Home › Drivetrain › K312 CVT › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › from 2016.04
RM30M0E _52 Drivetrain _052969 K312 CVT _0256556 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K312 CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P0717  Input/Turbine Speed Sensor "A" Circuit No Signal  P07BF  Input/Turbine Speed Sensor "A" Circuit Low  P07C0  Input/Turbine Speed Sensor "A" Circuit High  


DESCRIPTION

The ECM receives a signal from the transmission revolution sensor (NT) installed to the continuously variable transaxle to control the lock-up engagement pressure and forward and reverse clutch pressure.

The transmission revolution sensor (NT) detects the input turbine speed and sends a signal to the ECM.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0717 Input/Turbine Speed Sensor "A" Circuit No Signal All of the following conditions are met (1 trip detection logic):
·

Vehicle is driven with the shift lever in D

·

Output shaft speed is 300 rpm or more

·

No malfunctions are found in the park/neutral position switch

·

Input turbine speed indicated by the transmission revolution sensor (NT) is less than 300 rpm for 2 seconds


·

Wire harness or connector

·

Continuously variable transaxle assembly (Transmission revolution sensor (NT))

·

ECM


Comes on DTC stored
P07BF Input/Turbine Speed Sensor "A" Circuit Low There is no malfunction in transmission revolution sensor (NT) signals, and the transmission revolution sensor (NT) output voltage is less than 0.2 V for 2 seconds (1 trip detection logic).
·

Wire harness or connector

·

Continuously variable transaxle assembly (Transmission revolution sensor (NT))

·

ECM


Comes on DTC stored
P07C0 Input/Turbine Speed Sensor "A" Circuit High There is no malfunction in transmission revolution sensor (NT) signals, and the transmission revolution sensor (NT) output voltage is higher than 1.8 V for 2 seconds (1 trip detection logic).
·

Wire harness or connector

·

Continuously variable transaxle assembly (Transmission revolution sensor (NT))

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

The transmission revolution sensor (NT) is used to detect the input turbine speed. The ECM determines the necessary gear ratio based on a comparison of the transmission revolution sensor (NT) (input turbine speed) and transmission revolution sensor (NOUT) (output shaft speed) signals.

When the output shaft speed is higher than the expected value and the input turbine speed is less than 300 rpm while driving with the shift lever in D, the ECM will determine that the transmission revolution sensor (NT) is malfunctioning, illuminate the MIL and store a DTC.

WIRING DIAGRAM

C342243E03
6.375,2.802 6.833,3 0.458,0.198 10 false ECM 3.854,0.677 4.313,0.875 0.458,0.198 10 false NTB 3.875,1.552 4.333,1.75 0.458,0.198 10 false NTO 6.083,0.667 6.542,0.865 0.458,0.198 10 false NTB 6.125,1.552 6.583,1.75 0.458,0.198 10 false NTO 6.167,2.469 6.479,2.667 0.313,0.198 10 false E1 0.583,2 2.115,2.583 1.531,0.583 10 false Transmission Revolution Sensor (NT) 2.667,1.969 3.125,2.167 0.458,0.198 10 false B53 2.656,2.115 4.031,2.396 1.375,0.281 10 false Transmission Wire 0.75,3 3.708,3.417 2.958,0.417 10 false Continuously Variable Transaxle Assembly 4.26,0.667 4.417,0.865 0.156,0.198 10 false 2 4.25,1.552 4.406,1.75 0.156,0.198 10 false 8 5.833,0.583 6.146,0.781 0.313,0.198 10 false 29 5.823,1.5 6.135,1.698 0.313,0.198 10 false 19 5.844,2.333 6,2.531 0.156,0.198 10 false 3 5.771,0.771 6.229,0.969 0.458,0.198 10 false B48 5.781,1.677 6.24,1.875 0.458,0.198 10 false B48 5.781,2.521 6.24,2.719 0.458,0.198 10 false B46 6.698,0.5 7.156,0.698 0.458,0.198 10 false 12 V

CAUTION / NOTICE / HINT

NOTICE:
·

Perform initialization after replacing any parts related to the continuously variable transaxle system.

Click hereDrivetrain>K312 CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION


·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K312 CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.READ VALUE USING GTS (SPD (NT) AND NT SENSOR VOLTAGE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.


e.

According to the display on the GTS, read the Data List.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
SPD (NT) Input turbine speed (NT) Min.: 0 rpm
Max.: 12750 rpm
·

Input turbine speed (NT) equal to engine speed (NE): Lock-up ON (After warming up engine)

·

Input turbine speed (NT) nearly equal to engine speed (NE): Lock-up OFF (Idling with shift lever in P or N)

·

0 rpm: Vehicle stopped with shift lever in D


Data is displayed in increments of 50 rpm.
NT Sensor Voltage Transmission revolution sensor (NT) output voltage Min.: 0.000 V
Max.: 4.999 V
0.6 to 1.5 V: Engine idling (Vehicle stopped with shift lever in P or N) -
Powertrain > Engine and ECT > Data List
Tester Display
SPD (NT)
NT Sensor Voltage
50003 234 390,391

Result:
Result Proceed to
Data List value is not normal A
Data List value is normal B



A

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

B

5.REPLACE ECM
2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
a.

Disconnect the B53 transmission wire connector.


b.

Disconnect the B48 and B46 ECM connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B53-8 (NTO) - B48-19 (NTO) Always Below 1 Ω
B53-2 (NTB) - B48-29 (NTB) Always Below 1 Ω
B46-3 (E1) - Body ground Always Below 1 Ω
B53-8 (NTO) or B48-19 (NTO) - Body ground and other terminals Always 10 kΩ or higher
B53-2 (NTB) or B48-29 (NTB) - Body ground and other terminals Always 10 kΩ or higher



d.

Connect the B48 and B46 ECM connectors.


e.

Connect the B53 transmission wire connector.


Result:
Proceed to
OK
NG



OK

3.CHECK ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK ECM
a.
C265778C22
0.083,1.031 0.583,1.281 0.5,0.25 1.021,0.26 1.292,0.99 true 0.208,1.073 0.667,1.271 0.458,0.198 10 false B53 0.688,0.177 1.146,0.375 0.458,0.198 10 false NTB 0.104,0.094 0.417,0.292 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Transmission Wire)


Disconnect the transmission wire connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B53-2 (NTB) - Body ground Ignition switch ON 11 to 14 V



d.

Turn the ignition switch off.


e.

Connect the transmission wire connector.


f.
C342244C01
1.021,2.406 0.625,1.688 true 2.292,2.427 1.906,1.802 true 0.104,0.135 0.417,0.333 0.313,0.198 10 false *a 1.104,2.333 1.542,2.573 0.438,0.24 10 false 3 (E1) 2.375,2.344 3.094,2.542 0.719,0.198 10 false 19 (NTO)
*a Component without harness connected
(ECM)


Disconnect the B48 and B46 ECM connectors.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B48-19 (NTO) - B46-3 (E1) Always 99 to 101 Ω



h.

Connect the B48 and B46 ECM connectors.


Result:
Proceed to
OK
NG



OK

4.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

NG

5.REPLACE ECM
4.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
a.

Replace the continuously variable transaxle assembly.

Click hereDrivetrain>K312 CVT>CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY>COMPONENTS


Result:
Proceed to
NEXT



NEXT

5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT