If code verification cannot be performed in the vehicle interior, there may be problems with the communication between the vehicle (indoor electrical key antenna assembly (center pillar RH), (center pillar LH) or (rear floor)) and electrical key transmitter sub-assembly, or the certification ECU (smart key ECU assembly) may be malfunctioning. When the electrical key transmitter sub-assembly is brought into the vehicle, verification of the key ID code transmitted from the electrical key transmitter sub-assembly and the key ID code stored in the certification ECU (smart key ECU assembly) is performed. If verification cannot be performed or the codes do not match, the engine switch cannot be turned on (IG) and the engine cannot be started.
When a door is unlocked and the electrical key transmitter sub-assembly is brought into the vehicle, the certification ECU (smart key ECU assembly) activates the indoor electrical key antenna assembly which transmits radio waves to detect the electrical key transmitter sub-assembly. If the electrical key transmitter sub-assembly recognizes that it is in the detection area, it responds with the key ID code. This information is received by the indoor electrical key antenna assembly and then sent to the certification ECU (smart key ECU assembly).
The smart entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Entry Function) precaution.
After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".
The indoor electrical key antenna assemblies have an antenna coil between each two CLG terminals.
The door control receiver is also related to interior verification.
Get into the vehicle while carrying a different, previously-registered electrical key transmitter sub-assembly.
Move the shift lever to P.*1
Depress the brake pedal*1 or clutch pedal*2.
Confirm that the smart warning light in the combination meter assembly illuminates in green, and then press the engine switch and check that the engine starts.
*1: for Automatic Transaxle and CVT
*2: for Manual Transaxle
| Result | Proceed to |
|---|---|
| Engine does not start | A |
| Engine starts normally | B |
A
B
Check that the wireless door lock functions operate normally.
Wireless door lock functions operate normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Engine Switch |
| *2 | Electrical Key Transmitter Sub-assembly |
Remove the transmitter battery of the electrical key transmitter sub-assembly.
Click hereVehicle Interior>DOOR LOCK>TRANSMITTER BATTERY(w/ Smart Entry and Start System)>REPLACEMENT
With the brake pedal*1 or clutch pedal*2 depressed, face the logo side of the electrical key transmitter sub-assembly towards the engine switch, hold the transmitter near the engine switch and then press the engine switch.
*1: for Automatic Transaxle and CVT
*2: for Manual Transaxle
When operating the engine switch, check whether the engine starts.
When the electrical key transmitter sub-assembly cannot be verified even though it is inside the detection area, the engine start check can be performed by removing the transmitter battery from the electrical key transmitter sub-assembly and holding the electrical key transmitter sub-assembly near the engine switch.
If the engine cannot be started when performing this inspection, the certification ECU (smart key ECU assembly), steering lock ECU (steering lock actuator assembly) may be malfunctioning.
Engine starts.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Install the transmitter battery to the electrical key transmitter sub-assembly.
Click hereVehicle Interior>DOOR LOCK>TRANSMITTER BATTERY(w/ Smart Entry and Start System)>REPLACEMENT
Bring the electrical key transmitter sub-assembly near the No. 1 indoor electrical key antenna assembly (center pillar RH) and perform a smart entry and start system check.
Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the No. 1 indoor electrical key antenna assembly (center pillar RH).
Bring the electrical key transmitter sub-assembly near the No. 1 indoor electrical key antenna assembly (center pillar LH) and perform a smart entry and start system check.
Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the No. 1 indoor electrical key antenna assembly (center pillar LH).
Bring the electrical key transmitter sub-assembly near the No. 2 indoor electrical key antenna assembly (rear floor) and perform a smart entry and start system check.
Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the No. 2 indoor electrical key antenna assembly (rear floor).
As the effect of wave interference decreases by moving the electrical key transmitter sub-assembly close to each indoor electrical key antenna assembly, it may be possible to check whether wave interference is the cause of the problem.
If the problem only occurs in specific places or at specific times, wave interference may be the cause of the problem. Also, the vehicle may be have the effects of wave interference with the parts installed by the dealer. As a result, when parts have been installed by the dealer, it may be necessary to remove those parts before inspecting the vehicle.
There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.
If a tool for checking electric waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.
| Result | Proceed to |
|---|---|
| System cannot be operated | A |
| System can be operated | B |
A
B
Clear the DTCs.
Recheck for DTCs.
DTC B27A1, B27A2 or B27A9 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the following antennas in key diagnostic mode.
Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.
If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.
for Sedan
| *a | Inspection Point |
Check the No. 1 indoor electrical key antenna assembly (center pillar RH) and No. 1 indoor electrical key antenna assembly (center pillar LH).
When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless door lock buzzer sounds.
| Tester Display |
|---|
| Communication Check(Key Diag Mode) |
| *a | Inspection Point |
Check the No. 2 indoor electrical key antenna assembly (rear floor).
When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless door lock buzzer sounds.
| Tester Display |
|---|
| Communication Check(Key Diag Mode) |
for Hatchback
| *a | Inspection Point |
Check the No. 1 indoor electrical key antenna assembly (center pillar RH) and No. 1 indoor electrical key antenna assembly (center pillar LH).
When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless door lock buzzer sounds.
| Tester Display |
|---|
| Communication Check(Key Diag Mode) |
| *a | Inspection Point |
Check the No. 2 indoor electrical key antenna assembly (rear floor).
When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless door lock buzzer sounds.
| Tester Display |
|---|
| Communication Check(Key Diag Mode) |
If the buzzer sounds, it can be determined that the vehicle interior transmitters are operating normally.
It is possible to check which indoor electrical key antenna assembly (center pillar RH, center pillar LH or rear floor) is operating by the sounding of the buzzer.
If the buzzer does not sound for any indoor electrical key antenna assemblies, the certification ECU (smart key ECU assembly) circuit may be malfunctioning.
Wireless door lock buzzer sounds.
| Result | Proceed to |
|---|---|
| Center pillar RH/LH operation check fails | A |
| Rear floor operation check fails | B |
| All operation checks are normal | C |
| All operation checks fail | D |
A
B
C
D
Check the operation of the entry lock/unlock function.
Entry lock/unlock operate normally.
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG (for LHD) | C |
| NG (for RHD) | D |
A
B
C
D
Disconnect the F44 certification ECU (smart key ECU assembly) connector.
Disconnect the F48 No. 1 indoor electrical key antenna assembly (center pillar RH) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F44-6 (CLG2) - F48-1 (ANTE2) | Always | Below 1 Ω |
| F44-23 (CG2B) - F48-3 (CLGB) | Always | Below 1 Ω |
| F44-6 (CLG2) or F48-1 (ANTE2) - Body ground | Always | 10 kΩ or higher |
| F44-23 (CG2B) or F48-3 (CLGB) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the F44 certification ECU (smart key ECU assembly) connector.
Connect the F48 No. 1 indoor electrical key antenna assembly (center pillar RH) connector.
Get into the vehicle while carrying the electrical key transmitter sub-assembly.
Move the shift lever to P.*1
Depress the brake pedal*1 or clutch pedal*2.
*1: for Automatic Transaxle and CVT
*2: for Manual Transaxle
Confirm that the smart warning light in the combination meter assembly illuminates in green, and then press the engine switch and check that the engine starts.
| Result | Proceed to |
|---|---|
| Engine does not start | A |
| Engine starts normally | B |
A
B
Connect the F44 certification ECU (smart key ECU assembly) connector.
Connect the F48 No. 1 indoor electrical key antenna assembly (center pillar RH) connector.
Using an oscilloscope, check the waveform.
| *a | Component with harness connected
(No. 1 Indoor Electrical Key Antenna Assembly (Center Pillar RH)) |
*b | Waveform 1 |
| *c | Within approximately 30 seconds from when the door is closed | *d | After approximately 30 seconds from when the door is closed |
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| F48-1 (ANTE2) - F48-3 (CLGB) | Procedure:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly not inside vehicle 3.
Door is open 4.
Door is closed 5.
Within 30 seconds |
2 V/DIV., 500 ms./DIV. | Pulse generation
(See waveform 1) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F44 certification ECU (smart key ECU assembly) connector.
Disconnect the F49 No. 1 indoor electrical key antenna assembly (center pillar LH) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F44-6 (CLG2) - F49-1 (ANTE2) | Always | Below 1 Ω |
| F44-23 (CG2B) - F49-3 (CLGB) | Always | Below 1 Ω |
| F44-6 (CLG2) or F49-1 (ANTE2) - Body ground | Always | 10 kΩ or higher |
| F44-23 (CG2B) or F49-3 (CLGB) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the F44 certification ECU (smart key ECU assembly) connector.
Connect the F49 No. 1 indoor electrical key antenna assembly (center pillar LH) connector.
Get into the vehicle while carrying the electrical key transmitter sub-assembly.
Move the shift lever to P.*1
Depress the brake pedal*1 or clutch pedal*2.
*1: for Automatic Transaxle and CVT
*2: for Manual Transaxle
Confirm that the smart warning light in the combination meter assembly illuminates in green, and then press the engine switch and check that the engine starts.
| Result | Proceed to |
|---|---|
| Engine does not start | A |
| Engine starts normally | B |
A
B
Connect the F44 certification ECU (smart key ECU assembly) connector.
Connect the F49 No. 1 indoor electrical key antenna assembly (center pillar LH) connector.
Using an oscilloscope, check the waveform.
| *a | Component with harness connected
(No. 1 Indoor Electrical Key Antenna Assembly (Center Pillar LH)) |
*b | Waveform 1 |
| *c | Within approximately 30 seconds from when the door is closed | *d | After approximately 30 seconds from when the door is closed |
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| F49-1 (ANTE2) - F49-3 (CLGB) | Procedure:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly not inside vehicle 3.
Door is open 4.
Door is closed 5.
Within 30 seconds |
2 V/DIV., 500 ms./DIV. | Pulse generation
(See waveform 1) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F44 certification ECU (smart key ECU assembly) connector.
Disconnect the F49 No. 1 indoor electrical key antenna assembly (center pillar LH) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F44-31 (CLG1) - F49-1 (ANTE1) | Always | Below 1 Ω |
| F44-30 (CG1B) - F49-3 (CLGB) | Always | Below 1 Ω |
| F44-31 (CLG1) or F49-1 (ANTE1) - Body ground | Always | 10 kΩ or higher |
| F44-30 (CG1B) or F49-3 (CLGB) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the F44 certification ECU (smart key ECU assembly) connector.
Connect the F49 No. 1 indoor electrical key antenna assembly (center pillar LH) connector.
Get into the vehicle while carrying the electrical key transmitter sub-assembly.
Move the shift lever to P.*1
Depress the brake pedal*1 or clutch pedal*2.
*1: for Automatic Transaxle and CVT
*2: for Manual Transaxle
Confirm that the smart warning light in the combination meter assembly illuminates in green, and then press the engine switch and check that the engine starts.
| Result | Proceed to |
|---|---|
| Engine does not start | A |
| Engine starts normally | B |
A
B
Connect the F44 certification ECU (smart key ECU assembly) connector.
Connect the F49 No. 1 indoor electrical key antenna assembly (center pillar LH) connector.
Using an oscilloscope, check the waveform.
| *a | Component with harness connected
(No. 1 Indoor Electrical Key Antenna Assembly (Center Pillar LH)) |
*b | Waveform 1 |
| *c | Trigger switch ON | - | - |
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| F49-1 (ANTE1) - F49-3 (CLGB) | Procedure:
1.
Engine switch off 2.
All doors closed |
2 V/DIV., 500 ms./DIV. | Not pulse generation |
| Procedure:
1.
Engine switch off 2.
All doors closed 3.
Press the trigger switch on the front door outside handle assembly (for driver door) |
2 V/DIV., 500 ms./DIV. | Pulse generation
(See waveform 1) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F44 certification ECU (smart key ECU assembly) connector.
Disconnect the F48 No. 1 indoor electrical key antenna assembly (center pillar RH) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F44-31 (CLG1) - F48-1 (ANTE1) | Always | Below 1 Ω |
| F44-30 (CG1B) - F48-3 (CLGB) | Always | Below 1 Ω |
| F44-31 (CLG1) or F48-1 (ANTE1) - Body ground | Always | 10 kΩ or higher |
| F44-30 (CG1B) or F48-3 (CLGB) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the F44 certification ECU (smart key ECU assembly) connector.
Connect the F48 No. 1 indoor electrical key antenna assembly (center pillar RH) connector.
Get into the vehicle while carrying the electrical key transmitter sub-assembly.
Move the shift lever to P.*1
Depress the brake pedal*1 or clutch pedal*2.
*1: for Automatic Transaxle and CVT
*2: for Manual Transaxle
Confirm that the smart warning light in the combination meter assembly illuminates in green, and then press the engine switch and check that the engine starts.
| Result | Proceed to |
|---|---|
| Engine does not start | A |
| Engine starts normally | B |
A
B
Connect the F44 certification ECU (smart key ECU assembly) connector.
Connect the F48 No. 1 indoor electrical key antenna assembly (center pillar RH) connector.
Using an oscilloscope, check the waveform.
| *a | Component with harness connected
(No. 1 Indoor Electrical Key Antenna Assembly (Center Pillar RH)) |
*b | Waveform 1 |
| *c | Trigger switch ON | - | - |
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| F48-1 (ANTE1) - F48-3 (CLGB) | Procedure:
1.
Engine switch off 2.
All doors closed |
2 V/DIV., 500 ms./DIV. | Not pulse generation |
| Procedure:
1.
Engine switch off 2.
All doors closed 3.
Press the trigger switch on the front door outside handle assembly (for driver door) |
2 V/DIV., 500 ms./DIV. | Pulse generation
(See waveform 1) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F44 certification ECU (smart key ECU assembly) connector.
Disconnect the F50 No. 2 indoor electrical key antenna assembly (rear floor) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F44-26 (CLG6) - F50-1 (ANTE6) | Always | Below 1 Ω |
| F44-27 (CG6B) - F50-3 (CLGB) | Always | Below 1 Ω |
| F44-26 (CLG6) or F50-1 (ANTE6) - Body ground | Always | 10 kΩ or higher |
| F44-27 (CG6B) or F50-3 (CLGB) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the F44 certification ECU (smart key ECU assembly) connector.
Connect the F50 No. 2 indoor electrical key antenna assembly (rear floor) connector.
Get into the vehicle while carrying the electrical key transmitter assembly.
Move the shift lever to P.*1
Depress the brake pedal*1 or clutch pedal*2.
*1: for Automatic Transaxle and CVT
*2: for Manual Transaxle
Confirm that the smart warning light in the combination meter assembly illuminates in green, and then press the engine switch and check that the engine starts.
| Result | Proceed to |
|---|---|
| Engine does not start | A |
| Engine starts normally | B |
A
B
Connect the F44 certification ECU (smart key ECU assembly) connector.
Connect the F50 No. 2 indoor electrical key antenna assembly (rear floor) connector.
Using an oscilloscope, check the waveform.
| *a | Component with harness connected
(No. 2 Indoor Electrical Key Antenna Assembly (Rear Floor) |
*b | Waveform 1 |
| *c | Within approximately 30 seconds from when the door is closed | *d | After approximately 30 seconds from when the door is closed |
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| F50-1 (ANTE6) - F50-3 (CLGB) | Procedure:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly not inside vehicle 3.
Door is open 4.
Door is closed 5.
Within 30 seconds |
2 V/DIV., 500 ms./DIV. | Pulse generation
(See waveform 1) |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ELECTRICAL KEY OSCILLATOR(for Rear Floor)>REMOVAL
NG
Get into the vehicle while carrying the electrical key transmitter sub-assembly.
Move the shift lever to P.*1
Depress the brake pedal*1 or clutch pedal*2.
*1: for Automatic Transaxle and CVT
*2: for Manual Transaxle
Confirm that the smart warning light in the combination meter assembly illuminates in green, and then press the engine switch and check that the engine starts.
Engine starts normally.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG