Home › Drivetrain › K312 CVT › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › from 2016.04
RM30M0E _52 Drivetrain _052969 K312 CVT _0256556 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K312 CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P282B  Pressure Control Solenoid "K" Electrical (Shift Solenoid Valve SLS)  


DESCRIPTION

According to current from the ECM, the shift solenoid valve SLS controls secondary pulley pressure and belt clamping pressure in accordance with the input shaft torque.

C267073C01
5.094,0.646 4.875,0.188 4.875,0.188 4.729,0.188 true 4.75,0.885 4.625,1.083 4.625,1.083 4.198,1.083 true 5.885,0.396 5.26,1.313 5.26,1.313 5.896,0.969 true 1.969,1.385 2.26,1.615 0.292,0.229 10 false *b 1.177,0.542 1.385,0.792 0.208,0.25 10 false *a 4.583,0.104 4.781,0.313 0.198,0.208 10 false *1 4.01,1 4.229,1.188 0.219,0.188 10 false *2 5.073,1.24 5.292,1.479 0.219,0.24 10 false *3
*1 Spool Valve *2 Sleeve
*3 Solenoid Coil - -
*a Hydraulic Pressure *b Current Flow to Solenoid


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P282B Pressure Control Solenoid "K" Electrical (Shift Solenoid Valve SLS) While the vehicle is driven, an open or a short is detected in the shift solenoid valve SLS circuit for 1 second or more (1 trip detection logic).
·

Wire harness or connector

·

Continuously variable transaxle assembly (Shift solenoid valve SLS)

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

This DTC indicates an open or short in the shift solenoid valve SLS circuit. If there is an open or short in the shift solenoid valve SLS circuit, the ECM detects the malfunction, illuminates the MIL and stores this DTC.

WIRING DIAGRAM

C328132E15
0.26,1.583 1.885,1.802 1.625,0.219 10 false Shift Solenoid Valve SLS 4.313,0.979 4.927,1.177 0.615,0.198 10 false SLS+ 4.771,0.979 4.927,1.177 0.156,0.198 10 false 5 5.427,0.979 6.042,1.177 0.615,0.198 10 false SLS+ 5.208,0.979 5.375,1.208 0.167,0.229 10 false 5 4.323,1.948 4.938,2.146 0.615,0.198 10 false SLS- 4.771,1.948 5.083,2.146 0.313,0.198 10 false 12 5.198,1.948 5.396,2.167 0.198,0.219 10 false 4 5.448,1.958 6.063,2.156 0.615,0.198 10 false SLS- 2.729,2.438 3.188,2.635 0.458,0.198 10 false B53 2.729,2.594 4.031,2.813 1.302,0.219 10 false Transmission Wire 5.979,0.74 6.594,0.938 0.615,0.198 10 false 12 V 1.031,3.052 3.792,3.302 2.76,0.25 10 false Continuously Variable Transaxle Assembly 5.896,3.042 6.323,3.219 0.427,0.177 10 false B48 5.896,3.198 6.292,3.438 0.396,0.24 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:
·

Perform initialization after replacing any parts related to the continuously variable transaxle system.

Click hereDrivetrain>K312 CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION


·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K312 CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SLS)
a.
C264597C36
0.875,0.479 1.292,0.906 true 0.844,1.604 1.302,1.167 true 0.198,0.219 0.51,0.417 0.313,0.198 10 false *a 0.458,1.531 0.896,1.74 0.438,0.208 10 false SLS- 0.479,0.406 1.094,0.604 0.615,0.198 10 false SLS+
*a Component without harness connected
(Transmission Wire)


Disconnect the B53 transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (SLS+) - 12 (SLS-) 20°C (68°F) 5.0 to 5.6 Ω
5 (SLS+) - Body ground and other terminals Always 10 kΩ or higher
12 (SLS-) - Body ground and other terminals Always 10 kΩ or higher



c.

Connect the B53 transmission wire connector.


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

NG

4.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
a.

Disconnect the B48 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B48-5 (SLS+) - B48-4 (SLS-) 20°C (68°F) 5.0 to 5.6 Ω
B48-5 (SLS+) - Body ground and other terminals Always 10 kΩ or higher
B48-4 (SLS-) -Body ground and other terminals Always 10 kΩ or higher



c.

Connect the B48 ECM connector.


Result:
Proceed to
OK
NG



OK

3.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

4.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
a.

Replace the continuously variable transaxle assembly.

Click hereDrivetrain>K312 CVT>CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY>COMPONENTS


Result:
Proceed to
NEXT



NEXT