Home › Drivetrain › K411 CVT › TORQUE CONVERTER AND DRIVE PLATE › from 2016.04
RM30M0E _52 Drivetrain _052750 K411 CVT _0259916 TORQUE CONVERTER AND DRIVE PLATE A

K411 CVT  TORQUE CONVERTER AND DRIVE PLATE  INSPECTION  


PROCEDURE

Hide 1.INSPECT TORQUE CONVERTER ASSEMBLY

a.

Inspect the one-way clutch.

i.
C195059C08
0,0 3.427,0 false
V100135

Difficult
V100136

Smooth


Press on the spline of the stator with a finger and rotate the spline. Check that the spline rotates smoothly when turned clockwise and rotates with difficulty when turned counterclockwise.

If necessary, clean the torque converter assembly and recheck the one-way clutch. Replace the torque converter assembly if the one-way clutch still fails the inspection.



b.
C197457C08
0.083,0 0.5,0.385 0.417,0.385 10 *a 1.677,3.26 1.865,3.417 0.188,0.156 10 *b
*a Sample showing maximum allowable amount of powder in fluid
*b Full Scale


Inspect the torque converter assembly.

If any of the following problems are present, replace the torque converter assembly.

Malfunction:
·

A metallic sound is emitted from the torque converter assembly during the stall test or when the shift lever is moved to N.

·

The one-way clutch turns smoothly or locks in both directions.

·

The amount of powder in the fluid is more than the sample shown in the illustration (refer to the sample).


HINT:

The sample shows approximately 0.025 liters (0.026 US qts, 0.022 Imp. qts) of fluid in a Petri dish, which has been taken from the removed torque converter assembly.



c.

Replace the fluid in the torque converter assembly.

HINT:

If the fluid is discolored or has a foul odor, stir the fluid in the torque converter assembly and drain it before replacing the fluid.



d.
C155807

Clean and check the transmission oil cooler.

HINT:
·

If the torque converter assembly is inspected or the fluid is replaced, it is necessary to clean the transmission oil cooler.

·

Apply compressed air of 196 kPa (2.0 kgf/cm2, 28 psi) into the hole of transmission oil cooler.

·

If a large amount of powder is found in the fluid, add new fluid using a bucket pump and clean the transmission oil cooler again.

·

If the fluid is cloudy, inspect the transmission oil cooler.




e.
C282855C01
2.458,1.667 2.927,1.667 true 0.375,0.198 0.688,0.396 0.313,0.198 10 false *a 1.74,0.198 2.052,0.396 0.313,0.198 10 false *b 2.969,1.573 3.281,1.771 0.313,0.198 10 false *c
*a Correct
*b Incorrect
*c Bottom is damaged


Prevent deformation of the torque converter assembly and damage to the oil pump gear.

NOTICE:

Make sure that all of the bolts are the same length and that the specified bolts are used.


HINT:

If there is any damage to the tip of a bolt for the torque converter assembly or to the bottom of a bolt hole, replace the bolt and torque converter assembly.



Hide 2.INSPECT DRIVE PLATE

a.

Check the drive plate for damage.


b.
C288105C01
1.406,1.063 1.531,1.25 0.125,0.188 10 false 1 1.802,0.375 1.927,0.563 0.125,0.188 10 false 2 2.552,0.531 2.677,0.719 0.125,0.188 10 false 3 2.979,1.229 3.104,1.417 0.125,0.188 10 false 4 2.771,1.917 2.896,2.104 0.125,0.188 10 false 5 1.948,1.938 2.073,2.125 0.125,0.188 10 false 6
V100144

Measurement Point


Set up a dial indicator and measure the runout at the 6 areas on the drive plate surface that contact the torque converter assembly.

Maximum runout:

0.30 mm (0.0118 in.)


If the runout is more than the maximum or the drive plate is damaged, replace the drive plate.

Click hereEngine / Hybrid System>1NR-FE ENGINE MECHANICAL>REAR CRANKSHAFT OIL SEAL>REMOVAL