Home › Drivetrain › K312 CVT › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › from 2016.04
RM30M0E _52 Drivetrain _052969 K312 CVT _0256556 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K312 CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P2822  Pressure Control Solenoid "J" Electrical (Shift Solenoid Valve SLP)  


DESCRIPTION

According to current from the ECM, the shift solenoid valve SLP controls primary pulley pressure in accordance with the requested gear ratio to perform gear ratio changes.

C300481C04
4.677,1.552 4.125,0.49 4.125,0.49 3.906,0.49 true 4.5,1.75 4.125,2.344 4.125,2.344 3.906,2.344 true 5.438,1.844 5.125,2.344 5.125,2.344 4.906,2.344 true 5.125,2.323 5.427,1.292 true 0.792,1.229 1.042,1.417 0.25,0.188 10 false *a 1.583,1.99 2.01,2.188 0.427,0.198 10 false *b 3.729,0.427 4.042,0.625 0.313,0.198 10 false *1 3.729,2.281 4.042,2.479 0.313,0.198 10 false *2 4.708,2.281 5.021,2.479 0.313,0.198 10 false *3
*1 Spool Valve *2 Sleeve
*3 Solenoid Coil - -
*a Hydraulic Pressure *b Current Flow to Solenoid


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2822 Pressure Control Solenoid "J" Electrical (Shift Solenoid Valve SLP) While the vehicle is driven, an open or a short is detected in the shift solenoid valve SLP circuit for 1 second or more (1 trip detection logic).
·

Wire harness or connector

·

Continuously variable transaxle assembly (Shift solenoid valve SLP)

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

This DTC indicates an open or short in the shift solenoid valve SLP circuit. If there is an open or short in the shift solenoid valve SLP circuit, the ECM detects the malfunction, illuminates the MIL and stores this DTC.

WIRING DIAGRAM

C328132E14
0.26,1.604 2.052,1.833 1.792,0.229 10 false Shift Solenoid Valve SLP 4.323,0.99 4.938,1.188 0.615,0.198 10 false SLP+ 4.771,0.99 4.927,1.188 0.156,0.198 10 false 4 5.198,0.979 5.406,1.198 0.208,0.219 10 false 7 4.323,1.958 4.938,2.156 0.615,0.198 10 false SLP- 5.427,0.99 6.042,1.188 0.615,0.198 10 false SLP+ 5.427,1.958 6.042,2.156 0.615,0.198 10 false SLP- 4.76,1.958 5.073,2.156 0.313,0.198 10 false 11 5.208,1.958 5.448,2.167 0.24,0.208 10 false 6 2.729,2.448 3.188,2.646 0.458,0.198 10 false B53 2.729,2.604 4.01,2.865 1.281,0.26 10 false Transmission Wire 1.115,3.073 3.906,3.313 2.792,0.24 10 false Continuously Variable Transaxle Assembly 5.875,3.031 6.49,3.229 0.615,0.198 10 false B48 5.875,3.188 6.375,3.406 0.5,0.219 10 false ECM 6,0.74 6.615,0.938 0.615,0.198 10 false 12 V

CAUTION / NOTICE / HINT

NOTICE:
·

Perform initialization after replacing any parts related to the continuously variable transaxle system.

Click hereDrivetrain>K312 CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION


·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K312 CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SLP)
a.
C264597C35
0.958,0.375 1.51,0.906 true 1.031,1.635 1.51,1.156 true 0.198,0.219 0.51,0.417 0.313,0.198 10 false *a 0.635,1.552 1.063,1.75 0.427,0.198 10 false SLP- 0.552,0.323 1.094,0.49 0.542,0.167 10 false SLP+
*a Component without harness connected
(Transmission Wire)


Disconnect the B53 transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (SLP+) - 11 (SLP-) 20°C (68°F) 5.0 to 5.6 Ω
4 (SLP+) - Body ground and other terminals Always 10 kΩ or higher
11 (SLP-) - Body ground and other terminals Always 10 kΩ or higher



c.

Connect the B53 transmission wire connector.


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

NG

4.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
a.

Disconnect the B48 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B48-7 (SLP+) - B48-6 (SLP-) 20°C (68°F) 5.0 to 5.6 Ω
B48-7 (SLP+) - Body ground and other terminals Always 10 kΩ or higher
B48-6 (SLP-) - Body ground and other terminals Always 10 kΩ or higher



c.

Connect the B48 ECM connector.


Result:
Proceed to
OK
NG



OK

3.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

4.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
a.

Replace the continuously variable transaxle assembly.

Click hereDrivetrain>K312 CVT>CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY>COMPONENTS


Result:
Proceed to
NEXT



NEXT