Home › Drivetrain › K411 CVT › PARK / NEUTRAL POSITION SWITCH › 2016.04–2017.10
RM30M0E _52 Drivetrain _052750 K411 CVT _0259922 PARK / NEUTRAL POSITION SWITCH A

K411 CVT  PARK / NEUTRAL POSITION SWITCH  INSTALLATION  


PROCEDURE

Hide 84540 1.INSTALL PARK/NEUTRAL POSITION SWITCH

a.

Temporarily install the park/neutral position switch to the continuously variable transaxle assembly with the 2 bolts.


b.
C288558

Install a new lock plate and lock nut to the park/neutral position switch.

Torque:
6.9 N*m (70 kgf*cm, 61 in.*lbf)


c.
C288559C01
2.885,0.875 3.083,1.063 0.198,0.188 10 true *a 2.646,0.396 2.823,0.573 0.177,0.177 10 true *b
*a P Position
*b N Position


Temporarily install the transmission control shaft lever to the continuously variable transaxle assembly.


d.

Rotate the transmission control shaft lever clockwise until it stops, and then from that position rotate it counterclockwise by 2 notches to set it to the N position.


e.

Remove the transmission control shaft lever from the continuously variable transaxle assembly.


f.
C288560C01
2.5,1.188 1.99,0.875 true 2.344,1.417 1.781,1 true 2.521,1.104 2.708,1.292 0.188,0.188 10 true *a 2.375,1.354 2.552,1.542 0.177,0.188 10 true *b
*a Neutral Basic Line
*b Protrusion


Rotate the park/neutral position switch clockwise or counterclockwise to align the neutral basic line with the protrusion as shown in the illustration.


g.

Hold the park/neutral position switch in this position and tighten the 2 bolts.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


h.
C288758

Using a screwdriver, secure the lock nut with the lock plate.


i.

Install the transmission control shaft lever to the continuously variable transaxle assembly with the washer and nut.

Torque:
12.3 N*m (125 kgf*cm, 9 ft.*lbf)


j.

Connect the park/neutral position switch connector.


Hide 33820B 2.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

NOTICE:

To prevent damage to the transmission control cable assembly and transmission floor shift assembly, connect the continuously variable transaxle assembly side of the transmission control cable assembly before connecting the transmission floor shift assembly side.


a.
C288559C01
2.885,0.875 3.083,1.063 0.198,0.188 10 true *a 2.646,0.396 2.823,0.573 0.177,0.177 10 true *b
*a P Position
*b N Position


Rotate the transmission control shaft lever clockwise until it stops, and then from that position rotate it counterclockwise by 2 notches to set it to the N position.


b.
C288554C01
0.948,0.458 1.458,0.458 true 0.781,0.354 0.938,0.552 0.156,0.198 10 true *a
*a Paint Mark


Install the transmission control cable assembly to the No. 1 transmission control cable bracket with a new clip.

NOTICE:

Make sure that the paint mark on the transmission control cable assembly is aligned with the slit in the No. 1 transmission control cable bracket before installing the clip.



c.

Connect the transmission control cable assembly to the transmission control shaft lever with the nut.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


d.
C286313

Confirm that the shift lever is in N, and then connect the end of the transmission control cable assembly to the transmission floor shift assembly.

NOTICE:
·

Securely install the end of the transmission control cable assembly to the transmission floor shift assembly.

·

Install the end of the transmission control cable assembly so that its adjustment lock section is on the driver side.




Hide 3.ADJUST SHIFT LEVER POSITION

Hide 17701 8.INSTALL AIR CLEANER CASE SUB-ASSEMBLY

Hide 17801 9.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 17880 11.INSTALL AIR CLEANER HOSE ASSEMBLY

Hide 12.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

Hide 84540 13.INSPECT PARK/NEUTRAL POSITION SWITCH

Hide 14.INSPECT SHIFT LEVER POSITION