The ECM stores this DTC if Deceleration Sensor Zero Point Calibration is not performed or has failed after system components such as the ECM have been replaced.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P1589 | Acceleration Sensor Learning Value | Either one of the following conditions is met (1 trip detection logic):
·
When the vehicle speed is 2 km/h (1.2 mph) or more, Deceleration Sensor Zero Point Calibration has not been completed. ·
While Deceleration Sensor Zero Point Calibration is performed, the learned values of Deceleration Sensor Zero Point Calibration are abnormal (out of normal range). |
·
Deceleration Sensor Zero Point Calibration has not been performed. ·
Vehicle was not stable during Deceleration Sensor Zero Point Calibration. ·
Airbag sensor assembly (Yaw rate and acceleration sensor)*1 ·
Deceleration sensor assembly*2 ·
ECM |
Does not come on | DTC stored |
*1 w/ VSC
*2 w/o VSC
Perform initialization after replacing any parts related to the continuously variable transaxle system.
Click hereDrivetrain>K312 CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION
Check that no DTCs are stored after performing initialization.
Click hereDrivetrain>K312 CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
If CVT Oil Pressure Calibration is performed before Deceleration Sensor Zero Point Calibration, DTC P1589 will be stored. In this case, perform steps *1, *2, *3, *4 and *5 to return the system to normal.
Always perform calibration with the vehicle on level ground (Inclination: 0 +/- 0.25°).
Do not shake or vibrate the vehicle during calibration.
Turn the ignition switch off.*1
Move the shift lever to P and apply the parking brake.*2
Connect the GTS to the DLC3.
Turn the ignition switch to ON.*3
Do not start the engine.
Enter the following menus: Powertrain / Engine and ECT / Utility / Reset Memory.*4
| Tester Display |
|---|
| Reset Memory |
Enter the following menus: Powertrain / ECT / Utility / Deceleration Sensor Zero Point Calibration.*5
| Tester Display |
|---|
| Deceleration Sensor Zero Point Calibration |
When "Complete" is displayed on the screen, Deceleration Sensor Zero Point Calibration is complete.
If "Error" is displayed on the screen, there may be a malfunction in the airbag sensor assembly (yaw rate and acceleration sensor) circuit.
Shaking or vibrating the vehicle during Deceleration Sensor Zero Point Calibration may cancel calibration. If "Error" is displayed on the screen, perform step *5 again.
If "Error" is displayed on the GTS, read the DTCs using the GTS.
Click hereDrivetrain>K312 CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| Deceleration Sensor Zero Point Calibration is completed normally | A |
| DTC P1589 is output (w/ VSC) | B |
| DTC P1589 is output (w/o VSC) | C |
A
B
C
Do not perform Reset Memory and clear the learned values.
Turn the ignition switch off and wait at least 30 seconds.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and wait at least 2 seconds.
Do not start the engine.
CVT Oil Pressure Sensor Zero Point Calibration is performed when the ignition switch is turned ON (engine stopped). However, CVT Oil Pressure Sensor Zero Point Calibration will not be performed under the following conditions:
Oil pressure sensor value is 0.065 MPa (0.663 kgf/cm2, 9.43 psi) or more.
CVT oil temperature is 0°C (32°F) or less or 120°C (248°F) or more.
Start the engine and wait at least 5 seconds.
Start the engine with the shift lever in P.
After starting the engine, do not operate the accelerator pedal.
Enter the following menus: Powertrain / Engine and ECT / Utility / CVT Oil Pressure Calibration
| Tester Display |
|---|
| CVT Oil Pressure Calibration |
When performing CVT Oil Pressure Calibration, the engine idle speed will increase.
When "Complete" is displayed on the screen, CVT Oil Pressure Calibration is complete.
The learned values cannot be cleared by only disconnecting and reconnecting the cable to the negative (-) battery terminal.
Check for DTCs again.
Click hereDrivetrain>K312 CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| NEXT |
NEXT
Check the airbag ECU assembly (yaw rate and acceleration sensor) for any inclination, bracket deformation or installation clearance.
The airbag ECU assembly (yaw rate and acceleration sensor) is installed correctly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>INSTALLATION
Check the deceleration sensor for any inclination, bracket deformation or installation clearance.
The deceleration sensor is installed correctly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>INSTALLATION
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| G Sensor | Converted output voltage of G sensor | Min.: 0 V
Max.: 79.998 V |
·
2.31 to 2.69 V: Vehicle on level ground ·
1.88 to 2.5 V: Decelerating ·
2.5 to 3.11 V: Accelerating ·
Stuck at 1.87 V: G sensor malfunction ·
Stuck at 1.87 V: Communication malfunction |
- |
| Tester Display |
|---|
| G Sensor |
| Result | Proceed to |
|---|---|
| Data List value is normal | A |
| Data List value is not normal (w/ VSC) | B |
| Data List value is not normal (w/o VSC) | C |
A
B
C
Replace the ECM.
Click hereEngine / Hybrid System>2NR-FE ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Replace the airbag ECU assembly (yaw rate and acceleration sensor).
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>COMPONENTS
| Proceed to |
|---|
| NEXT |
NEXT
Replace the deceleration sensor.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>DECELERATION SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT