Home › Steering › STEERING COLUMN › STEERING LOCK SYSTEM › 2016.04–2016.10
RM30M0E _55 Steering _017104 STEERING COLUMN _0090111 STEERING LOCK SYSTEM J

STEERING COLUMN  STEERING LOCK SYSTEM  Unable to Lock Steering Wheel  


DESCRIPTION

The steering lock actuator activates the steering lock motor and moves the lock bar into the steering column to lock the steering.

When the steering lock is operating, the steering may not lock when the lock bar is not aligned with the lock hole of the steering column. In this case, the steering can be locked by turning the steering wheel a little in the same manner as is done for a vehicle with a mechanical key to change the position of the lock hole.

Related Data List and Active Test Items
Problem Symptom Data List Item Active Test Item
Unable to lock steering wheel
Entry&Start
·

All items

Click here(Click here)


-

WIRING DIAGRAM

C301973E01
0.708,2.344 1.021,2.542 0.313,0.198 10 false 2N 0.75,2.177 0.906,2.375 0.156,0.198 10 false 1 1.458,2.344 1.771,2.542 0.313,0.198 10 false MB 1.479,2.177 1.792,2.375 0.313,0.198 10 false 18 0.719,3.198 1.698,3.938 0.979,0.74 10 false Driver Side Junction Block Assembly 1.802,2.344 2.417,2.542 0.615,0.198 10 false DCTY 2.938,1.74 3.396,1.938 0.458,0.198 10 false F52 2.979,1.563 3.292,1.76 0.313,0.198 10 false 16 2.531,1.74 2.99,1.938 0.458,0.198 10 false RDA 2.542,2.583 3,2.781 0.458,0.198 10 false PRG 2.938,2.583 3.396,2.781 0.458,0.198 10 false F52 3.031,2.406 3.188,2.604 0.156,0.198 10 false 9 3.521,1.563 3.833,1.76 0.313,0.198 10 false 13 3.49,1.74 3.948,1.938 0.458,0.198 10 false F44 3.521,2.406 3.833,2.604 0.313,0.198 10 false 36 3.49,2.583 3.948,2.781 0.458,0.198 10 false F44 3.833,1.74 4.448,1.938 0.615,0.198 10 false RDA3 3.833,2.583 4.448,2.781 0.615,0.198 10 false PRG3 4.344,1.49 4.802,1.688 0.458,0.198 10 false LIN 4.74,1.313 4.896,1.51 0.156,0.198 10 false 5 4.656,1.49 5.115,1.688 0.458,0.198 10 false F43 4.688,1.865 5,2.063 0.313,0.198 10 false 17 4.656,2.031 5.115,2.229 0.458,0.198 10 false F43 4.188,2.042 4.802,2.24 0.615,0.198 10 false SLR+ 5.167,1.323 5.323,1.521 0.156,0.198 10 false 5 5.167,1.927 5.323,2.125 0.156,0.198 10 false 3 5.167,2.458 5.323,2.656 0.156,0.198 10 false 1 5.365,1.49 5.823,1.688 0.458,0.198 10 false LIN 5.375,2.031 5.833,2.229 0.458,0.198 10 false IGE 5.375,2.552 5.833,2.75 0.458,0.198 10 false GND 1.844,3.198 3.833,3.396 1.99,0.198 10 false Body Computer 3.667,3.188 4.781,5.115 1.115,1.927 10 false Certification ECU (Smart Key ECU Assembly) 5.167,3.969 5.625,4.167 0.458,0.198 10 false F15 5.167,4.135 6.948,5.781 1.781,1.646 10 false Steering Lock ECU (Steering Lock Actuator Assembly) 1.719,4.198 1.875,4.396 0.156,0.198 10 false 1 1.385,4.469 2.26,4.75 0.875,0.281 10 false F31 1.385,4.635 3.042,5.76 1.656,1.125 10 false Front Door Courtesy Light Switch Assembly LH 5.167,0.979 5.49,1.177 0.323,0.198 10 false 7 1.385,5.729 1.844,5.927 0.458,0.198 10 false F32 1.719,5.458 1.875,5.656 0.156,0.198 10 false 1 1.385,5.896 3.042,6.521 1.656,0.625 10 false Front Door Courtesy Light Switch Assembly RH 0.635,6.469 4.302,6.667 3.667,0.198 10 false : LIN Communication Line 4.396,5.667 6.083,5.865 1.688,0.198 10 false *1: for LHD 4.396,6.052 6.083,6.25 1.688,0.198 10 false *2: for RHD 0.969,4.198 1.281,4.396 0.313,0.198 10 false *1 0.99,5.458 1.302,5.656 0.313,0.198 10 false *2 1.594,0.208 1.75,0.406 0.156,0.198 10 false 7 1.792,0.302 1.948,0.5 0.156,0.198 10 false E 2.646,0.302 2.958,0.5 0.313,0.198 10 false P2 2.948,0.208 3.104,0.406 0.156,0.198 10 false 2 3.563,0.135 3.719,0.333 0.156,0.198 10 false 8 3.49,0.302 3.948,0.5 0.458,0.198 10 false F43 3.833,0.302 3.99,0.5 0.156,0.198 10 false P 6.125,0.25 6.979,0.479 0.854,0.229 10 false from Battery 1.448,0.594 1.906,0.792 0.458,0.198 10 false F20 1.448,0.76 3.583,1.115 2.135,0.354 10 false Shift Lock Control ECU (Shift Lock Control Unit Assembly)*3 5.375,1.063 5.531,1.26 0.156,0.198 10 false B 4.406,6.427 6.833,6.667 2.427,0.24 10 false *3: for Automatic Transaxle and CVT 5.021,0.417 5.896,0.646 0.875,0.229 10 false STRG LOCK

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry & Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Perform either of the following operations to lock/unlock the steering:

·

To unlock the steering, carry the key and turn the engine switch on (ACC) or on (IG) with the shift lever in P*.

·

To lock the steering, turn the engine switch off with the shift lever in P*, and then open a door.

*: for Automatic Transaxle and CVT



·

Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart.

Click hereSteering>STEERING COLUMN>STEERING LOCK SYSTEM>DIAGNOSTIC TROUBLE CODE CHART

·

The steering lock system uses LIN communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

When replacing the steering lock ECU (steering lock actuator assembly) or certification ECU (smart key ECU assembly), registration must be performed (refer to Service Bulletin).

·

After performing repairs, confirm that the problem does not recur.

·

When disconnecting the cable from the negative (-) battery terminal, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.READ VALUE USING GTS (LOCK REQUEST RECEIVE)
a.

Turn the engine switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / Entry&Start / Data List.


f.

According to the display on the GTS, read the Data List.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Lock Request Receive Reception state of steering lock request signal by certification ECU (smart key ECU assembly)
HINT:
·

The reception state is maintained for 10 seconds.

·

When 10 seconds or more have elapsed after receiving the signal, the item changes to "NG".



OK or NG OK: Within 10 seconds of opening any door with engine switch off and shift lever in P*
NG: Except above
If this item does not change to "OK" even though the steering lock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning.

*: for Automatic Transaxle and CVT


Body Electrical > Entry&Start > Data List
Tester Display
Lock Request Receive
50003 125 68
OK:

The certification ECU (smart key ECU assembly) receives a lock request signal within 10 seconds of turning the engine switch from on (IG) to off and opening a door with the shift lever in P (for Automatic Transaxle and CVT), and OK is displayed on the GTS screen.



Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

2.READ VALUE USING GTS (L CODE CHECK)

B

9.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY LH

C

11.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY RH
2.READ VALUE USING GTS (L CODE CHECK)
a.

Turn the engine switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / Entry&Start / Data List.


f.

According to the display on the GTS, read the Data List.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
L Code Check Verification result between certification ECU (smart key ECU assembly) and steering lock ECU (steering lock actuator assembly) OK or NG OK: Verification result normal
NG: Verification result abnormal
When a malfunction is present:
·

The ID code for the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator assembly) is not registered or the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator) is malfunctioning.

·

The steering cannot be locked.

·

The steering cannot be unlocked (the engine cannot be started).


Body Electrical > Entry&Start > Data List
Tester Display
L Code Check
50003 125 66
OK:

OK is displayed on the GTS.


HINT:
Reasons for verification failure:
·

The steering lock ECU (steering lock actuator assembly) or certification ECU (smart key ECU assembly) is malfunctioning.

·

There is a problem with the communication between ECUs.

·

An ECU is replaced, but is not registered.

·

An ECU is replaced with an ECU which has a code already stored in it.




Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

NG

7.REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
a.

