Home › Drivetrain › K312 CVT › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › 2016.04–2017.10
RM30M0E _52 Drivetrain _052969 K312 CVT _0256556 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM U

K312 CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List.

HINT:
·

To display the list box, press the pull down menu button next to Primary. Then select a measurement group.

·

When selecting a measurement group, the ECM data belonging to that group is displayed.




g.

According to the display on the GTS, read the Data List.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle Speed Vehicle speed Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)
Actual vehicle speed
·

This is the current vehicle speed.

·

The vehicle speed is detected using the wheel speed sensors.

·

There is a delay in when the vehicle speed data is displayed. Therefore, even if the vehicle speed listed in the freeze frame data is 0 km/h (0 mph), this does not always mean that the malfunction occurred when the vehicle was stopped.



Engine Speed Engine speed Min.: 0 rpm
Max.: 16383.75 rpm
680 to 780 rpm: Idling with warm engine, shift lever in N, A/C off When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed.
MAF Airflow rate from mass air flow meter Min.: 0 gm/sec.
Max.: 655.35 gm/sec.
·

1.0 to 3.0 gm/sec: Idling with warm engine (A/C off and shift lever in N)

·

3.0 to 9.0 gm/sec: 3000 rpm (A/C off and shift lever in N)


This is the intake air amount from the mass air flow meter.
Coolant Temp Engine coolant temperature Min.: -40°C (-40°F)
Max.: 140°C (284°F)
75 to 100°C (167 to 212°F): After warming up This is the engine coolant temperature.
HINT:
·

After warming up the engine, the engine coolant temperature is 75 to 100°C (167 to 212°F).

·

After a long soak, the engine coolant temperature, intake air temperature and ambient air temperature are approximately equal.

·

If the value is -40°C (-40°F), or 140°C (284°F), the sensor circuit is open or shorted.

·

Check if the engine overheats when the value indicates 140°C (284°F).



Throttle Motor DUTY Throttle actuator Min.: 0%
Max.: 100%
10 to 22%: Idling (A/C off and shift lever in N) This is the output duty ratio of the throttle actuator drive circuit.
N Range Status Judgment for shift lever in N OFF or ON
·

OFF: Shift lever not in P or N

·

ON: Shift lever in P or N


-
Starter Signal Starter signal OFF or ON
·

ON: Starter operating

·

OFF: Starter not operating


-
Neutral Position SW Signal Park/neutral position switch status OFF or ON
·

OFF: Shift lever not in P or N

·

ON: Shift lever in P or N


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
HINT:

If the same malfunction occurs even after adjusting these parts, refer to DTC P0705*1.


Stop Light Switch Stop light switch OFF or ON
·

ON: Brake pedal depressed

·

OFF: Brake pedal released


-
A/C Signal A/C switch status OFF or ON ON: A/C switch on -
Closed Throttle Position SW Closed throttle position switch status OFF or ON
·

ON: Throttle fully closed

·

OFF: Throttle open


-
TC and TE1 TC and CG (TE1) terminals of DLC3 OFF or ON - -
SPD (NT) Input turbine speed (NT) Min.: 0 rpm
Max.: 12750 rpm
·

Input turbine speed (NT) equal to engine speed (NE): Lock-up ON (After warming up engine)

·

Input turbine speed (NT) nearly equal to engine speed (NE): Lock-up OFF (Idling with shift lever in P or N)

·

0 rpm: Vehicle stopped with shift lever in D


Data is displayed in increments of 50 rpm.
Shift SW Status (P Range) Park/neutral position switch status OFF or ON
·

OFF: Shift lever not in P

·

ON: Shift lever in P


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
HINT:

If the same malfunction occurs even after adjusting these parts, refer to DTC P0705*1.


Shift SW Status (R Range) Park/neutral position switch status OFF or ON
·

OFF: Shift lever not in R

·

ON: Shift lever in R


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
HINT:

If the same malfunction occurs even after adjusting these parts, refer to DTC P0705*1.


