After moving the shift lever to M, it is possible to change the shift range between M1 and M7 using the shift lever. Moving the shift lever to "+" once raises the shift range by one, and moving the shift lever to "-" lowers the shift range by one.
Perform initialization after replacing any parts related to the continuously variable transaxle system.
Click hereDrivetrain>K411 CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION
Check that no DTCs are stored after performing initialization.
Click hereDrivetrain>K411 CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
Inspect the fuses for circuits related to this system before performing the following procedure.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs using the GTS.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
A
B
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Sports Mode Selection SW | Sport mode select switch status | OFF or ON | ·
ON: Shift lever in M, "+" or "-" ·
OFF: Shift lever not in M, "+" or "-" |
- |
| Tester Display |
|---|
| Sports Mode Selection SW |
| Result | Proceed to |
|---|---|
| Data List value is normal | A |
| Data List value is not normal | B |
A
B
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Sports Shift Up SW | Sport shift up switch status | OFF or ON | ·
ON: Shift lever held in "+" ·
OFF: Shift lever not held in "+" |
- |
| Sports Shift Down SW | Sport shift down switch status | OFF or ON | ·
ON: Shift lever held in "-" ·
OFF: Shift lever not held in "-" |
- |
| Tester Display |
|---|
| Sports Shift Up SW |
| Sports Shift Down SW |
| Result | Proceed to |
|---|---|
| Data List value is normal | A |
| Data List value is not normal | B |
A
Click hereDrivetrain>K411 CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>CHECK FOR INTERMITTENT PROBLEMS
B
| *A | for LHD |
| *B | for RHD |
| *a | Component without harness connected
(Shift Lock Control Unit Assembly (Transmission Control Switch)) |
Disconnect the F133 shift lock control unit assembly (transmission control switch) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 3 (SFTU) - 2 (E) | Shift lever held in "+" | Below 1 Ω |
| Shift lever in M | 10 kΩ or higher | |
| 1 (SFTD) - 2 (E) | Shift lever held in "-" | Below 1 Ω |
| Shift lever in M | 10 kΩ or higher |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 1 (SFTU) - 2 (E) | Shift lever held in "+" | Below 1 Ω |
| Shift lever in M | 10 kΩ or higher | |
| 3 (SFTD) - 2 (E) | Shift lever held in "-" | Below 1 Ω |
| Shift lever in M | 10 kΩ or higher |
Connect the F133 shift lock control unit assembly (transmission control switch) connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the B48 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| B48-27 (SFTD) - Body ground | Shift lever held in "-" | Below 1 Ω |
| Shift lever in M | 10 kΩ or higher | |
| B48-17 (SFTU) - Body ground | Shift lever held in "+" | Below 1 Ω |
| Shift lever in M | 10 kΩ or higher |
Connect the B48 ECM connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>1NR-FE ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Component without harness connected
(Shift Lock Control Unit Assembly (Transmission Control Switch)) |
Disconnect the F133 shift lock control unit assembly (transmission control switch) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 4 (IG) - 5 (S) | Shift lever in M | Below 1 Ω |
| Shift lever not in M | 10 kΩ or higher |
Connect the F133 shift lock control unit assembly (transmission control switch) connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Shift Lock Control Unit Assembly (Transmission Control Switch)) |
Disconnect the F133 shift lock control unit assembly (transmission control switch) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F133-4 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the B48 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F133-5 (S) - B48-30 (S) | Always | Below 1 Ω |
| F133-5 (S) - Body ground and other terminals | Always | 10 kΩ or higher |
| B48-30 (S) - Body ground and other terminals | Always | 10 kΩ or higher |
Connect the B48 ECM connector.
Connect the F133 shift lock control unit assembly (transmission control switch) connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>1NR-FE ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT