water to dry and add adhesive.


c.

Remove the protective tape.


Hide 8.INSTALL REAR WIPER ARM AND BLADE ASSEMBLY

Hide 85292A 9.INSTALL REAR WIPER ARM HEAD CAP