| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1427 | Motor Malfunction | Actuator pump motor does not operate properly. | ·
Brake actuator assembly (Ground circuit) ·
Brake actuator assembly (Motor circuit) ·
Wire harness or connector |
Refer to DTCs C1361, C146C and C146D.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1361
When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.
According to the display on the GTS, perform the Active Test.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Motor Relay | Motor relay | Relay ON / OFF | Operating sound of motor can be heard. |
| Tester Display |
|---|
| Motor Relay |
Check the operating sound of the motor relay when operating it with the GTS.
| Result | Proceed to |
|---|---|
| The operating sound is not heard | A |
| The operating sound is heard | B |
A
B
Turn the ignition switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
Disconnect the skid control ECU (brake actuator assembly) connector.
| *A | for Manual Transaxle |
| *B | for Continuously Variable Transaxle |
| *a | Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A48-13 (GND2) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A49-13 (GND2) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
This code is detected when a problem is identified in the brake actuator assembly.
The motor relay is in the brake actuator assembly.
Therefore, motor relay unit inspection cannot be performed. Be sure to check if the DTC is output before replacing the brake actuator assembly.
Reconnect the A48*1 or A49*2 skid control ECU (brake actuator assembly) connector.
*1: for Manual Transaxle
*2: for Continuously Variable Transaxle
Clear the DTCs.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 20 km/h (12 mph) or more for 30 seconds or more.
Check if the same DTC is recorded.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
If a speed signal of 6 km/h (4 mph) or more is input to the skid control ECU (brake actuator assembly) with the ignition switch to ON and the stop light switch off, the ECU performs self diagnosis of the motor and solenoid circuits.
If the normal system code is output (no trouble codes are output), slightly jiggle the connectors, wire harness, and fuses of the brake actuator assembly. Make sure that no DTCs are output.
If any DTCs are output while jiggling a connector or wire harness of the skid control ECU (brake actuator assembly), inspect and repair the connector or wire harness.
The DTCs were probably output due to a bad connection of the connector terminal.
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC is output | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B