Home › Engine / Hybrid System › 1NR-FE ENGINE CONTROL › SFI SYSTEM › 2016.04–2017.10
RM30M0E _51 Engine / Hybrid System _053310 1NR-FE ENGINE CONTROL _0258661 SFI SYSTEM C

1NR-FE ENGINE CONTROL  SFI SYSTEM  C147A  Atmospheric Pressure Sensor Circuit Low  C147B  Atmospheric Pressure Sensor Circuit High  


DESCRIPTION

The atmospheric pressure sensor detects the atmospheric pressure. By detecting the atmospheric pressure, it is possible to calculate brake negative pressure values reflecting the effects of air pressure fluctuations caused by altitude changes.

When the ECM determines that there is a malfunction in the input signal from the atmospheric pressure sensor, it stores DTC C147A,C147B.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
C147A Atmospheric Pressure Sensor Circuit Low All of the following conditions are met (1 trip detection logic):

(a) After 2 seconds or more elapse after turn the ignition switch to ON.

(b) After 2 seconds or more elapse after starting the engine.

(c) The atmospheric pressure sensor input voltage is less than 0.5 V for 1.2 seconds or more.


·

Wire harness or connector

·

Atmospheric pressure sensor

·

ECM


Does not come on DTC Stored
C147B Atmospheric Pressure Sensor Circuit High All of the following conditions are met (1 trip detection logic):

(a) After 2 seconds or more elapse after turn the ignition switch to ON.

(b) After 2 seconds or more elapse after starting the engine.

(c) The atmospheric pressure sensor input voltage is more than 4.5 V for 1.2 seconds or more (1 trip detection logic).


·

Wire harness or connector

·

Atmospheric pressure sensor

·

ECM


Does not come on DTC Stored

HINT:

When either of the DTCs have been stored, the ECM enters fail-safe mode. During fail-safe mode operation, to prevent the brake vacuum pressure from decreasing when driving at high altitudes, the air conditioner turns off more frequently. Fail-safe mode operation continues until the ECM condition returns to normal (w/ Air Conditioning System).


CONFIRMATION DRIVING PATTERN

HINT:

DTCs for the SFI system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.


1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Start the engine and allow it to idle for 15 seconds or more.

6.

Turn the ignition switch off.

7.

Turn the ignition switch to ON.

8.

Turn the GTS on.

9.

Enter the following menus: Powertrain / Engine and ECT / Data List / Atmosphere Pressure.

10.

Read the values displayed on the GTS.

Standard:

Approximately the same as ambient atmospheric pressure.


HINT:
·

Standard atmospheric pressure is 101 kPa(abs) [758 mmHg(abs)].

·

For every 100 m (328 ft.) increase in altitude, pressure drops by 1 kPa (7.5 mmHg). This varies by weather.



11.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

13.

Input the DTC: C147A or C147B.

14.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A380447E08
1.448,0.917 1.76,1.115 0.313,0.198 10 false VC 1.448,1.594 1.76,1.792 0.313,0.198 10 false PB 1.469,2.385 1.781,2.583 0.313,0.198 10 false E2 1.781,0.802 2.094,1 0.313,0.198 10 false 3 1.781,1.5 2.094,1.698 0.313,0.198 10 false 2 1.781,2.271 2.094,2.469 0.313,0.198 10 false 1 0.375,2.74 0.865,3 0.49,0.26 10 false F117 0.375,2.906 2.25,3.354 1.875,0.448 10 false Atmospheric Pressure Sensor 4.385,0.802 4.698,1 0.313,0.198 10 false 33 4.385,1.49 4.698,1.688 0.313,0.198 10 false 25 4.385,2.271 4.698,2.469 0.313,0.198 10 false 34 4.688,0.802 5.333,1.021 0.646,0.219 10 false VHAC 4.688,1.49 5,1.688 0.313,0.198 10 false HAC 4.688,2.271 5.375,2.51 0.688,0.24 10 false EHAC 5.24,2.99 5.885,3.208 0.646,0.219 10 false F130 5.229,3.156 5.875,3.375 0.646,0.219 10 false ECM

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT ATMOSPHERIC PRESSURE SENSOR
a.

Inspect the atmospheric pressure sensor.

Click hereEngine / Hybrid System>1NR-FE ENGINE CONTROL>ATMOSPHERIC PRESSURE SENSOR>ON-VEHICLE INSPECTION

Result:
Proceed to
OK
NG




OK

NG

2.CHECK ECM TERMINAL VOLTAGE (VHAC TERMINAL VOLTAGE)
2.CHECK ECM TERMINAL VOLTAGE (VHAC TERMINAL VOLTAGE)
A342760C01
2.01,0.5 2.51,0.75 0.5,0.25 1.583,2.667 2.083,2.917 0.5,0.25 1.583,2 2.104,1.188 true 2.583,2 2.146,1.188 true 1.156,4.156 1.677,3.344 true 2.177,4.156 1.74,3.344 true 0.104,0.135 0.417,0.333 0.313,0.198 10 false *a 0.333,0.417 0.708,0.656 0.375,0.24 12 false *A 0.354,2.51 0.729,2.75 0.375,0.24 12 false *B 2.083,0.531 2.698,0.729 0.615,0.198 10 false F130 1.646,2.698 2.26,2.896 0.615,0.198 10 false F130 1.094,1.875 1.708,2.073 0.615,0.198 10 false EHAC 2.635,1.896 3.25,2.094 0.615,0.198 10 false VHAC 0.667,4.052 1.281,4.25 0.615,0.198 10 false EHAC 2.26,4.063 2.875,4.26 0.615,0.198 10 false VHAC
*A for CVT
*B for Manual Transaxle
*a Component with harness connected
(ECM)


a.

Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F130-33 (VHAC) - F130-34 (EHAC) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (ECM - ATMOSPHERIC PRESSURE SENSOR)

NG

3.CHECK HARNESS AND CONNECTOR (ECM - ATMOSPHERIC PRESSURE SENSOR)
a.

Disconnect the F130 ECM connector.


b.

Disconnect the F117 atmospheric pressure sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F130-33 (VHAC) - F117-3 (VC) Always Below 1 Ω
F130-25 (HAC) - F117-2 (PB) Always Below 1 Ω
F130-34 (EHAC) - F117-1 (E2) Always Below 1 Ω
F130-33 (VHAC) or F117-3 (VC) - Body ground and other terminals Always 10 kΩ or higher
F130-25 (HAC) or F117-2 (PB) - Body ground and other terminals Always 10 kΩ or higher
F130-34 (EHAC) or F117-1 (E2) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.REPLACE ATMOSPHERIC PRESSURE SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE ATMOSPHERIC PRESSURE SENSOR
a.

Result:
Proceed to
NEXT



NEXT

5.CLEAR DTC
5.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

e.

Clear the DTC.

Powertrain > Engine and ECT > Clear DTCs
50002 234

Result:
Proceed to
NEXT



NEXT

6.CHECK DTC OUTPUT
6.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Warm up the engine.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Atmosphere Pressure.

Powertrain > Engine and ECT > Data List
Tester Display
Atmosphere Pressure
50003 234 7

f.

Read the values displayed on the GTS.

OK:

Approximately the same as ambient atmospheric pressure.


HINT:
·

Standard atmospheric pressure is 101 kPa(abs) [758 mmHg(abs)].

·

For every 100 m (328 ft.) increase in altitude, pressure drops by 1 kPa (7.5 mmHg). This varies by weather.




g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

h.

Check that no DTCs are output.

Result:
Result Proceed to
DTCs are not output A
DTC C147A or C147B is output B




A

END

B