Shift SW Status (N Range) Park/neutral position switch status OFF or ON
·

OFF: Shift lever not in N

·

ON: Shift lever in N


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
HINT:

If the same malfunction occurs even after adjusting these parts, refer to DTC P0705*1.


Shift SW Status (N,P Range) Supported Shift lever position P or N support status Supp or Unsupp Supp: Normal -
Shift SW Status (N,P Range) Park/neutral position switch status OFF or ON
·

OFF: Shift lever not in P or N

·

ON: Shift lever in P or N


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
HINT:

If the same malfunction occurs even after adjusting these parts, refer to DTC P0705*1.


Sports Shift Up SW Sport shift up switch status OFF or ON
·

ON: Shift lever held in "+"

·

OFF: Shift lever not held in "+"


-
Sports Shift Down SW Sport shift down switch status OFF or ON
·

ON: Shift lever held in "-"

·

OFF: Shift lever not held in "-"


-
Sports Mode Selection SW Sport mode select switch status OFF or ON
·

ON: Shift lever in M, "+" or "-"

·

OFF: Shift lever not in M, "+" or "-"


-
Shift SW Status (D Range) Park/neutral position switch status OFF or ON
·

OFF: Shift lever not in D or M

·

ON: Shift lever in D or M


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
HINT:

If the same malfunction occurs even after adjusting these parts, refer to DTC P0705*1.


A/T Oil Temperature 1 CVT fluid temperature sensor value Min.: -40.0°C (-40°F)
Max.: 150.0°C (302°F)
·

Approximately 100°C (212°F): After stall speed test

·

Equal to ambient temperature after cold soak


If the value is -40°C (-40°F) or 150°C (302°F) or more, the CVT fluid temperature sensor circuit is open or shorted.
NT Sensor Voltage Transmission revolution sensor (NT) output voltage Min.: 0.000 V
Max.: 4.999 V
0.6 to 1.5 V: Engine idling (Vehicle stopped with shift lever in P or N) -
SPD (NIN) Primary pulley speed (NIN) Min.: 0 rpm
Max.: 12750 rpm
·

0 rpm: Vehicle stopped

·

Primary pulley speed (NIN) equal to engine speed (NE): Lock-up ON (After warming up engine)


Data is displayed in increments of 50 rpm.
SPD (NOUT) Secondary pulley speed (NOUT) Min.: 0 rpm
Max.: 12750 rpm
·

0 rpm: Vehicle stopped

·

Approximately 2622 rpm: Vehicle being driven at approximately 60 km/h (37 mph)


Data is displayed in increments of 50 rpm.
NOUT Sensor Voltage Transmission revolution sensor (NOUT) output voltage Min.: 0.000 V
Max.: 4.999 V
0.6 to 1.5 V: Engine idling (Vehicle stopped with shift lever in P or N) -
A/T Oil Pressure Secondary oil pressure value Min.: -64 MPa
Max.: 63.998 MPa
Secondary oil pressure inspection:
·

4.2 to 4.9 MPa(42.8 to 50.0 kgf/cm2, 609 to 711 psi): D position stall test

·

4.0 to 5.1 MPa(40.8 to 52.0 kgf/cm2, 580 to 740 psi): R position stall test


-
G Sensor Converted output voltage of yaw rate and acceleration sensor assembly Min.: 0 V
Max.: 79.998 V
·

2.31 to 2.69 V: Vehicle on level ground

·

1.88 to 2.5 V: Decelerating

·

2.5 to 3.11 V: Accelerating

·

Stuck at 1.87 V: G sensor malfunction

·

Stuck at 1.87 V: Communication malfunction


-
Lock Up Lock-up OFF or ON
·

ON: Lock-up operating

·

OFF: Lock-up not operating


-
Shift Status ECM gearshift command 1st, 2nd, 3rd, 4th or 5th Same as actual shift position *2
Solenoid (SLS) Shift solenoid valve SLS status OFF or ON
·

