Home › Drivetrain › K312 CVT › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › 2016.04–2017.10
RM30M0E _52 Drivetrain _052969 K312 CVT _0256556 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K312 CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P0705  Transmission Range Sensor Circuit Malfunction (PRNDL Input)  


DESCRIPTION

The park/neutral position switch and transmission control switch (shift lock control unit assembly) detect the shift lever position and send signals to the ECM.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0705 Transmission Range Sensor Circuit Malfunction (PRNDL Input) When the ignition switch is ON and the battery voltage is 10.5 V or more, any one of the following conditions is met (2 trip detection logic):
·

2 or more signals are ON simultaneously for 2 seconds or more for (NSW, P, N), R, D input signals.

·

NSW, P, R, N, D input signals are all OFF simultaneously for 60 seconds or more.

·

When the S signal (M position switch signal) is ON, any of the NSW, P, R, N input signals is ON simultaneously for 2 seconds or more.


·

Open or short in park/neutral position switch circuit

·

Park/Neutral Position Switch

·

Transmission control switch

(Shift lock control unit assembly)

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

For safety, the park/neutral position switch detects the gearshift position so that engine can be started only when the vehicle is in the P or N shift position.

When the park/neutral position switch and shift lock control unit assembly (transmission control switch) send more than one signal at a time from switch positions P, R, N, D, M, the ECM interprets this as a fault in the switch. The ECM will turn on the MIL and store the DTC.

WIRING DIAGRAM

C342242E13
2.573,1.302 2.729,1.5 0.156,0.198 10 false 4 4.208,1.302 4.844,1.479 0.635,0.177 10 false 9 4.219,2.021 4.375,2.219 0.156,0.198 10 false 3 4.219,2.552 4.375,2.75 0.156,0.198 10 false 2 4.219,3.094 4.375,3.292 0.156,0.198 10 false 8 4.219,3.625 4.375,3.823 0.156,0.198 10 false 7 5.177,0.531 5.49,0.729 0.313,0.198 10 false 15 5.177,1.219 5.49,1.417 0.313,0.198 10 false 17 5.198,1.917 5.51,2.115 0.313,0.198 10 false 25 5.229,2.469 5.385,2.667 0.156,0.198 10 false 8 5.198,3 5.51,3.198 0.313,0.198 10 false 24 5.177,3.531 5.49,3.729 0.313,0.198 10 false 18 5.177,4.792 5.49,4.99 0.313,0.198 10 false 30 2.781,1.302 2.938,1.5 0.156,0.198 10 false B 3.99,1.302 4.146,1.5 0.156,0.198 10 false L 3.896,2.01 4.208,2.208 0.313,0.198 10 false PL 3.906,2.552 4.219,2.75 0.313,0.198 10 false RL 3.896,3.083 4.208,3.281 0.313,0.198 10 false NL 3.896,3.625 4.208,3.823 0.313,0.198 10 false DL 5.521,0.615 5.979,0.813 0.458,0.198 10 false NSW 5.51,1.302 5.969,1.5 0.458,0.198 10 false STA 5.51,2.021 5.667,2.219 0.156,0.198 10 false P 5.51,2.563 5.667,2.76 0.156,0.198 10 false R 5.51,3.073 5.667,3.271 0.156,0.198 10 false N 5.51,3.615 5.667,3.813 0.156,0.198 10 false D 5.51,4.865 5.667,5.063 0.156,0.198 10 false S 2.76,4.865 3.073,5.063 0.313,0.198 10 false IG 3.979,4.885 4.135,5.083 0.156,0.198 10 false S 2.344,4.146 2.802,4.344 0.458,0.198 10 false B19 2.344,4.313 4.51,4.542 2.167,0.229 10 false Park / Neutral Position Switch 2.427,5.323 2.885,5.521 0.458,0.198 10 false F133 2.427,5.5 4.479,5.958 2.052,0.458 10 false Shift Lock Control Unit Assembly (Transmission Control Switch) 2.583,4.865 2.74,5.063 0.156,0.198 10 false 4 4.208,4.885 4.365,5.083 0.156,0.198 10 false 5 0.542,1.198 1.667,1.958 1.125,0.76 10 false from Certification ECU (Smart Key ECU Assembly)*1 0.729,3.063 1.646,3.313 0.917,0.25 10 false ECU-IG NO. 3 5.135,0.708 5.594,0.906 0.458,0.198 10 false B47 5.135,1.396 5.594,1.594 0.458,0.198 10 false B47 5.146,2.104 5.604,2.302 0.458,0.198 10 false B48 5.146,3.177 5.604,3.375 0.458,0.198 10 false B48 5.104,2.646 5.719,2.844 0.615,0.198 10 false F130 5.094,3.719 5.708,3.917 0.615,0.198 10 false F130 5.135,4.969 5.594,5.167 0.458,0.198 10 false B48 5.927,5.635 6.385,5.833 0.458,0.198 10 false ECM 2.573,2.813 2.729,3.01 0.156,0.198 10 false 1 2.771,2.813 3.083,3.01 0.313,0.198 10 false RB 0.5,2.135 1.917,2.552 1.417,0.417 10 false from Ignition or Starter Switch Assembly*2 4.719,6.094 7.125,6.344 2.406,0.25 10 false *1: w/ Smart Entry and Start System 4.719,6.448 7.125,6.698 2.406,0.25 10 false *2: w/o Smart Entry and Start System

CAUTION / NOTICE / HINT

NOTICE:
·

Perform initialization after replacing any parts related to the continuously variable transaxle system.

Click hereDrivetrain>K312 CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K312 CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.READ VALUE USING GTS (NEUTRAL POSITION SW SIGNAL, SHIFT SW STATUS)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.

Powertrain > Engine and ECT > Data List
Tester Display
Neutral Position SW Signal
Shift SW Status (P Range)
Shift SW Status (R Range)
Shift SW Status (N Range)
Shift SW Status (D Range)
50003 234 147,125,126,127,128

e.

According to the display on the GTS, read the Data List.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Neutral Position SW Signal Park/neutral position switch status ON or OFF
·

ON: Shift lever in P or N


·

OFF: Shift lever not in P or N


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
Shift SW Status (P Range) Park/neutral position switch status ON or OFF
·

ON: Shift lever in P


·

OFF: Shift lever not in P


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
Shift SW Status (R Range) Park/neutral position switch status ON or OFF
·

ON: Shift lever in R


·

OFF: Shift lever not in R


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
Shift SW Status (N Range) Park/neutral position switch status ON or OFF
·

ON: Shift lever in N


·

OFF: Shift lever not in N


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
Shift SW Status (D Range) Park/neutral position switch status ON or OFF
·

ON: Shift lever in D or M


·

OFF: Shift lever not in D or M


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.

Result:
Result Proceed to
Data display is within Normal Condition range A
Data display is not within Normal Condition range B



A

2.READ VALUE USING GTS (SPORTS MODE SELECTION SW)

B

6.CHECK HARNESS AND CONNECTOR (BATTERY - PARK/NEUTRAL POSITION SWITCH)
2.READ VALUE USING GTS (SPORTS MODE SELECTION SW)
a.

Enter the following menus: Powertrain / Engine and ECT / Data List.

Powertrain > Engine and ECT > Data List
Tester Display
Sports Mode Selection SW
50003 234 133

b.

According to the display on the GTS, read the Data List.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Sports Mode Selection SW Transmission control switch status ON or OFF
·

ON: Shift lever in M, "+" or "-"

·

OFF: Shift lever not in M, "+" or "-"


-

Result:
Result Proceed to
Data display is within Normal Condition range A
Data display is not within Normal Condition range B



A

B

3.INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY (TRANSMISSION CONTROL SWITCH (POWER SOURCE))
3.INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY (TRANSMISSION CONTROL SWITCH (POWER SOURCE))
a.

Disconnect the F133 transmission control switch connector of the shift lock control unit assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F133-4 (IG) - Body ground Ignition switch ON 11 to 14 V
F133-5 (S) - Body ground Ignition switch off Below 1 V



c.

Connect the F133 transmission control switch connector of the shift lock control unit assembly.


Result:
Proceed to
OK
NG



OK

4.INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY (TRANSMISSION CONTROL SWITCH)

NG

CHECK POWER SOURCE CIRCUIT (TRANSMISSION CONTROL SWITCH)

4.INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY (TRANSMISSION CONTROL SWITCH)
a.
C239095C62
0.771,1.729 1.125,1.313 true 1.906,1.75 1.521,1.323 true 0.198,0.167 0.51,0.365 0.313,0.198 10 false *a 1.906,1.802 2.375,2 0.469,0.198 10 false IG 0.646,1.771 1.021,1.979 0.375,0.208 10 false S
*a Component without harness connected
(Shift Lock Control Unit Assembly (Transmission Control Switch))


Disconnect the F133 shift lock control unit assembly (transmission control switch) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
4 (IG) - 5 (S) Shift lever in M, "+" or "- " Below 1 Ω
Shift lever not in M, "+" or "-" 10 kΩ or higher



c.

Connect the F133 shift lock control unit assembly (transmission control switch) connector.


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (SHIFT LOCK CONTROL UNIT ASSEMBLY (TRANSMISSION CONTROL SWITCH) - ECM)

NG

REPLACE SHIFT LOCK CONTROL UNIT ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (SHIFT LOCK CONTROL UNIT ASSEMBLY (TRANSMISSION CONTROL SWITCH) - ECM)
a.

Disconnect the B48 ECM connector.


b.

Disconnect the F133 shift lock control unit assembly (transmission control switch) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F133-5 (S) - B48-30 (S) Always Below 1 Ω
F133-5 (S) - Body ground Always 10 kΩ or higher
B48-30 (S) - Body ground Always 10 kΩ or higher



d.

Connect the F133 shift lock control unit assembly (transmission control switch) connector.


e.

Connect the B48 ECM connector.


Result:
Proceed to
OK
NG



OK

9.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (BATTERY - PARK/NEUTRAL POSITION SWITCH)
a.
C193930C54
0.083,1.083 0.583,1.333 0.5,0.25 1.677,1.063 2.167,0.417 true 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 0.208,1.125 0.604,1.375 0.396,0.25 10 false B19 2.219,0.302 2.531,0.469 0.313,0.167 10 false RB
*a Front view of wire harness connector
(to Park/Neutral Position Switch)


Disconnect the park/neutral position switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B19-1 (RB) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



c.

Connect the park/neutral position switch connector.


Result:
Proceed to
OK
NG



OK

7.INSPECT PARK/NEUTRAL POSITION SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT PARK/NEUTRAL POSITION SWITCH
a.

Disconnect the B19 park/neutral position switch connector.


b.
C283071C14
1.948,1 2.5,0.49 true 1.938,1 2.49,0.49 true 1.938,1 2.49,0.49 true 1.667,1.021 2.083,0.281 true 1.427,0.99 0.76,0.417 true 1.198,0.99 0.396,0.688 true 1.729,1.375 1.448,1.948 true 1.26,1.375 0.531,1.781 true 1.438,1.375 0.896,1.938 true 0.115,0.094 0.427,0.25 0.313,0.156 10 false *a 2.198,0.177 2.51,0.375 0.313,0.198 10 false RL 2.615,0.396 2.927,0.594 0.313,0.198 10 false RB 0.552,0.333 0.865,0.531 0.313,0.198 10 false PL 0.24,0.615 0.552,0.813 0.313,0.198 10 false B 0.323,1.708 0.635,1.906 0.313,0.198 10 false L 1.26,1.885 1.573,2.083 0.313,0.198 10 false DL 0.698,1.875 1.01,2.073 0.313,0.198 10 false NL
*a Component without harness connected (Park/Neutral Position Switch)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
4 (B) - 9 (L) Shift lever in P or N Below 1 Ω
Shift lever not in P or N 10 kΩ or higher
1 (RB) - 3 (PL) Shift lever in P Below 1 Ω
Shift lever not in P 10 kΩ or higher
1 (RB) - 2 (RL) Shift lever in R Below 1 Ω
Shift lever not in R 10 kΩ or higher
1 (RB) - 8 (NL) Shift lever in N Below 1 Ω
Shift lever not in N 10 kΩ or higher
1 (RB) - 7 (DL) Shift lever in D or M Below 1 Ω
Shift lever not in D or M 10 kΩ or higher



c.

Connect the B19 park/neutral position switch connector.


Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH- ECM)

NG

REPLACE PARK/NEUTRAL POSITION SWITCH

8.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH- ECM)
a.

Disconnect the B47, B48 and F130 ECM connectors.


b.

Disconnect the B19 park/neutral position switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B19-3 (PL) - B48-25 (P) Always Below 1 Ω
B19-2 (RL) - F130-8 (R) Always Below 1 Ω
B19-8 (NL) - B48-24 (N) Always Below 1 Ω
B19-7 (DL) - F130-18 (D) Always Below 1 Ω
B19-4 (B) - B47-15 (NSW) Always Below 1 Ω
B19-3 (PL) or B48-25 (P) - Body ground and other terminals Always 10 kΩ or higher
B19-2 (RL) or F130-8 (R) - Body ground and other terminals Always 10 kΩ or higher
B19-8 (NL) or B48-24 (N) - Body ground and other terminals Always 10 kΩ or higher
B19-7 (DL) or F130-18 (D) - Body ground and other terminals Always 10 kΩ or higher
B19-4 (B) or B47-15 (NSW) - Body ground and other terminals Always 10 kΩ or higher



d.

Connect the B19 park/neutral position switch connector.


e.

Connect the B47, B48 and F130 ECM connectors.


Result:
Proceed to
OK
NG



OK

9.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.REPLACE ECM

Result:
Proceed to
NEXT



NEXT