DATA LIST
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
In accordance with the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Vehicle Speed | Vehicle speed | Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph) |
Actual vehicle speed | ·
This is the current vehicle speed. ·
The vehicle speed is detected using the wheel speed sensors. ·
Vehicle speed data is delayed when it is displayed. Therefore, even if the vehicle speed listed in the freeze frame data is 0 km/h (0 mph), this does not always mean that the malfunction occurred when the vehicle was stopped. |
| Engine Speed | Engine speed | Min.: 0 rpm
Max.: 16383 rpm |
600 to 700 rpm: Idling | When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed. |
| MAF | Airflow rate from mass air flow meter | Min.: 0 gm/sec.
Max.: 655.35 gm/sec. |
·
1.0 to 3.0 gm/sec: Idling with warm engine (A/C off and shift lever in N) ·
3.0 to 9.0 gm/sec: 3000 rpm (A/C off and shift lever in N) |
This is the intake air amount from the mass air flow meter. |
| Coolant Temp | Engine coolant temperature | Min.: -40°C (-40°F)
Max.: 140°C (284°F) |
75 to 100°C (167 to 212°F): After warming up | This is the engine coolant temperature.
|
| Throttle Motor DUTY | Throttle actuator | Min.: 0%
Max.: 100% |
10 to 22%: Idling(A/C off and shift lever in N) | This is the out put duty ratio of the throttle actuator drive circuit. |
| N Range Status | Judgment for shift lever N position | ON or OFF | ·
OFF: Shift lever not in N ·
ON: Shift lever in N |
- |
| Starter Signal | Starter signal | OFF or ON | ·
ON: Starter operating ·
OFF: Starter not operating |
- |
| Neutral Position SW Signal | Park/neutral position switch status | ON or OFF | ·
ON: Shift lever in P or N ·
OFF: Shift lever not in P or N |
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect. |
| Stop Light Switch | Stop light switch status | ON or OFF | ·
ON: Brake pedal depressed ·
OFF: Brake pedal released |
- |
| A/C Signal | A/C switch status | OFF or ON | ON: A/C switch on | - |
| Closed Throttle Position SW | Closed throttle position switch status | OFF or ON | ·
ON: Throttle fully closed ·
OFF: Throttle open |
- |
| TC and TE1 | TC and CG (TE1) terminals of DLC3 | OFF or ON | - | - |
| SPD (NT) | Input turbine speed | Min.: 0 rpm
Max.: 12750 rpm |
·
Lock-up on (After warming up engine): Input turbine speed (NT) equal to engine speed ·
Lock-up off (Idling with shift lever in P or N): Input turbine speed (NT) nearly equal to engine speed ·
Vehicle stopped with shift lever in R: 0 rpm |
Data is displayed in increments of 50 rpm. |
| Shift SW Status (P Range) | Park/neutral position switch status | ON or OFF | ·
ON: Shift lever in P ·
OFF: Shift lever not in P |
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
|
| Shift SW Status (R Range) | Park/neutral position switch status | ON or OFF | ·
ON: Shift lever in R ·
OFF: Shift lever not in R |
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
|
| Shift SW Status (N Range) | Park/neutral position switch status | ON or OFF | ·
ON: Shift lever in N ·
OFF: Shift lever not in N |
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
|
| Shift SW Status (N,P Range) Supported | Status of Park/neutral position switch (N or P) support | Supp or Unsupp | - | - |
| Shift SW Status (N,P Range) | Park/neutral position switch status | ON or OFF | ·
ON: Shift lever in P or N ·
OFF: Shift lever not in P or N |
- |
| Sports Shift Up SW | Sport shift up switch status | OFF or ON | ·
ON: Shift lever held in "+" ·
OFF: Shift lever not held in "+" |
- |
| Sports Shift Down SW | Sport shift down switch status | OFF or ON | ·
ON: Shift lever held in "-" ·
OFF: Shift lever not held in "-" |
- |
| Sports Mode Selection SW | Sport mode select switch status | OFF or ON | ·
ON: Shift lever in M, "+" or "-" ·
OFF: Shift lever not in M, "+" or "-" |
- |
| Shift SW Status (D Range) | Park/neutral position switch status | ON or OFF | ·
ON: Shift lever in D or M ·
OFF: Shift lever not in D or M |
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect. |
| A/T Oil Temperature 1 | CVT fluid temperature sensor value | Min.: -40°C (-40°F)
Max.: 150°C (302°F) |
·
After stall speed test: Approximately 100°C (212°F) ·
Equal to ambient temperature after cold soak |
If the value is -40°C (-40°F) or 150°C (302°F) or higher, the CVT fluid temperature sensor circuit is open or shorted. |
| NT Sensor Voltage | Input turbine speed (NT) sensor output voltage | Min.: 0 V
Max.: 4.999 V |
Engine idling (Vehicle stopped with shift lever in P or N): 0.6 to 1.5 V | - |
| SPD (NIN) | Primary pulley speed (NIN) | Min.: 0 rpm
Max.: 12750 rpm |
·
Vehicle stopped: 0 rpm ·
Lock-up on (After warming up engine): Primary pulley speed (NIN) equal to engine speed |
Data is displayed in increments of 50 rpm. |
| SPD (NOUT) | Secondary pulley speed (NOUT) | Min.: 0 rpm
Max.: 12750 rpm |
·
Vehicle stopped: 0 rpm ·
Vehicle cruising at approximately 60 km/h (37 mph): 2975 rpm |
Data is displayed in increments of 50 rpm. |
| NOUT Sensor Voltage | Secondary pulley speed (NOUT) sensor output voltage | Min.: 0.000 V
Max.: 4.999 V |
Engine idling: Approximately 2 V | - |
| A/T Oil Pressure | Secondary oil pressure value | Min.: -64 MPa
Max.: 63.998 MPa |
Secondary oil pressure inspection
·
D position stall speed test: 4.4 to 6.5 MPa ·
R position stall speed test: 4.4 to 6.8 MPa |
- |
| G Sensor | Converted output voltage of deceleration sensor | Min.: 0 V
Max.: 79.998 V |
Displays converted voltage of deceleration sensor
·
Vehicle on level ground: 2.31 V to 2.69 V ·
Decelerating: 1.88 V to 2.5 V ·
Accelerating: 2.5 V to 3.11 V ·
G sensor malfunction: Set to 1.87 V ·
Communication malfunction: Set to 1.87 V |
- |
| Lock Up | Lock-up | ON or OFF | ·
ON: Lock-up operating ·
OFF: Lock-up not operating |
- |
| Shift Status | ECM gearshift command | 1st, 2nd, 3rd, 4th or 5th | Same as actual gear | *2 |
| Solenoid (DS2) | Shift solenoid valve DS2 status | ON or OFF | ·
OFF: Constant cruising with shift lever in D ·
ON: Accelerator pedal depressed further after cruising with shift lever in D |
- |
| Solenoid (DS1) | Shift solenoid valve DS1 status | ON or OFF | ·
ON: Driving with shift lever in D and accelerator pedal depressed ·
OFF: Accelerator pedal released when driving with shift lever in D with accelerator pedal depressed |
- |
| Solenoid (SLS) | Shift solenoid valve SLS status | ON or OFF | ·
ON: After engine start ·
OFF: Ignition switch ON |
- |
| SLT Solenoid Status | Shift solenoid valve SLT status | ON or OFF | ·
ON: After engine start ·
OFF: Ignition switch ON |
- |
| SLU Solenoid Status | Shift solenoid valve SLU status | ON or OFF | ·
ON: Lock up operating ·
OFF: Lock up not operating |
- |
| G Sensor Calibration | G sensor calibration status | Incomplete or Complete | Complete | - |
| G Sensor Learning Value | G sensor learned value voltage | Min.: 0 V
Max.: 79.998 V |
G sensor calibration is complete: 2.31 V to 2.69 V | - |
| CVT Oil Press Calibration | CVT oil pressure calibration status | Incomplete or Complete | Complete | - |
*1: Refer to DTC P0705.
Click hereDrivetrain>K411 CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>P0705
*2: "Shift Status" is a signal divided into 5 gear positions for Active Test.
It does not express gear ratios for normal driving or gear positions for 7-speed sport sequential shiftmatic mode.
ACTIVE TEST
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
In accordance with the display on the GTS, perform the Active Test.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Connect the TC and TE1 | Turn on and off TC and TE1 connection | ON or OFF | ·
ON: TC and TE1 are connected. ·
OFF: TC and TE1 are disconnected. [Vehicle Condition] Perform with the ignition switch ON, the engine stopped and shift lever in P. |
| Activate the Solenoid (SLU) | Operate shift solenoid valve SLU | ON or OFF | [Vehicle Condition]
Perform with the ignition switch ON, the engine stopped and shift lever in P or N. |
| Activate the Solenoid (SLT) | Operate shift solenoid valve SLT | ON or OFF | [Vehicle Condition]
Perform with the ignition switch ON and the engine running. |
| Activate the Lock Up | Operate lock-up | ON or OFF | Possible to check lock-up operation.
[Vehicle Condition] Perform at a vehicle speed of 60 km/h (37 mph) or more. |
| Control the Shift Position | Operate the shift solenoid valves to allow the gear ratio to be manually selected [1st (gear ratio max.) - 2nd - 3rd - 4th - 5th (gear ratio min.)] | ·
Press "→" button: Shift up ·
Press "←" button: Shift down |
Used to check the operation of the shift solenoid valves.
[Vehicle Condition] Perform at a vehicle speed of 20 km/h (12 mph) or more and 45 km/h (28 mph) or less. |
| Activate the Solenoid (DS1) | Operate shift solenoid valve DS1 | ON or OFF | [Vehicle Condition]
Perform with the ignition switch ON, the engine stopped and shift lever in P or N. |
| Activate the Solenoid (DS2) | Operate shift solenoid valve DS2 | ON or OFF | [Vehicle Condition]
Perform with the ignition switch ON, the engine stopped and shift lever in P or N. |
| Control the SLS Pressure | Operate shift solenoid valve SLS | High or Low | [Vehicle Condition]
Perform with the ignition switch ON and the engine running. |
| Activate the Solenoid (SLS) | Operate shift solenoid valve SLS | ON or OFF | [Vehicle Condition]
Perform with the ignition switch ON, the engine stopped and shift lever in P or N. |