ON: After engine start

·

OFF: Ignition switch ON


-
SLU Solenoid Status Shift solenoid valve SLU status OFF or ON
·

ON: Lock-up operating

·

OFF: Lock-up not operating


-
SL Solenoid Status Shift solenoid valve SL status OFF or ON
·

ON: Lock-up permitted

·

OFF: Lock-up not permitted


-
Solenoid(SC) Shift solenoid valve SC status OFF or ON
·

ON: For 1 second after moving shift lever from P to D or R, or N to D or R

·

ON: Lock-up ON to OFF

·

OFF: Engine idling


-
Solenoid(SLP) Shift solenoid valve SLP status OFF or ON
·

ON: After engine start

·

OFF: Ignition switch ON


-
G Sensor Calibration Deceleration Sensor Zero Point Calibration status Incomplete or Complete Complete -
G Sensor Learning Value Yaw rate and acceleration sensor assembly learned value voltage Min.: 0 V
Max.: 79.998 V
2.31 to 2.69 V: Deceleration Sensor Zero Point Calibration complete -
CVT Oil Press Calibration CVT Oil Pressure Calibration status Incompl or Compl Compl -
HINT:
·

*2: "Shift Status" is a signal divided into 5 gear positions for Active Test.

It does not express gear ratios for normal driving or gear positions for 7-speed sport sequential shiftmatic mode.





ACTIVE TEST


HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Active Test.


g.

According to the display on the GTS, perform the Active Test.

Powertrain > Engine and ECT > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Connect the TC and TE1 Connects and disconnects terminals TC and TE1 ON or OFF
·

ON: TC and TE1 are connected.

·

OFF: TC and TE1 are disconnected.


(Vehicle Condition)
Perform with the ignition switch ON, the engine stopped and the shift lever in P.
Activate the Solenoid (SLU) Operates shift solenoid valve SLU ON or OFF (Vehicle Condition)
Perform with the ignition switch ON, the engine stopped and the shift lever in P or N.
Activate the Lock Up Operates the Lock-up ON or OFF Possible to check lock-up operation.
Perform "Activate the Lock Up" while monitoring the Engine Speed and SPD (NT).
(Vehicle Condition)
Perform at a vehicle of speed 60 km/h (37 mph) or more.
Activate the Solenoid (SL) Operates shift solenoid valve SL ON or OFF (Vehicle Condition)
Perform with the ignition switch ON, the engine stopped and the shift lever in P or N.
Control the Shift Position Operates the shift solenoid valves to allow the gear position to be manually selected (1st - 2nd - 3rd - 4th - 5th)
Reference gear ratios:
1st (2.48 gear ratio max.) - 2nd(1.46) - 3rd (1.01) - 4th (0.70) - 5th (0.40 gear ratio min.)
·

Press "→" button: Shift up

·

Press "←" button: Shift down


Used to check the operation of the shift solenoid valves.
NOTICE:

Performing this test at speeds other than those specified under "Vehicle Condition" will damage the transaxle.


HINT:

Perform "Control the Shift Position" while monitoring "Shift Status" to confirm actual gear position.


(Vehicle Condition)
Perform at a vehicle of 20 km/h (12 mph) or more and 45 km/h (28 mph) or less.
Control the SLS Pressure Operates shift solenoid valve SLS High or Low (Vehicle Condition)
Perform with the ignition switch ON and the engine running.
Activate the Solenoid (SLS) Operates shift solenoid valve SLS ON or OFF (Vehicle Condition)
Perform with the ignition switch ON, the engine stopped and the shift lever in P or N.
Activate the Solenoid(SC) Operates shift solenoid valve SC ON or OFF (Vehicle Condition)
Perform with the ignition switch ON, the engine stopped and the shift lever in P or N.
Activate the Solenoid(SLP) Operates shift solenoid valve SLP ON or OFF (Vehicle Condition)
Perform with the ignition switch ON, the engine stopped and the shift lever in P or N.