Home › Drivetrain › K312 CVT › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › from 2016.04
RM30M0E _52 Drivetrain _052969 K312 CVT _0256556 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K312 CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P099B  Shift Solenoid "G" Control Circuit Low (Shift Solenoid Valve SC)  P099C  Shift Solenoid "G" Control Circuit High (Shift Solenoid Valve SC)  


DESCRIPTION

Based on the signal received by the shift solenoid valve SC, the ECM uses the shift solenoid valve SLU to control the forward and reverse clutch pressure.

If there is an open or short in the shift solenoid valve SC circuit, the ECM stops sending current to the malfunctioning shift solenoid valve.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P099B Shift Solenoid "G" Control Circuit Low (Shift Solenoid Valve SC) While the vehicle is driven, there is a short in the shift solenoid valve SC circuit for 3 seconds (1 trip detection logic).
·

Wire harness or connector

·

Continuously variable transaxle assembly (Shift solenoid valve SC)

·

ECM


Comes on DTC stored
P099C Shift Solenoid "G" Control Circuit High (Shift Solenoid Valve SC) While the vehicle is driven, there is an open in the shift solenoid valve SC circuit for 0.5 seconds (1 trip detection logic).
·

Wire harness or connector

·

Continuously variable transaxle assembly (Shift solenoid valve SC)

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

These DTCs indicate an open or short in the shift solenoid valve SC circuit. If there is an open or short in the shift solenoid valve SC circuit, the ECM detects the malfunction, illuminates the MIL and stores a DTC.

WIRING DIAGRAM

C328134E09
0.313,1.698 1.979,1.99 1.667,0.292 10 false Shift Solenoid Valve SC 2.885,2.427 3.344,2.625 0.458,0.198 10 false B53 2.885,2.594 4.719,2.792 1.833,0.198 10 false Transmission Wire 0.969,3.271 3.833,3.563 2.865,0.292 10 false Continuously Variable Transaxle Assembly 4.177,1.385 4.49,1.583 0.313,0.198 10 false SC 4.51,1.396 4.667,1.594 0.156,0.198 10 false 9 5.448,1.385 5.76,1.583 0.313,0.198 10 false 11 5.708,1.396 6.021,1.594 0.313,0.198 10 false SC 6.333,1.083 6.792,1.281 0.458,0.198 10 false 12 V 6.104,3.333 6.719,3.531 0.615,0.198 10 false B48 6.104,3.5 6.615,3.781 0.51,0.281 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:
·

Perform initialization after replacing any parts related to the continuously variable transaxle system.

Click hereDrivetrain>K312 CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION


·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K312 CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SC)
a.
C264597C32
2.063,1.177 2.51,1.677 true 0.198,0.219 0.51,0.417 0.313,0.198 10 *a 2.594,1.635 2.906,1.833 0.313,0.198 10 SC
*a Component without harness connected
(Transmission Wire)


Disconnect the B53 transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
9 (SC) - Body ground 20°C (68°F) 11 to 15 Ω



c.

Connect the B53 transmission wire connector.


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

NG

4.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
a.

Disconnect the B48 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B48-11 (SC) - Body ground 20°C (68°F) 11 to 15 Ω



c.

Connect the B48 ECM connector.


Result:
Proceed to
OK
NG



OK

3.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

4.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
a.

Replace the continuously variable transaxle assembly.

Click hereDrivetrain>K312 CVT>CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY>COMPONENTS


Result:
Proceed to
NEXT



NEXT