The ECM performs learning control for the belt clamping pressure based on the belt clamping pressure signal, which is output by the oil pressure sensor.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0842 | Transmission Fluid Pressure Sensor/Switch "A" Circuit Low | When 2 seconds or more have elapsed after engine start, there is a short in the oil pressure sensor circuit for 0.5 seconds (1 trip detection logic). | ·
Wire harness or connector ·
Oil pressure sensor ·
ECM |
Does not come on | DTC stored |
| P0843 | Transmission Fluid Pressure Sensor/Switch "A" Circuit High | When 2 seconds or more have elapsed after engine start, there is an open or a short to +B in the oil pressure sensor circuit for 0.5 seconds (1 trip detection logic). | ·
Wire harness or connector ·
Oil pressure sensor ·
ECM |
Does not come on | DTC stored |
These DTCs indicate an open or short in the oil pressure sensor. When there is an open or short circuit in the oil pressure sensor circuit, the ECM detects the problem and stores a DTC.
Perform initialization after replacing any parts related to the continuously variable transaxle system.
Click hereDrivetrain>K312 CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION
Check that no DTCs are stored after performing initialization.
Click hereDrivetrain>K312 CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
Do not perform a stall test if there are any people or objects near the vehicle.
Do not perform a stall test if any wheel chocks are out of position.
Do not perform the stall test on a slippery or low-friction surface that could allow the tires to spin.
This test must be performed after checking and confirming that the engine is normal.
Perform this test with the CVT fluid temperature between 50 and 100°C (122 and 212°F).
Perform this test with the air conditioning off.
Do not perform the stall speed test for longer than 5 seconds.
When performing the stall speed test more than once, make sure to wait 15 seconds or more between tests.
Warm up the engine.
Fully apply the parking brake and chock all 4 wheels.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Connect the TC and TE1.
| Active Test Display |
|---|
| Connect the TC and TE1 |
| Data List Display |
|---|
| A/T Oil Pressure |
Observe "A/T Oil Pressure" in the Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| A/T Oil Pressure | Secondary oil pressure value | Min.: -64 MPa
Max.: 63.998 MPa |
Secondary oil pressure inspection:
·
4.2 to 4.9 MPa(42.8 to 50.0 kgf/cm2, 609 to 711 psi): D position stall test ·
4.0 to 5.1 MPa(40.8 to 52.0 kgf/cm2, 580 to 740 psi): R position stall test |
- |
| Result | Proceed to |
|---|---|
| Data List value is not normal | A |
| Data List value is normal | B |
A
B
Disconnect the B49 oil pressure sensor connector.
Disconnect the F130 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B49-1 (E2) - F130-31 (EPTO) | Always | Below 1 Ω |
| B49-2 (PTO) - F130-24 (PTO) | Always | Below 1 Ω |
| B49-3 (VC) - F130-32 (VCPT) | Always | Below 1 Ω |
| B49-1 (E2) or F130-31 (EPTO) - Body ground and other terminals | Always | 10 kΩ or higher |
| B49-2 (PTO) or F130-24 (PTO) - Body ground and other terminals | Always | 10 kΩ or higher |
| B49-3 (VC) or F130-32 (VCPT) - Body ground and other terminals | Always | 10 kΩ or higher |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F130-24 (PTO) - Body ground | Ignition switch ON | Below 1 V |
| B49-2 (PTO) - Body ground | Ignition switch ON | Below 1 V |
Connect the F130 ECM connector.
Connect the B49 oil pressure sensor connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Oil Pressure Sensor) |
Disconnect the oil pressure sensor connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| B49-3 (VC) - B49-1 (E2) | Ignition switch ON | 4.75 to 5.25 V |
Connect the oil pressure sensor connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the oil pressure sensor.
Click hereDrivetrain>K312 CVT>OIL PRESSURE SENSOR>COMPONENTS
| Proceed to |
|---|
| NEXT |
NEXT
Replace the ECM.
Click hereEngine / Hybrid System>2NR-FE ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT