Home › Drivetrain › K411 CVT › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › 2016.04–2016.07
RM30M0E _52 Drivetrain _052750 K411 CVT _0254682 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K411 CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P1585  Acceleration Sensor Circuit  


DESCRIPTION

The ECM determines the vehicle inclination based on a signal from the deceleration sensor. If a malfunction is determined in the deceleration sensor based on a malfunction signal from the brake actuator assembly (skid control ECU).

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1585 Acceleration Sensor Circuit After the ignition switch is turned ON, the brake actuator assembly (skid control ECU) has detected one of the following conditions, and the ECM has received a diagnostic signal from the brake actuator assembly (skid control ECU) for 3 seconds or more (1 trip detection logic).
·

Output value of the deceleration sensor remains below -1.5 G or more than 1.5 G for at least 1.2 seconds or more.

·

The deceleration sensor power source voltage is 4.4 V or less, or 5.6 V or higher, for at least 1.2 seconds or more.

·

No signal is detected from the deceleration sensor 7 times or more.


·

Wire harness or connector

·

Deceleration sensor

·

Brake actuator assembly (Skid control ECU)

·

CAN communication system


Does not come on DTC stored

WIRING DIAGRAM

C279809E21
0.385,1.896 1.688,2.083 1.302,0.188 10 false Deceleration Sensor 0.375,1.719 0.823,1.896 0.448,0.177 10 false F132 0.708,2.313 3.615,2.51 2.906,0.198 10 false : CAN Communication Line 1.302,0.583 1.635,0.76 0.333,0.177 10 false GL1 1.26,1.302 1.604,1.469 0.344,0.167 10 false VGS 2.438,1.698 3.5,1.896 1.063,0.198 10 false A47*1,A35*2 2.427,1.875 5.333,2.073 2.906,0.198 10 false Brake Actuator Assembly (Skid Control ECU) 5.823,1.688 6.229,1.896 0.406,0.208 10 false ECM 1.167,0.938 1.604,1.115 0.438,0.177 10 false GGND 3,0.563 3.333,0.74 0.333,0.177 10 false GL1 3,0.927 3.438,1.104 0.438,0.177 10 false GGND 3.01,1.281 3.354,1.448 0.344,0.167 10 false VGS 1.656,0.479 1.802,0.646 0.146,0.167 10 false 1 1.656,0.833 1.802,1 0.146,0.167 10 false 2 2.792,0.49 2.938,0.656 0.146,0.167 10 false 3 1.656,1.198 1.802,1.365 0.146,0.167 10 false 3 2.75,0.833 3.042,1 0.292,0.167 10 false 15 2.76,1.198 3.021,1.365 0.26,0.167 10 false 26 6,2.146 6.781,2.375 0.781,0.229 10 false *1:for LHD 6,2.438 6.74,2.688 0.74,0.25 10 false *2:for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

Perform initialization when parts related to the continuously variable transaxle are replaced.

Click hereDrivetrain>K411 CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K411 CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



HINT:

If a CAN communication DTC is output, perform troubleshooting for that DTC first.


PROCEDURE

1.CHECK DTC OUTPUT (CAN COMMUNICATION SYSTEM)
a.

Check for DTCs of the CAN communication system.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

2.READ VALUE USING GTS (G SENSOR)

B

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

2.READ VALUE USING GTS (G SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.


e.

In accordance with the display on the GTS, read the Data List.

Powertrain > Engine and ECT > Data List
Tester Display
G Sensor
50003 234 410
Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
G Sensor Converted output voltage of deceleration sensor Min.: 0 V
Max.: 79.998 V
Displays converted voltage of deceleration sensor
·

Vehicle on level ground: 2.31 V to 2.69 V

·

Decelerating: 1.88 V to 2.5 V

·

Accelerating: 2.5 V to 3.11 V

·

G sensor malfunction: Set to 1.87 V

·

Communication malfunction: Set to 1.87 V


-

Result:
Result Proceed to
Data displayed is as specified under Normal Condition A
Data displayed is not as specified under Normal Condition B



A

6.REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

B

3.CHECK HARNESS AND CONNECTOR (DECELERATION SENSOR - SKID CONTROL ECU)
3.CHECK HARNESS AND CONNECTOR (DECELERATION SENSOR - SKID CONTROL ECU)
a.

Disconnect the F132 deceleration sensor connector.


b.

Disconnect the A47*1,A35*2 brake actuator assembly (skid control ECU) connectors.


c.

Measure the resistance according to the value(s) in the table below.

*1:for LHD

*2:for RHD

Standard Resistance:
for: LHD
Tester Connection Condition Specified Condition
F132-1 (GL1) -A47-3 (GL1) Always Below 1 Ω
F132-2 (GGND) -A47-15 (GGND) Always Below 1 Ω
F132-3 (VGS) -A47-26 (VGS) Always Below 1 Ω
F132-1 (GL1) or A47-3 (GL1) -Body ground Always 10 kΩ or higher
F132-2 (GGND) or A47-15(GGND) - Body ground Always 10 kΩ or higher
F132-3 (VGS) or A47-26 (VGS) -Body ground Always 10 kΩ or higher


Standard Resistance:
for: RHD
Tester Connection Condition Specified Condition
F132-1 (GL1) -A35-3 (GL1) Always Below 1 Ω
F132-2 (GGND) -A35-15 (GGND) Always Below 1 Ω
F132-3 (VGS) -A35-26 (VGS) Always Below 1 Ω
F132-1 (GL1) or A35-3 (GL1) -Body ground Always 10 kΩ or higher
F132-2 (GGND) or A35-15(GGND) - Body ground Always 10 kΩ or higher
F132-3 (VGS) or A35-26 (VGS) -Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT DECELERATION SENSOR (POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT DECELERATION SENSOR (POWER SOURCE)
a.
C199166C08
0.479,1.031 0.906,1.323 0.427,0.292 1.906,1.229 2.177,1.813 true 0.115,0.104 0.427,0.302 0.313,0.198 10 false *a 2.063,1.865 2.479,2.094 0.417,0.229 10 false VGS 0.531,1.083 0.99,1.333 0.458,0.25 10 false F132
*a Front view of wire harness connector
(to Deceleration Sensor)


Disconnect the deceleration sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F132-3 (VGS) - Body ground Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

5.INSPECT DECELERATION SENSOR (GL1 VOLTAGE)

NG

6.REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)
5.INSPECT DECELERATION SENSOR (GL1 VOLTAGE)
a.
C277071C01
1.698,1.74 1.698,1.177 true 1.146,1.729 1.469,1.177 true 2.281,1.719 1.948,1.177 true 0.188,0.146 0.5,0.344 0.313,0.198 10 *a 0.927,1.813 1.375,2.021 0.448,0.208 10 VGS 1.49,1.813 2.031,2.042 0.542,0.229 10 GGND 2.25,1.813 2.688,2.063 0.438,0.25 10 GL1
*a Component without harness connected
(Deceleration Sensor)


Remove the deceleration sensor.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>DECELERATION SENSOR>REMOVAL


b.

Connect 3 dry cell batteries of 1.5 V in series.


c.

Connect the positive (+) lead of the batteries to terminal 3 (VGS) and the negative (-) lead to terminal 2 (GGND) to apply a voltage of 4.5 V.

NOTICE:
·

Do not apply 6 V or higher to terminals 3 (VGS) and 2 (GGND).

·

If the sensor is dropped, replace it with a new one.




d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1 (GL1) - 2 (GGND)
·

4.5 V applied to terminals 3 (VGS) and 2 (GGND)

·

Sensor not tilted


Approximately 2.5 V
1 (GL1) - 2 (GGND)
·

4.5 V applied to terminals 3 (VGS) and 2 (GGND)

·

Sensor tilted back and forth


Changes between approximately 0.5 V and 4.5 V


HINT:

If the sensor is tilted too much, it may output the wrong value.



Result:
Proceed to
OK
NG



OK

6.REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

NG

7.REPLACE DECELERATION SENSOR
6.REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)
a.

Replace the brake actuator assembly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.REPLACE DECELERATION SENSOR

Result:
Proceed to
NEXT



NEXT