Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM › 2016.04–2017.10
RM30M0E _51 Engine / Hybrid System _052909 CRUISE CONTROL _0256264 CRUISE CONTROL SYSTEM C

CRUISE CONTROL  CRUISE CONTROL SYSTEM  P0571  Brake Switch "A" Circuit  


DESCRIPTION

When the brake pedal is depressed, the stop light switch assembly sends a signal to the ECM. When the ECM receives this signal, it cancels cruise control system control of vehicle speed. The fail-safe function operates to enable normal driving even if there is a malfunction in the stop light signal circuit. The cancellation condition occurs when voltage is applied to terminal STP. When the brake is applied, voltage is normally applied to terminal STP of the ECM through the STOP fuse and the stop light switch assembly, and the ECM cancels control of vehicle speed by the cruise control system.

DTC No. Detection Item DTC Detection Condition Trouble Area
P0571 Brake Switch "A" Circuit When voltage of STP terminal and that of ST1- terminal of ECM are less than 1 V for 0.5 sec. or more
·

Stop light switch assembly

·

Stop light switch circuit

·

ECM

·

Harness or connector



WIRING DIAGRAM

C353743E02
0.5,0.75 1.5,1.083 1,0.333 10 false from IG2 NO.1 Fuse 0.333,1.583 1.5,1.833 1.167,0.25 10 false from STOP Fuse 2.75,0.583 2.917,0.75 0.167,0.167 10 false 4 2.75,1.417 2.917,1.583 0.167,0.167 10 false 2 4.083,0.583 4.25,0.75 0.167,0.167 10 false 3 4.083,1.417 4.25,1.583 0.167,0.167 10 false 1 3,1.417 3.167,1.583 0.167,0.167 10 false B 3,0.583 3.167,0.75 0.167,0.167 10 false B 3.833,0.583 4,0.75 0.167,0.167 10 false L 3.833,1.417 4,1.583 0.167,0.167 10 false L 2.917,2 3.25,2.167 0.333,0.167 10 false A21 2.917,2.167 4.75,2.417 1.833,0.25 10 false Stop Light Switch Assembly 5.354,1.354 5.604,1.521 0.25,0.167 10 false 10 5.292,1.563 5.625,1.729 0.333,0.167 10 false F131 5.354,0.563 5.604,0.729 0.25,0.167 10 false 11 5.292,0.76 5.625,0.927 0.333,0.167 10 false F131 5.698,0.75 6.031,0.917 0.333,0.167 10 false ST1- 5.698,1.552 6.031,1.719 0.333,0.167 10 false STP 6,2 6.333,2.167 0.333,0.167 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
a.
E144327C12
0.396,1.958 0.833,2.302 0.438,0.344 1.865,2.063 2.396,1.354 true 1.906,2.552 2.323,2.896 true 0.5,2.031 1.104,2.448 0.604,0.417 10 false A21 0.24,0.177 0.656,0.573 0.417,0.396 10 false *a 2.448,1.229 2.667,1.438 0.219,0.208 10 false B 2.375,2.813 2.594,3.021 0.219,0.208 10 false B
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Disconnect the stop light switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A21-2 (B) - Body ground Always 11 to 14 V
A21-4 (B) - Body ground Ignition switch ON 11 to 14 V



c.

Reconnect the stop light switch assembly connector.


Result:
Proceed to
OK
NG



OK

2.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Remove the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL


b.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (ECM - STOP LIGHT SWITCH ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (ECM - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the F131 ECM connector.


b.

Disconnect the A21 stop light switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
F131-10 (STP) - A21-1 (L) Always Below 1 Ω
F131-11 (ST1-) - A21-3 (L) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
F131-10 (STP) or A21-1 (L) - Body ground Always 10 kΩ or higher
F131-11 (ST1-) or A21-3 (L) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



d.

Reconnect the stop light switch assembly connector.


e.

Reconnect the ECM connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR