Home › Drivetrain › K312 CVT › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › from 2016.04
RM30M0E _52 Drivetrain _052969 K312 CVT _0256556 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K312 CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P0712  Transmission Fluid Temperature Sensor "A" Circuit Low Input  P0713  Transmission Fluid Temperature Sensor "A" Circuit High Input  


DESCRIPTION

The CVT fluid temperature sensor converts the CVT fluid temperature into a resistance value for use by the ECM.

The sensor resistance changes with the CVT fluid temperature. As the temperature rises, the sensor resistance decreases. The ECM applies voltage to the temperature sensor through ECM terminal THO1 and calculates the fluid temperature based on the voltage signal.

HINT:

The CVT fluid temperature is likely to increase under conditions such as towing, climbing hills and in traffic.


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0712 Transmission Fluid Temperature Sensor "A" Circuit Low Input There is a short in the CVT fluid temperature sensor circuit for 0.5 seconds (1 trip detection logic).
·

Wire harness or connector

·

Continuously variable transaxle assembly (CVT fluid temperature sensor)

·

ECM


Comes on DTC stored
P0713 Transmission Fluid Temperature Sensor "A" Circuit High Input Either one of the following conditions is met (1 trip detection logic):
·

When 10 seconds or more have elapsed after engine start (engine coolant and intake air temperatures at engine start were higher than -29.375°C (-20.875°F), there is an open in the CVT fluid temperature sensor circuit for more than 0.5 seconds.

·

When 15 minutes or more have elapsed after engine start (engine coolant and intake air temperatures were lower than -29.375°C (-20.875°F) at engine start, there is an open in the CVT fluid temperature sensor circuit for 0.5 seconds.


·

Wire harness or connector

·

Continuously variable transaxle assembly (CVT fluid temperature sensor)

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

The CVT fluid temperature sensor converts the CVT fluid temperature to an electrical resistance value. Based on the resistance, the ECM determines the CVT fluid temperature and can detect an open or short in the CVT fluid temperature circuit. If the resistance value of the CVT fluid temperature is less than 79 Ω*1 or more than 156 kΩ*2, the ECM interprets this as a malfunction of the CVT fluid temperature sensor or wiring, illuminates the MIL and stores a DTC.

*1: 150°C (302°F) or more is indicated regardless of the actual CVT fluid temperature.

*2: -40°C (-40°F) is indicated regardless of the actual CVT fluid temperature.

HINT:

The CVT fluid temperature can be checked in the Data List.


WIRING DIAGRAM

C318996E16
1.49,1.74 3.458,1.927 1.969,0.188 10 false CVT Fluid Temperature Sensor 1.823,2.729 3.656,2.927 1.833,0.198 10 false Transmission Wire 0.833,3.208 3.625,3.406 2.792,0.198 10 false Continuously Variable Transaxle Assembly 6.052,3.313 6.969,3.656 0.917,0.344 10 false ECM 3.552,1.167 4.01,1.365 0.458,0.198 10 false THO 3.656,2.135 4.115,2.333 0.458,0.198 10 false E2 3.885,2.135 4.344,2.333 0.458,0.198 10 false 7 3.896,1.167 4.354,1.365 0.458,0.198 10 false 1 5.281,1.146 5.74,1.344 0.458,0.198 10 false 20 5.583,1.167 6.042,1.365 0.458,0.198 10 false THO1 5.583,2.135 6.042,2.333 0.458,0.198 10 false ETHO 5.292,2.135 5.75,2.333 0.458,0.198 10 false 21 6.281,0.979 6.74,1.177 0.458,0.198 10 false 5 V 1.823,2.594 2.26,2.802 0.438,0.208 10 false B53 6.052,3.167 6.625,3.438 0.573,0.271 10 false B48

CAUTION / NOTICE / HINT

NOTICE:
·

Perform initialization after replacing any parts related to the continuously variable transaxle system.

Click hereDrivetrain>K312 CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION


·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K312 CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.INSPECT TRANSMISSION WIRE (CVT FLUID TEMPERATURE SENSOR)
a.
C264597C31
2.521,0.885 2.844,0.635 true 2.531,1.188 2.927,1.49 true 0.198,0.219 0.51,0.417 0.313,0.198 10 *a 2.917,0.563 3.333,0.729 0.417,0.167 10 THO 2.979,1.427 3.292,1.625 0.313,0.198 10 E2
*a Component without harness connected
(Transmission Wire)


Disconnect the B53 transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (THO) - 7 (E2) Always 79 Ω to 156 kΩ
1 (THO) - Body ground and other terminals Always 10 kΩ or higher
7 (E2) - Body ground and other terminals Always 10 kΩ or higher


HINT:

If the resistance is out of the specified range at any of the CVT fluid temperatures shown in the table below, the driveability of the vehicle may decrease.

CVT Fluid Temperature Specified Condition
10°C (50°F) 5 to 8 kΩ
25°C (77°F) 2.5 to 4.5 kΩ
110°C (230°F) 0.22 to 0.28 kΩ



c.

Connect the B53 transmission wire connector.


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

NG

4.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
a.

Disconnect the B48 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B48-20 (THO1) - B48-21 (ETHO) Always 79 Ω to 156 kΩ
B48-20 (THO1) - Body ground and other terminals Always 10 kΩ or higher
B48-21 (ETHO) - Body ground and other terminals Always 10 kΩ or higher



c.

Connect the B48 ECM connector.


Result:
Proceed to
OK
NG



OK

3.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

4.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
a.

Replace the continuously variable transaxle assembly.

Click hereDrivetrain>K312 CVT>CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY>COMPONENTS


Result:
Proceed to
NEXT



NEXT