Disconnect the steering lock ECU (steering lock actuator assembly) connector.


b.
C157850C61
0.344,0.896 0.833,1.188 0.49,0.292 1.302,2.417 1.052,1.677 true 2.25,2.417 2.5,1.677 true 0.396,0.302 0.625,0.479 0.229,0.177 10 false *a 0.49,0.969 0.979,1.24 0.49,0.271 10 false F15 0.708,1.573 1.063,1.76 0.354,0.188 10 false GND 2.563,1.573 2.719,1.76 0.156,0.188 10 false B
*a Front view of wire harness connector
(to Steering Lock ECU (Steering Lock Actuator Assembly))


Measure the resistance and voltage according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F15-1 (GND) - Body ground Always Below 1 Ω


NOTICE:

If the result is not as specified, check for looseness in the ground cable connection.


Standard Voltage:
Tester Connection Condition Specified Condition
F15-7 (B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.INSPECT STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY) (MOTOR ACTIVATION COMMAND SIGNAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY) (MOTOR ACTIVATION COMMAND SIGNAL)
a.
C157850C62
0.344,0.917 0.74,1.229 0.396,0.313 1.281,2.417 1.031,1.729 true 0.375,0.302 0.823,0.604 0.448,0.302 10 false *a 0.438,0.99 0.854,1.354 0.417,0.365 10 false F15 0.698,1.625 1.052,1.813 0.354,0.188 10 false GND
*a Front view of wire harness connector
(to Steering Lock ECU (Steering Lock Actuator Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F15-1 (GND) - Body ground Always Below 1 Ω



b.

Reconnect the steering lock ECU (steering lock actuator assembly) connector.


c.

Move the shift lever to P* and turn the engine switch off.

*: for Automatic Transaxle and CVT



d.
C241547C43
0.25,0.667 0.594,0.948 0.344,0.281 0.354,2.896 1.729,3.063 1.375,0.167 2.313,2.958 2.719,3.073 0.406,0.115 1.563,4.031 2.521,4.198 0.958,0.167 2.302,1.104 2.823,1.917 true 1.573,2.896 2.896,2.625 2.896,2.625 2.635,2.958 true 2.115,4.198 2.115,4.458 true 1.854,1.104 1.083,1.917 true 0.385,0.115 0.708,0.344 0.323,0.229 10 false *a 2.927,2.521 3.104,2.708 0.177,0.188 10 false *b 2.042,4.469 2.344,4.667 0.302,0.198 10 false *c 0.313,0.729 0.625,0.896 0.313,0.167 10 false F15 0.938,1.948 1.458,2.208 0.521,0.26 10 false IGE 2.708,1.958 3.063,2.125 0.354,0.167 10 false GND 3.052,4.01 3.427,4.177 0.375,0.167 10 false GND
*a Component with harness connected
(Steering Lock ECU (Steering Lock Actuator Assembly))
*b Steering lock motor not operating
*c Steering lock motor operating


Check the signal waveform according to the condition(s) in the table below.

Standard Frequency:
Item Content
Tester Connection F15-3 (IGE) - F15-1 (GND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Vehicle Condition Steering lock motor not operating → Operating → Not operating


HINT:
·

When taking measurements when the lock motor is stopped, it is not necessary to perform any operations.

·

In order to take measurements when the lock motor is operating, perform either of the following operations:

·

To unlock the steering, carry the key and turn the engine switch on (ACC) or on (IG) with the shift lever in P*.


·

To lock the steering, turn the engine switch off with the shift lever in P*, and then open a door.


*: for Automatic Transaxle and CVT





Result:
Proceed to
OK
NG



OK

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)

NG

5.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
5.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the F15 steering lock ECU (steering lock actuator assembly) connector.


b.

Disconnect the F43 certification ECU (smart key ECU assembly) connector.


c.

Check for deformation and corrosion of the connector case and terminals.

OK:

There is no deformation or corrosion of the connector case or terminals.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F15-3 (IGE) - F43-17 (SLR+) Always Below 1 Ω
F15-3 (IGE) - Body ground Always 10 kΩ or higher
F43-17 (SLR+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)
a.

Reconnect the steering lock ECU (steering lock actuator assembly) connector.


b.
C157849C29
0.292,0.885 0.74,1.177 0.448,0.292 1.854,1.958 2.688,2.677 true 0.375,0.271 0.667,0.521 0.292,0.25 10 false *a 0.417,0.948 0.792,1.198 0.375,0.25 10 false F15 2.729,2.688 3.177,2.896 0.448,0.208 10 false IGE
*a Component with harness connected
(Steering Lock ECU (Steering Lock Actuator Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F15-3 (IGE) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)

7.REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)
a.

Replace the steering lock ECU (steering lock actuator assembly) with a new one.

Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY>DISASSEMBLY


b.

Perform registration.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

8.READ VALUE USING GTS (L CODE CHECK)
8.READ VALUE USING GTS (L CODE CHECK)
a.

Turn the engine switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / Entry&Start / Data List.


f.

According to the display on the GTS, read the Data List.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
L Code Check Verification result between certification ECU (smart key ECU assembly) and steering lock ECU (steering lock actuator assembly) OK or NG OK: Verification result normal
NG: Verification result abnormal
When a malfunction is present:
·

The ID code for the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator assembly) is not registered or the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator) is malfunctioning.

·

The steering cannot be locked.

·

The steering cannot be unlocked (the engine cannot be started).


Body Electrical > Entry&Start > Data List
Tester Display
L Code Check
50003 125 66
OK:

OK is displayed on the GTS.



Result:
Proceed to
OK
NG



OK

END (STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)) WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

9.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY LH
a.

Remove the front door courtesy light switch assembly LH.

Click hereVehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>REMOVAL


b.

Inspect the front door courtesy light switch assembly LH.

Click hereVehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>INSPECTION

OK:

Front door courtesy light switch assembly LH is normal.


Result:
Proceed to
OK
NG




OK

10.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY LH - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)

NG

REPLACE FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY LH

10.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY LH - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the F31 front door courtesy light switch assembly LH connector.


b.

Disconnect the 2N driver side junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F31-1 - 2N-1 Always Below 1 Ω
F31-1 - Body ground Always 10 kΩ or higher
2N-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

13.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY RH
a.

Remove the front door courtesy light switch assembly RH.

Click hereVehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>REMOVAL


b.

Inspect the front door courtesy light switch assembly RH.

Click hereVehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>INSPECTION

OK:

Front door courtesy light switch assembly RH is normal.



Result:
Proceed to
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY RH - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)

NG

REPLACE FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY RH

12.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY RH - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the F32 front door courtesy light switch assembly RH connector.


b.

Disconnect the 2N driver side junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
F32-1 - 2N-1 Always Below 1 Ω
F32-1 - Bodyground Always 10 kΩ or higher
2N-1 - Bodyground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



OK

13.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY
a.

Remove the driver side junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the body computer from the driver side junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

C280674C02
1.271,0.042 1.594,0.323 0.323,0.281 5.094,0.073 5.417,0.333 0.323,0.26 5.24,1.896 5.073,1.896 5.073,1.896 4.656,1.354 true 0.271,0.156 0.583,0.354 0.313,0.198 10 false *a 1.323,0.115 1.635,0.313 0.313,0.198 10 false 2N 5.167,0.135 5.479,0.333 0.313,0.198 10 false MB 5.354,1.823 5.813,2.021 0.458,0.198 10 false DCTY
*a Component without harness connected
(Driver Side Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
2N-1 - MB-18 (DCTY) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

14.REPLACE BODY COMPUTER

NG

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY

14.REPLACE BODY COMPUTER
a.

Replace the body computer with a new one.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

15.CHECK STEERING LOCK CONDITION
15.CHECK STEERING LOCK CONDITION
a.

The engine switch is off.


b.

The shift lever is in P*1.


c.

A door is opened or a door lock operation (door lock, wireless door lock or key-linked lock operation*2) is performed.

HINT:

*1: for Automatic Transaxle and CVT

*2: This is the lock/unlock operation with the mechanical key.



d.

Turn the steering wheel and check the steering condition.

OK:

Steering is locked.



Result:
Result Proceed to
OK A
NG (for Manual Transaxle) B
NG (for Automatic Transaxle and CVT) C



A

END (BODY COMPUTER WAS DEFECTIVE)

B

17.CHECK STEERING LOCK CONDITION

C

16.READ VALUE USING GTS (SHIFT P SIGNAL)
16.READ VALUE USING GTS (SHIFT P SIGNAL)
a.

Turn the engine switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / Power Source Control / Data List.


f.

According to the display on the GTS, read the Data List.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift P Signal Shift position (P) signal OK or NG ON: Shift lever in P
OFF: Shift lever not in P
·

Use this item to determine if the shift position switch is malfunctioning.

·

The engine cannot be started when this item is "OFF".


OK:

ON (shift lever in P) or OFF (shift lever not in P) appears on the screen according to the shift lever position.



