Home › Drivetrain › K312 CVT › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › 2016.04–2017.10
RM30M0E _52 Drivetrain _052969 K312 CVT _0256556 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM D

K312 CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  INITIALIZATION  


RESET MEMORY/CALIBRATION


NOTICE:
·

Performing Reset Memory will clear the learned values of the yaw rate and acceleration sensor (Deceleration Sensor Zero Point Calibration) and the CVT oil pressure (CVT Oil Pressure Calibration). Make sure to perform Reset Memory, Deceleration Sensor Zero Point Calibration, and CVT Oil Pressure Calibration if any of the parts in the following table have been replaced.

Replaced Part
·

Continuously variable transaxle assembly

·

ECM

·

Oil pressure sensor

·

Airbag ECU assembly (Yaw rate and acceleration sensor)*1

·

Brake actuator assembly (Skid control ECU)*2

·

Deceleration sensor assembly*2



·

After performing Reset Memory, always perform Deceleration Sensor Zero Point Calibration first, and then CVT Oil Pressure Calibration.

*1: w/ VSC

*2: w/o VSC




a.

Perform Reset Memory

i.

Turn the ignition switch off.


ii.

Move the shift lever to P and apply the parking brake.


iii.

Connect the GTS to the DLC3.


iv.

Turn the ignition switch to ON.

NOTICE:

Do not start the engine.



v.

Turn the GTS on.


vi.

Enter the following menus: Powertrain / Engine and ECT / Utility / Reset Memory.

Powertrain > Engine > Utility
Tester Display
Reset Memory
50005 234 176
NOTICE:
·

Make sure the shift lever is in P.

·

Make sure that the engine is stopped. To prevent idling vibrations, do not start the engine.

·

Make sure that the ignition switch is ON.





b.

Perform Deceleration Sensor Zero Point Calibration

i.

Turn the ignition switch to ON and wait at least 2 seconds.


ii.

Enter the following menus: Powertrain / Engine and ECT / Utility / Deceleration Sensor Zero Point Calibration.

Powertrain > Engine > Utility
Tester Display
Deceleration Sensor Zero Point Calibration
50005 234 2123
NOTICE:

Keep the vehicle stopped, level and stable during calibration (Inclination: 0 +/- 0.25°).


HINT:
·

When "Complete" is displayed on the screen, Deceleration Sensor Zero Point Calibration is complete.

·

If "Error" is displayed on the screen and DTC P1589 is output (for the detection conditions for DTC P1589), refer to P1589, the deceleration sensor circuit may be malfunctioning.

Click hereDrivetrain>K312 CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>P1589

·

Shaking or vibrating the vehicle during Deceleration Sensor Zero Point Calibration may cancel calibration. If "Error" is displayed on the screen and DTC P1589 is not output, perform calibration again.





c.

Perform CVT Oil Pressure Calibration

i.

Turn the ignition switch off and wait at least 30 seconds.


ii.

Turn the ignition switch to ON and wait at least 2 seconds.

NOTICE:

Do not start the engine.


HINT:

CVT Oil Pressure Sensor Zero Point Calibration is performed when the ignition switch is turned ON (engine stopped). However, CVT Oil Pressure Sensor Zero Point Calibration will not be performed under the following conditions:

·

Oil pressure sensor value is 0.065 MPa (0.663 kgf/cm2, 9.43 psi) or more.

·

CVT oil temperature is -5°C (23°F) or less or 120°C (248°F) or more.




iii.

Start the engine and wait at least 5 seconds.


iv.

Enter the following menus: Powertrain / Engine and ECT / Utility / CVT Oil Pressure Calibration.

Powertrain > Engine > Utility
Tester Display
CVT Oil Pressure Calibration
50005 234 2122
HINT:
·

During CVT Oil Pressure Calibration, the engine idle speed will increase.

·

When "Complete" is displayed on the screen, CVT Oil Pressure Calibration is complete.

·

The learned values cannot be cleared by only disconnecting and reconnecting the cable to the negative (-) battery terminal.