The skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication.
The slip indicator light blinks during VSC and/or TRC operation.
If a malfunction is detected, the slip indicator light comes on to warn the driver.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DIAGNOSIS SYSTEM
When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Check if CAN communication system DTCs are output.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC is output | B |
A
B
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Check if the skid control ECU (brake actuator assembly) connector is securely connected.
The connector is securely connected.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the battery voltage.
11 to 14 V
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *A | for Manual Transaxle |
| *B | for Continuously Variable Transaxle |
| *a | Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly)) |
Disconnect the skid control ECU (brake actuator assembly) connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A48-34 (IG1) - Body ground | Ignition switch ON | 10.5 to 16 V |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A49-34 (IG1) - Body ground | Ignition switch ON | 10.5 to 16 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
| *A | for Manual Transaxle |
| *B | for Continuously Variable Transaxle |
| *a | Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A48-1 (GND1) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A49-1 (GND1) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the A48*1 or A49*2 skid control ECU (brake actuator assembly) connector.
*1: for Manual Transaxle
*2: for Continuously Variable Transaxle
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Slip Indicator Light | SLIP indicator light | OFF or ON | OFF: Indicator light off
ON: Indicator light on |
- |
| Tester Display |
|---|
| Slip Indicator Light |
Check the GTS display condition of the slip indicator light.
| Result | Proceed to |
|---|---|
| Display of the Data List remains OFF | A |
| Display of the Data List remains ON | B |
A
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
B