Result:
Proceed to
OK
NG



OK

17.CHECK STEERING LOCK CONDITION

NG

21.INSPECT SHIFT LOCK CONTROL ECU (SHIFT LOCK CONTROL UNIT ASSEMBLY)
17.CHECK STEERING LOCK CONDITION
a.

The engine switch is off.


b.

The shift lever is in P*1.


c.

A door is opened or a door lock operation (door lock, wireless door lock or key-linked lock operation*2) is performed.

HINT:

*1: for Automatic Transaxle and CVT

*2: This is the lock/unlock operation with the mechanical key.



d.

Turn the steering wheel and check the steering condition.

OK:

Steering is locked.



Result:
Proceed to
OK
NG



OK

END (CONNECT CONNECTORS PROPERLY)

NG

18.READ VALUE USING GTS (STEERING LOCK, STEERING UNLOCK)
18.READ VALUE USING GTS (STEERING LOCK, STEERING UNLOCK)
a.

Turn the engine switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / Entry&Start / Data List.


f.

According to the display on the GTS, read the Data List.


Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Steering Lock State of whether steering lock ECU
(steering lock actuator assembly)
has determined steering is locked
Set or Unset Set: Steering locked
Unset: Steering unlocked
If this item displays "Unset", the steering does not lock.
Steering Unlock State of whether steering lock ECU
(steering lock actuator assembly)
determined steering is unlocked
Set or Unset Set: Steering unlocked
Unset: Steering locked
If this item displays "Unset", the steering does not unlock (engine cannot be started).
OK:

"Steering Lock" is "Set" and "Steering Unlock" is "Unset"


Result:
Proceed to
OK
NG



OK

19.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)

19.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) with a new one.

HINT:

Refer to Service Bulletin.



b.

Perform registration.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

20.READ VALUE USING GTS (LOCK REQUEST RECEIVE)
20.READ VALUE USING GTS (LOCK REQUEST RECEIVE)
a.

Turn the engine switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / Entry&Start / Data List.


f.

According to the display on the GTS, read the Data List.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Lock Request Receive Reception state of steering lock request signal by certification ECU (smart key ECU assembly)
HINT:
·

The reception state is maintained for 10 seconds.

·

When 10 seconds or more have elapsed after receiving the signal, the item changes to "NG".



OK or NG OK: Within 10 seconds of opening any door with engine switch off and shift lever in P*
NG: Except above
If this item does not change to "OK" even though the steering lock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning.

*: for Automatic Transaxle and CVT


Body Electrical > Entry&Start > Data List
Tester Display
Lock Request Receive
50003 125 68
OK:

The certification ECU (smart key ECU assembly) receives a lock request signal within 10 seconds of turning the engine switch from on (IG) to off and opening a door with the shift lever in P (for Automatic Transaxle and CVT), and OK is displayed on the GTS screen.



Result:
Proceed to
OK
NG



OK

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

NG

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)

21.INSPECT SHIFT LOCK CONTROL ECU (SHIFT LOCK CONTROL UNIT ASSEMBLY)
a.

Disconnect the F20 shift lock control ECU (shift lock control unit assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.


E292928C02
1.021,1.885 1.542,1.406 true 1.865,1.156 2.438,1.906 true 0.104,0.104 0.417,0.365 0.313,0.26 10 false *a 2.51,1.833 2.823,2.031 0.313,0.198 10 false P2 0.865,1.823 1.021,2.021 0.156,0.198 10 false E
*a Component without harness connected
(Shift Lock Control ECU (Shift Lock Control Unit Assembly))


Standard Resistance:
Tester Connection Condition Specified Condition
2 (P2) - 7 (E) Shift lever in P Below 1 Ω
Shift lever not in P 10 kΩ or higher


Result:
Proceed to
OK
NG



OK

22.CHECK HARNESS AND CONNECTOR (SHIFT LOCK CONTROL ECU (SHIFT LOCK CONTROL UNIT ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) AND BODY GROUND)

NG

REPLACE SHIFT LOCK CONTROL ECU SUB-ASSEMBLY

22.CHECK HARNESS AND CONNECTOR (SHIFT LOCK CONTROL ECU (SHIFT LOCK CONTROL UNIT ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) AND BODY GROUND)
a.

Disconnect the F20 shift lock control ECU (shift lock control unit assembly) connector.


b.

Disconnect the F43 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
F20-2 (P2) - F43-8 (P) Always Below 1 Ω
F20-7 (E) - Body ground Always Below 1 Ω
F20-2 (P2) - Body ground Always 10 kΩ or higher
F43-8 (P) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



OK

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR