Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2016.04–2017.10
RM30M0E _54 Brake _017098 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0256246 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  ABS Warning Light Remains ON  


DESCRIPTION

The skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication.

If any of the following is detected, the ABS warning light remains on:

·

The skid control ECU (brake actuator assembly) connectors are disconnected from the skid control ECU (brake actuator assembly).

·

There is a malfunction in the skid control ECU (brake actuator assembly) internal circuit.

·

There is an open in the harness between the combination meter assembly and the skid control ECU (brake actuator assembly).

·

The ABS control system is defective.


HINT:

In some cases, the GTS cannot be used when the skid control ECU (brake actuator assembly) is abnormal.


WIRING DIAGRAM

C349116E01
0.156,2.281 4.135,2.479 3.979,0.198 10 false Combination Meter Assembly 2.417,1.833 6.396,2.031 3.979,0.198 10 false from IG Circuit 3.917,1.99 4.938,2.25 1.021,0.26 10 false IG1 NO. 2 4.927,0.969 5.948,1.229 1.021,0.26 10 false A48 5.25,0.969 6.271,1.229 1.021,0.26 10 false A49 4.927,1.854 5.948,2.115 1.021,0.26 10 false A48 5.25,1.854 6.271,2.115 1.021,0.26 10 false A49 5,0.792 6.021,1.052 1.021,0.26 10 false 1 5.323,0.792 6.344,1.052 1.021,0.26 10 false 1 5.292,1.156 6.313,1.417 1.021,0.26 10 false *2 4.969,1.156 5.99,1.417 1.021,0.26 10 false *1 4.969,1.677 5.99,1.938 1.021,0.26 10 false 34 4.969,2.042 5.99,2.302 1.021,0.26 10 false *1 5.292,1.677 6.313,1.938 1.021,0.26 10 false 34 5.292,2.042 6.313,2.302 1.021,0.26 10 false *2 5.479,2.292 7.052,2.75 1.573,0.458 10 false Skid Control ECU (Brake Actuator Assembly) 5.604,0.969 7.156,1.24 1.552,0.271 10 false GND1 5.604,1.854 7.156,2.125 1.552,0.271 10 false IG1 2.844,2.917 5.5,3.25 2.656,0.333 10 false *1: for Manual Transaxle 0.708,3.427 4.688,3.625 3.979,0.198 10 false : CAN Communication Line 2.833,3.25 5.49,3.583 2.656,0.333 10 false *2: for Continuously Variable Transaxle

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
DTC is not output A
DTC is output B



A

2.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED

B

2.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU (brake actuator assembly) connector is securely connected.

OK:

The connector is securely connected.



Result:
Proceed to
OK
NG



OK

3.CHECK BATTERY

NG

CONNECT CONNECTOR TO BRAKE ACTUATOR ASSEMBLY CORRECTLY

3.CHECK BATTERY
a.

Check the battery voltage.

Standard voltage:

11 to 14 V


Result:
Proceed to
OK
NG




OK

4.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)

NG

4.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)
a.
C349101C01
1.448,2.417 1.948,2.667 0.5,0.25 1.448,0.396 1.948,0.646 0.5,0.25 2.5,2.167 2.104,1.615 true 2.5,4.188 2.104,3.635 true 0.333,0.25 0.813,0.573 0.479,0.323 12 false *A 0.333,2.333 0.896,2.573 0.563,0.24 12 false *B 0.094,0.073 0.406,0.229 0.313,0.156 10 false *a 1.583,0.427 1.979,0.667 0.396,0.24 10 false A48 1.583,2.448 1.979,2.688 0.396,0.24 10 false A49 2.438,2.188 2.833,2.427 0.396,0.24 10 false IG1 2.438,4.208 2.833,4.448 0.396,0.24 10 false IG1
*A for Manual Transaxle
*B for Continuously Variable Transaxle
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Disconnect the skid control ECU (brake actuator assembly) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for Manual Transaxle
Tester Connection Switch Condition Specified Condition
A48-34 (IG1) - Body ground Ignition switch ON 11 to 14 V

for Continuously Variable Transaxle
Tester Connection Switch Condition Specified Condition
A49-34 (IG1) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)

5.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)
a.

Turn the ignition switch off.


b.
C349101C02
1.448,2.417 1.948,2.667 0.5,0.25 1.448,0.396 1.948,0.646 0.5,0.25 0.5,1.875 1.042,1.333 true 0.5,3.875 1.042,3.333 true 0.333,0.25 0.813,0.573 0.479,0.323 12 false *A 0.333,2.333 0.896,2.573 0.563,0.24 12 false *B 0.094,0.073 0.406,0.229 0.313,0.156 10 false *a 1.583,0.427 1.979,0.667 0.396,0.24 10 false A48 1.583,2.448 1.979,2.688 0.396,0.24 10 false A49 0.083,1.792 0.479,2.031 0.396,0.24 10 false GND1 0.083,3.792 0.479,4.031 0.396,0.24 10 false GND1
*A for Manual Transaxle
*B for Continuously Variable Transaxle
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for Manual Transaxle
Tester Connection Condition Specified Condition
A48-1 (GND1) - Body ground Always Below 1 Ω

for Continuously Variable Transaxle
Tester Connection Condition Specified Condition
A49-1 (GND1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.READ VALUE USING GTS (ABS WARNING LIGHT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)

6.READ VALUE USING GTS (ABS WARNING LIGHT)
a.

Reconnect the A48*1 or A49*2 skid control ECU (brake actuator assembly) connector.

*1: for Manual Transaxle

*2: for Continuously Variable Transaxle



b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


f.

According to the display on the GTS, read the Data List.


Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ABS Warning Light ABS warning light OFF or ON OFF: Warning light off
ON: Warning light on
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
ABS Warning Light
50003 105 51
g.

Check the GTS display condition of the ABS warning light.

Result:
Result Proceed to
Display of the Data List remains OFF A
Display of the Data List remains ON B




A

B