Home › Engine / Hybrid System › 1NZ-FE ENGINE MECHANICAL › CYLINDER BLOCK › 2015.01–2016.10
RM30M0E _51 Engine / Hybrid System _017073 1NZ-FE ENGINE MECHANICAL _0091009 CYLINDER BLOCK G

1NZ-FE ENGINE MECHANICAL  CYLINDER BLOCK  INSPECTION  


PROCEDURE

Hide 1.INSPECT CYLINDER BLOCK FOR WARPAGE

A105860C01
2.094,0.385 1.719,0.229 false 1.479,0.146 1.792,0.302 0.313,0.156 10 false *a
*a Straightedge


a.

Using a precision straightedge and feeler gauge, measure the warpage of the surface which is in contact with the cylinder head gasket.

Maximum warpage:

0.05 mm (0.0020 in.)


If the warpage is greater than the maximum, replace the cylinder block sub-assembly.


Hide 2.INSPECT CYLINDER BORE

a.

Visually inspect the surface of the cylinder walls to make sure there are no scratches, etc.

If there are scratches, etc. on the cylinder walls, replace the cylinder block sub-assembly.


b.
A105861C01
1.656,2.677 2.063,2.448 true 1.875,2.792 2.125,3.094 true 2.146,2.323 2.458,2.479 0.313,0.156 10 false *a 2.188,3.094 2.5,3.25 0.313,0.156 10 false *b 2.323,3.948 2.635,4.104 0.313,0.156 10 false *c 1.615,3.958 1.771,4.156 0.156,0.198 10 false B 1.615,3.615 1.771,3.813 0.156,0.198 10 false A 2.417,3.542 2.917,3.729 0.5,0.188 10 false 10 mm 2.438,3.708 3.188,3.885 0.75,0.177 10 false (0.3937 in.)
*a Thrust Direction
*b Axial Direction
*c Center
V100135

Engine Front


Using a cylinder gauge, measure the cylinder bore diameter at positions A and B in the thrust and axial directions.

Reference value (New parts) inside diameter:

75.000 to 75.013 mm (2.9528 to 2.9533 in.)


Maximum inside diameter:

75.133 mm (2.9580 in.)


If the inside diameter is greater than the maximum, replace the cylinder block sub-assembly


Hide 13101 3.INSPECT PISTON WITH PIN SUB-ASSEMBLY

A302035E01
0.104,1.698 1.344,1.875 1.24,0.177 10 false 27.6 to 27.8 mm

a.

Using a micrometer, measure the piston diameter at a right angle to the piston pin center line, and at the position 27.6 to 27.8 mm (1.0866 to 1.0945 in.) from top of the piston head.

Reference value (New parts) piston diameter:

74.935 to 74.945 mm (2.9502 to 2.9506 in.)



b.

Using a caliper gauge, measure the piston pin hole diameter.

Reference value (New parts) piston pin hole diameter:

18.013 to 18.016 mm (0.7092 to 0.7093 in.) at 20°C (68°F)



c.
A302036

Using a micrometer, measure the piston pin diameter.

Reference value (New parts) piston pin diameter:

18.001 to 18.004 mm (0.7087 to 0.7088 in.)



d.

Subtract the piston pin diameter measurement from the piston pin hole diameter measurement to calculate the oil clearance.

Reference value (New parts) oil clearance:

0.009 to 0.015 mm (0.0004 to 0.0006 in.)


Maximum oil clearance:

0.050 mm (0.0020 in.)


If necessary, replace the piston with pin sub-assembly.


Hide 4.INSPECT PISTON CLEARANCE

a.

Subtract the piston diameter measurement from the cylinder bore diameter measurement to calculate the oil clearance.

Reference value (New parts) oil clearance:

0.055 to 0.078 mm (0.0022 to 0.0031 in.)


Maximum oil clearance:

0.08 mm (0.0032 in.)


If the piston oil clearance is greater than the maximum, calculate the oil clearance using the measured cylinder internal diameter and piston external diameter as well as the reference diameters (for new parts), and replace the piston with pin sub-assembly or cylinder block sub-assembly.


Hide 5.INSPECT RING GROOVE CLEARANCE

A302037

a.

Using a feeler gauge, measure the clearance between the piston ring set and wall of the ring groove.

Ring groove clearance:
No. 1 compression ring:

0.03 to 0.07 mm (0.0012 to 0.0028 in.)

No. 2 compression ring:

0.02 to 0.06 mm (0.0008 to 0.0024 in.)

Oil ring:

0.07 to 0.13 mm (0.0028 to 0.0052 in.)


If the ring groove clearance is not as specified, replace the piston ring set. If the ring groove clearance is still not as specified even with a new piston ring set, replace the piston with pin sub-assembly.


Hide 6.INSPECT PISTON RING END GAP

A302038E01
0.469,1.427 1.052,1.594 0.583,0.167 10 false 110 mm

a.

Using a piston, push the piston ring, a little beyond the bottom of the ring travel, 110 mm (4.33 in.) from the top of the cylinder block sub-assembly.


b.
A302039

Using a feeler gauge, measure the end gap.

Standard end gap:
No. 1 compression ring:

0.18 to 0.23 mm (0.0071 to 0.0091 in.)

No. 2 compression ring:

0.37 to 0.47 mm (0.0146 to 0.0185 in.)

Oil ring (Side rail):

0.10 to 0.35 mm (0.0039 to 0.0138 in.)


Maximum end gap:
No. 1 compression ring:

0.86 mm (0.0339 in.)

No. 2 compression ring:

1.03 mm (0.0406 in.)

Oil ring (Side rail):

0.82 mm (0.0323 in.)


If the piston ring end gap is greater than the maximum, replace the piston ring set. If the piston ring end gap is greater than the maximum, even with a new piston ring set, replace the cylinder block sub-assembly.


Hide 13411 7.INSPECT CRANKSHAFT

A302041

a.

Using a dial indicator and V-blocks, measure the circle runout as shown in the illustration.

Maximum circle runout:

0.03 mm (0.0012 in.)


If the circle runout is greater than the maximum, replace the crankshaft.


b.
A302042

Using a micrometer, measure the diameter of each main journal.

Outside diameter:

45.988 to 46.000 mm (1.8106 to 1.8110 in.)


If the diameter is not as specified, check the crankshaft oil clearance.


c.

Check each main journal for taper and out-of-roundness as shown.

Maximum taper and out-of-roundness:

0.02 mm (0.0008 in.)


If the taper and out-of-roundness are greater than the maximum, replace the crankshaft.


d.
A302043

Using a micrometer, measure the diameter of each crank pin.

Outside diameter:

39.992 to 40.000 mm (1.5745 to 1.5748 in.)


If the diameter is not as specified, check the connecting rod oil clearance.


e.

Check each crank pin for taper and out-of-roundness as shown.

Maximum taper and out-of-roundness:

0.02 mm (0.0008 in.)


If the taper and out-of-roundness are greater than the maximum, replace the crankshaft.


f.
A302044

Wrap the chain sub-assembly around the timing sprocket.


g.

Using a vernier caliper, measure the timing sprocket diameter with the chain sub-assembly.

Standard sprocket diameter (with chain):

51.72 mm (2.0362 in.)


Minimum sprocket diameter (with chain):

50.5 mm (1.988 in.)


NOTICE:

Make sure that the vernier caliper is in contact with the chain rollers when measuring.


If the diameter is less than the minimum, replace the chain sub-assembly and crankshaft.


Hide 13265 8.INSPECT CONNECTING ROD BOLT

A302040

a.

Using a vernier caliper, measure the diameter of the connecting rod bolt at the elongated portion.

Standard diameter:

6.6 to 6.7 mm (0.260 to 0.264 in.)


Minimum diameter:

6.4 mm (0.252 in.)


If the diameter is less than the minimum, replace the connecting rod bolt.


Hide 11416 9.INSPECT CRANKSHAFT BEARING CAP SET BOLT

A302045

a.

Using a vernier caliper, measure the tension portion diameter at the elongated portion.

Standard diameter:

7.3 to 7.5 mm (0.287 to 0.295 in.)


Minimum diameter:

7.2 mm (0.283 in.)


If the diameter is less than minimum, replace the crankshaft bearing cap set bolt.


Hide 10.INSPECT CONNECTING ROD THRUST CLEARANCE

A302027

a.

Using a dial indicator, measure the thrust clearance while moving the connecting rod back and forth.

Standard thrust clearance:

0.16 to 0.36 mm (0.0063 to 0.0142 in.)


Maximum thrust clearance:

0.36 mm (0.0142 in.)


If the thrust clearance is greater than the maximum, replace the connecting rod sub-assembly as necessary. If necessary, replace the crankshaft.


Hide 11.INSPECT CONNECTING ROD OIL CLEARANCE

a.

Check that the matchmarks on the connecting rod and connecting rod cap are aligned to ensure correct reassembly.


b.
A107302E01
0.382,0.261 0.698,0.437 0.316,0.177 10 SST 0.776,0.382 1.674,0.557 false

Using SST, remove the 2 connecting rod bolts.

SST
09205-16011  


c.

Clean the crank pin and connecting rod bearing.


d.

Check the crank pin and connecting rod bearing for pitting and scratches.


e.
A302028C01
1.615,0.823 0.781,0.313 true 0.625,0.219 0.813,0.406 0.188,0.188 10 false *a
*a Plastigage


Lay a strip of Plastigage across the crank pin.


f.
A302029C01
1.365,0.885 0.76,0.333 true 0.594,0.229 0.802,0.385 0.208,0.156 10 false *a
*a Front Mark


Make sure that the connecting rod and connecting rod cap are in the correct combination and that the front mark on the connecting rod cap is facing in the correct mounting orientation, then install the connecting rod cap to the connecting rod.


g.

Apply a light coat of engine oil to the threads of the connecting rod bolts.


h.
A151606E02
1.635,0.396 0.865,0.323 false 0.552,0.25 1.135,0.448 0.583,0.198 10 false SST

Using SST, tighten the 2 connecting rod bolts in several steps to the specified torque.

SST
09205-16011  

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)


i.
A302031C05
2.26,0.51 2.646,0.25 true 2.688,0.177 2.927,0.354 0.24,0.177 10 false *a 1.177,0.24 1.417,0.417 0.24,0.177 10 false 90°
*a Paint Mark
V100136

Engine Front


Mark the front of the connecting rod bolts with paint.


j.

Further tighten the connecting rod bolts by 90° as shown in the illustration.

NOTICE:

Do not turn the crankshaft.



k.

Remove the 2 connecting rod bolts, connecting rod cap and connecting rod bearing.


l.
A302032C01
1.552,0.865 0.781,0.219 true 0.625,0.125 0.938,0.281 0.313,0.156 10 false *a
*a Plastigage


Measure the Plastigage at its widest point.

Standard oil clearance:

0.012 to 0.038 mm (0.00047 to 0.0015 in.)


NOTICE:

Completely remove the Plastigage after the measurement.



m.
A302033C01
2.479,1.458 2.479,1.76 false 0.552,0.635 0.552,1.656 true 1.594,1.333 0.563,1.333 true 0.49,1.667 0.719,1.854 0.229,0.188 10 false *a 2.417,1.781 2.646,1.958 0.229,0.177 10 false *b
*a Mark 1, 2 or 3
*b Front Mark


When replacing a connecting rod bearing, replace it with one with the same number as marked on the connecting rod. There are 3 sizes of standard connecting rod bearings, marked 1, 2 and 3 accordingly.

Standard Bearing Center Wall Thickness
Mark mm (in.)
1 1.491 to 1.494 (0.0587 to 0.0588)
2 1.494 to 1.497 (0.0588 to 0.0589)
3 1.497 to 1.500 (0.0589 to 0.0591)


Hide 12.INSPECT CRANKSHAFT THRUST CLEARANCE

A302034

a.

Using a dial indicator, measure the thrust clearance while moving the crankshaft back and forth with a screwdriver.

Standard thrust clearance:

0.09 to 0.19 mm (0.0035 to 0.0075 in.)


Maximum thrust clearance:

0.30 mm (0.0118 in.)


HINT:

Upper crankshaft thrust washer thickness: 2.43 to 2.48 mm (0.0957 to 0.976 in.)


If the thrust clearance is greater than the maximum, replace the upper crankshaft thrust washers as a set. Check the crankshaft and cylinder block sub-assembly for wear. Repair or replace the parts if necessary.


Hide 13.INSPECT CRANKSHAFT OIL CLEARANCE

a.

Clean each main journal and crankshaft bearing.


b.

Install the crankshaft bearing to the cylinder block sub-assembly and crankshaft bearing cap.

Click hereEngine / Hybrid System>1NZ-FE ENGINE MECHANICAL>CYLINDER BLOCK>REASSEMBLY


c.

Place the crankshaft to the cylinder block sub-assembly.


d.
A302046C01
1.583,1.177 0.76,0.219 true 0.604,0.125 0.802,0.281 0.198,0.156 10 false *a
*a Plastigage


Lay a strip of Plastigage across each journal.


e.
A267077C07
0.688,0.813 0.885,0.49 true 1.021,0.969 1.344,0.708 true 2.344,0.823 2.542,0.5 true 0.927,0.365 1.094,0.521 0.167,0.156 10 false *a 2.604,0.375 2.771,0.531 0.167,0.156 10 false *c 1.427,0.615 1.604,0.771 0.177,0.156 10 false *b 0.063,0.083 0.26,0.24 0.198,0.156 10 false *1 1.844,0.063 2.021,0.219 0.177,0.156 10 false *2
*1 No. 3 Crankshaft Bearing Cap
*2 No. 1, 2, 4, 5 Crankshaft Bearing Cap
*a Front Mark
*b Number
*c Front Mark and Number


Examine the front marks and numbers and install the crankshaft bearing cap to the cylinder block sub-assembly.


f.

Apply a light coat of engine oil to the threads of the crankshaft bearing cap set bolts.


g.
A302806E02
1.563,0.406 1.75,0.573 0.188,0.167 10 true 1 0.958,0.396 1.167,0.552 0.208,0.156 10 true 5 0.26,0.375 0.469,0.552 0.208,0.177 10 true 9 2.813,0.417 3.021,0.594 0.208,0.177 10 true 7 2.198,0.385 2.406,0.563 0.208,0.177 10 true 3 1.573,1.677 1.729,1.865 0.156,0.188 10 true 2 0.927,1.656 1.083,1.844 0.156,0.188 10 true 6 0.271,1.656 0.479,1.844 0.208,0.188 10 true 10 2.833,1.656 3.042,1.844 0.208,0.188 10 true 8 2.208,1.667 2.417,1.854 0.208,0.188 10 true 4

Using a 12 mm socket wrench, tighten the crankshaft bearing cap set bolts in several steps to the specified torque in the sequence shown in the illustration. (*1)

Torque:
22 N*m (224 kgf*cm, 16 ft.*lbf)


h.
A302031C05
2.26,0.51 2.646,0.25 true 2.688,0.177 2.927,0.354 0.24,0.177 10 false *a 1.177,0.24 1.417,0.417 0.24,0.177 10 false 90°
*a Paint Mark
V100136

Engine Front


Mark the front of the crankshaft bearing cap set bolts with paint.


i.

Further tighten the crankshaft bearing cap set bolts by 90° in the same sequence as step (*1).


j.

Check that the painted mark is now at a 90° angle from the front.

NOTICE:

Do not turn the crankshaft.



k.

Remove the crankshaft bearing caps.


l.
A302048C02
1.656,1.135 0.792,0.188 true 0.625,0.104 0.813,0.25 0.188,0.146 10 false *a
*a Plastigage


Measure the Plastigage at its widest point.

Standard oil clearance:

0.01 to 0.023 mm (0.0004 to 0.0009 in.)


Maximum oil clearance:

0.07 mm (0.0028 in.)


NOTICE:

Completely remove the Plastigage after the measurement.



m.
A302809C01
0.469,1.385 0.781,1.688 true 0.521,3.719 0.208,3.875 0.208,3.875 0.521,3.156 true 1.063,1.344 0.875,1.688 true 0.521,1.813 0.771,1.813 true 0.49,2.115 0.781,1.938 true 0.885,1.823 1.135,1.823 true 2.115,1.333 2.208,1.604 true 2.125,1.844 2.302,1.656 true 2.51,1.344 2.385,1.615 true 2.479,1.667 2.573,1.927 true 2.771,1.51 2.583,1.604 true 0.052,3.844 0.365,4 0.313,0.156 10 false *a 0.083,1.292 0.479,1.458 0.396,0.167 10 true No. 1 1.125,1.25 1.521,1.417 0.396,0.167 10 true No. 2 0.094,1.708 0.49,1.875 0.396,0.167 10 true No. 3 0.094,2.031 0.49,2.198 0.396,0.167 10 true No. 5 1.177,1.729 1.573,1.896 0.396,0.167 10 true No. 4 1.75,1.25 2.146,1.417 0.396,0.167 10 true No. 1 1.74,1.771 2.135,1.938 0.396,0.167 10 true No. 2 2.573,1.25 2.969,1.417 0.396,0.167 10 true No. 3 2.635,1.906 3.031,2.073 0.396,0.167 10 true No. 4 2.823,1.427 3.219,1.594 0.396,0.167 10 true No. 5
*a Mark


When replacing a standard bearing, replace it with one with the same number. If the number of the bearing cannot be found, select the correct bearing by adding together the numbers imprinted on the cylinder block sub-assembly and crankshaft, then select the bearing with the same number as the total. There are 4 sizes of standard bearings, marked 1, 2, 3 and 4 accordingly.

EXAMPLE: Cylinder Block 4 (A) + Crankshaft 3 (B) = Total 7 (Use Bearing 3)
Cylinder Block (A)
+
Crankshaft (B)
0 to 2 3 to 5 6 to 8 9 to 11
Use Bearing 1 2 3 4

Item Mark mm (in.)
Cylinder block main journal bore diameter (A) 0
1
2
3
4
5
6
50.000 to 50.003 (1.96850 to 1.96862)
50.003 to 50.005 (1.96862 to 1.96870)
50.005 to 50.007 (1.96870 to 1.96878)
50.007 to 50.010 (1.96878 to 1.96890)
50.010 to 50.012 (1.96890 to 1.96898)
50.012 to 50.014 (1.96898 to 1.96906)
50.014 to 50.016 (1.96906 to 1.96913)
Crankshaft main journal diameter (B) 0
1
2
3
4
5
45.998 to 46.000 (1.81094 to 1.81102)
45.996 to 45.998 (1.81087 to 1.81094)
45.994 to 45.996 (1.81079 to 1.81087)
45.992 to 45.994 (1.81071 to 1.81079)
45.990 to 45.992 (1.81063 to 1.81071)
45.988 to 45.990 (1.81055 to 1.81063)
Standard bearing center wall thickness 1
2
3
4
1.992 to 1.995 (0.07843 to 0.07854)
1.995 to 1.998 (0.07854 to 0.07866)
1.998 to 2.001 (0.07866 to 0.07878)
2.001 to 2.004 (0.07878 to 0.07890)