The park/neutral position switch and transmission control switch (shift lock control unit assembly) detect the shift lever position and send signals to the ECM.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0705 | Transmission Range Sensor Circuit Malfunction (PRNDL Input) | When the ignition switch is ON and the battery voltage is 10.5 V or more, any one of the following conditions is met (2 trip detection logic):
·
2 or more signals are ON simultaneously for 2 seconds or more for (NSW, P, N), R, D input signals. ·
NSW, P, R, N, D input signals are all OFF simultaneously for 60 seconds or more. ·
When the S signal (M position switch signal) is ON, any of the NSW, P, R, N input signals is ON simultaneously for 2 seconds or more. |
·
Open or short in park/neutral position switch circuit ·
Park/neutral position switch ·
Transmission control switch (Shift lock control unit assembly) ·
ECM |
Comes on | DTC stored |
For safety, the park/neutral position switch detects the gearshift position so that engine can be started only when the vehicle is in the P or N shift position.
When the park/neutral position switch and shift lock control unit assembly (transmission control switch) send more than one signal at a time from switch positions P, R, N, D, M, the ECM interprets this as a fault in the switch. The ECM will turn on the MIL and store the DTC.
Perform initialization after replacing any parts related to the continuously variable transaxle system.
Click hereDrivetrain>K411 CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION
Check that no DTCs are stored after performing initialization.
Click hereDrivetrain>K411 CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
Inspect the fuses for circuits related to this system before performing the following procedure.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
| Tester Display |
|---|
| Neutral Position SW Signal |
| Shift SW Status (P Range) |
| Shift SW Status (R Range) |
| Shift SW Status (N Range) |
| Shift SW Status (D Range) |
In accordance with the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Neutral Position SW Signal | Park/neutral position switch status | ON or OFF | ·
ON: Shift lever in P or N ·
OFF: Shift lever not in P or N |
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect. |
| Shift SW Status (P Range) | Park/neutral position switch status | ON or OFF | ·
ON: Shift lever in P ·
OFF: Shift lever not in P |
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect. |
| Shift SW Status (R Range) | Park/neutral position switch status | ON or OFF | ·
ON: Shift lever in R ·
OFF: Shift lever not in R |
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect. |
| Shift SW Status (N Range) | Park/neutral position switch status | ON or OFF | ·
ON: Shift lever in N ·
OFF: Shift lever not in N |
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect. |
| Shift SW Status (D Range) | Park/neutral position switch status | ON or OFF | ·
ON: Shift lever in D or M ·
OFF: Shift lever not in D or M |
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect. |
| Result | Proceed to |
|---|---|
| Data display is within Normal Condition range | A |
| Data display is not within Normal Condition range | B |
A
B
Enter the following menus: Powertrain / Engine and ECT / Data List.
| Tester Display |
|---|
| Sports Mode Selection SW |
In accordance with the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Sports Mode Selection SW | Transmission control switch status | ON or OFF | ·
ON: Shift lever in M, "+" or "-" ·
OFF: Shift lever not in M, "+" or "-" |
- |
| Result | Proceed to |
|---|---|
| Data display is within Normal Condition range | A |
| Data display is not within Normal Condition range | B |
A
B
| *a | Front view of wire harness connector
(to Shift Lock Control Unit Assembly (Transmission Control Switch)) |
Disconnect the shift lock control unit assembly (transmission control switch) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F133-4 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
| F133-5 (S) - Body ground | Ignition switch off | Below 1 V |
Connect the shift lock control unit assembly (transmission control switch) connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Shift Lock Control Unit Assembly (Transmission Control Switch)) |
Disconnect the F133 shift lock control unit assembly (transmission control switch) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 4 (IG) - 5 (S) | Shift lever in M, "+" or "- " | Below 1 Ω |
| Shift lever not in M, "+" or "-" | 10 kΩ or higher |
Connect the F133 shift lock control unit assembly (transmission control switch) connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the B48 ECM connector.
Disconnect the F133 shift lock control unit assembly (transmission control switch) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F133-5 (S) - B48-30 (S) | Always | Below 1 Ω |
| F133-5 (S) - Body ground | Always | 10 kΩ or higher |
| B48-30 (S) - Body ground | Always | 10 kΩ or higher |
Connect the F133 shift lock control unit assembly (transmission control switch) connector.
Connect the B48 ECM connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Park/Neutral Position Switch) |
Disconnect the park/neutral position switch connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| B19-1 (RB) - Body ground | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V |
Connect the park/neutral position switch connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the B19 park/neutral position switch connector.
| *a | Component without harness connected
(Park/Neutral Position Switch) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 4 (B) - 9 (L) | Shift lever in P or N | Below 1 Ω |
| Shift lever not in P or N | 10 kΩ or higher | |
| 1 (RB) - 3 (PL) | Shift lever in P | Below 1 Ω |
| Shift lever not in P | 10 kΩ or higher | |
| 1 (RB) - 2 (RL) | Shift lever in R | Below 1 Ω |
| Shift lever not in R | 10 kΩ or higher | |
| 1 (RB) - 8 (NL) | Shift lever in N | Below 1 Ω |
| Shift lever not in N | 10 kΩ or higher | |
| 1 (RB) - 7 (DL) | Shift lever in D or M | Below 1 Ω |
| Shift lever not in D or M | 10 kΩ or higher |
Connect the B19 park/neutral position switch connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the B47, B48 and F130 ECM connectors.
Disconnect the B19 park/neutral position switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B19-3 (PL) - B48-25 (P) | Always | Below 1 Ω |
| B19-2 (RL) - F130-8 (R) | Always | Below 1 Ω |
| B19-8 (NL) - B48-24 (N) | Always | Below 1 Ω |
| B19-7 (DL) - F130-18 (D) | Always | Below 1 Ω |
| B19-4 (B) - B47-15 (NSW) | Always | Below 1 Ω |
| B19-3 (PL) or B48-25 (P) - Body ground and other terminals | Always | 10 kΩ or higher |
| B19-2 (RL) or F130-8 (R) - Body ground and other terminals | Always | 10 kΩ or higher |
| B19-8 (NL) or B48-24 (N) - Body ground and other terminals | Always | 10 kΩ or higher |
| B19-7 (DL) or F130-18 (D) - Body ground and other terminals | Always | 10 kΩ or higher |
| B19-4 (B) or B47-15 (NSW) - Body ground and other terminals | Always | 10 kΩ or higher |
Connect the B19 park/neutral position switch connector.
Connect the B47, B48 and F130 ECM connectors.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>1NR-FE ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT