Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2016.04–2018.01
RM30M0E _54 Brake _017098 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0256246 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  TS and CG Terminal Circuit  


DESCRIPTION

In Test Mode (signal check), a malfunction in the speed sensor that cannot be detected when the vehicle is stopped can be detected while driving.

Sensor check mode can be entered by connecting terminals TS and CG of the DLC3 and turning the ignition switch from off to ON.

WIRING DIAGRAM

C349108E01
1.146,1.729 1.458,1.927 0.313,0.198 10 false CG 1.167,0.656 1.479,0.854 0.313,0.198 10 false TS 0.708,2.365 1.188,2.583 0.479,0.219 10 false DLC3 0.708,2.198 1.188,2.417 0.479,0.219 10 false F16 1.5,1.625 1.813,1.823 0.313,0.198 10 false 4 1.5,0.552 1.813,0.75 0.313,0.198 10 false 12 5.125,0.656 5.438,0.854 0.313,0.198 10 false A48 5.448,0.656 5.76,0.854 0.313,0.198 10 false A49 5.188,0.479 5.5,0.677 0.313,0.198 10 false 33 5.51,0.479 5.823,0.677 0.313,0.198 10 false 33 5.51,0.854 5.823,1.052 0.313,0.198 10 false *2 5.188,0.854 5.5,1.052 0.313,0.198 10 false *1 5.813,0.656 6.125,0.854 0.313,0.198 10 false TS 1.417,2.75 4.042,3.042 2.625,0.292 10 false *1: for Manual Transaxle 1.417,3.083 4.042,3.375 2.625,0.292 10 false *2: for Continuously Variable Transaxle 5.479,2.208 7.073,2.615 1.594,0.406 10 false Skid Control ECU (Brake Actuator Assembly)

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (TS of DLC3 - SKID CONTROL ECU)
a.

Turn the ignition switch off.


b.

Disconnect the H6 skid control ECU (brake actuator assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for Manual Transaxle
Tester Connection Condition Specified Condition
A48-33 (TS) - F16-12 (TS) Always Below 1 Ω
A48-33 (TS) or F16-12 (TS) - Body ground Always 10 kΩ or higher

for Continuously Variable Transaxle
Tester Connection Condition Specified Condition
A49-33 (TS) - F16-12 (TS) Always Below 1 Ω
A49-33 (TS) or F16-12 (TS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)
a.
C269109C76
1.469,0.167 1.969,0.427 0.5,0.26 2.583,0.333 1.667,0.833 true 2.656,0.24 3,0.479 0.344,0.24 10 false CG 0.167,0.167 0.479,0.323 0.313,0.156 10 false *a 1.583,0.219 1.896,0.417 0.313,0.198 10 false F16
*a Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F16-4 (CG) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR