The speed sensor detects wheel speed and sends the appropriate signals to the skid control ECU (brake actuator assembly). These signals are used for brake control.
Speed sensor rotors have rows of alternating N and S magnetic poles, and their magnetic fields change when the rotors turn.
Each speed sensor detects that magnetic change and sends a pulse signal to the skid control ECU (brake actuator assembly).
When the connectors between the speed sensor and skid control ECU (brake actuator assembly) are connected, the following waveform is output.
| *1 | Speed Sensor | *2 | Speed Sensor Rotor |
| *a | Waveform (Reference):
Between Speed Sensor (-) and Body Ground |
*b | Low speed |
| *c | High speed | - | - |
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1271 | Low Output Signal of Front Speed Sensor RH (Test Mode DTC) | Detected only during Test Mode. | Front speed sensor and speed sensor rotor RH (Front axle hub sub-assembly RH) |
| C1272 | Low Output Signal of Front Speed Sensor LH (Test Mode DTC) | Detected only during Test Mode. | Front speed sensor and speed sensor rotor LH (Front axle hub sub-assembly LH) |
| C1401 | Front Speed Sensor RH Malfunction | Any of the following is detected:
1.
At a vehicle speed of 10 km/h (6 mph) or more, output voltage from one of the speed sensors is less than that from the other sensors for 15 seconds or more. 2.
At a vehicle speed less than 10 km/h (6 mph), output from one of the speed sensors is 0 km/h (0 mph) for 1 second or more. 3.
At a vehicle speed of 10 km/h (6 mph) or more, outputs from both front speed sensors are 0 km/h (0 mph) for 15 seconds or more. (except when both rear speed sensors are 0 km/h (0 mph)) |
Front speed sensor and speed sensor rotor RH (Front axle hub sub-assembly RH) |
| C1402 | Front Speed Sensor LH Malfunction | Any of the following is detected:
1.
At a vehicle speed of 10 km/h (6 mph) or more, output voltage from one of the speed sensors is less than that from the other sensors for 15 seconds or more. 2.
At a vehicle speed less than 10 km/h (6 mph), output from one of the speed sensors is 0 km/h (0 mph) for 1 second or more. 3.
At a vehicle speed of 10 km/h (6 mph) or more, outputs from both front speed sensors are 0 km/h (0 mph) for 15 seconds or more. (except when both rear speed sensors are 0 km/h (0 mph)) |
Front speed sensor and speed sensor rotor LH (Front axle hub sub-assembly LH) |
Connect the GTS to the DLC3.
Start the engine.
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| FR Wheel Speed | Front wheel speed sensor RH reading | Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202 mph) |
Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| FL Wheel Speed | Front wheel speed sensor LH reading | Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202 mph) |
Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| Tester Display |
|---|
| FR Wheel Speed |
| FL Wheel Speed |
Check that there is no difference between the speed value output from the speed sensor displayed on the GTS and the speed value displayed on the speedometer when driving the vehicle.
Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION
The speed value output from the speed sensor displayed on the GTS is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).
The front speed sensor rotor is incorporated into the front axle hub sub-assembly. If the front speed sensor rotor needs to be replaced, replace it together with the front axle hub sub-assembly with front speed sensor.
If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.
If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG