Home › Engine / Hybrid System › 2NR-FE ENGINE MECHANICAL › CYLINDER BLOCK › from 2016.04
RM30M0E _51 Engine / Hybrid System _053933 2NR-FE ENGINE MECHANICAL _0262439 CYLINDER BLOCK A

2NR-FE ENGINE MECHANICAL  CYLINDER BLOCK  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repair" after replacing the piston with pin sub-assembly or piston ring set.

Click hereEngine / Hybrid System>2NR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


PROCEDURE

Hide 15708 1.INSTALL NO. 1 OIL NOZZLE SUB-ASSEMBLY

a.
A198045

Using a 5 mm socket hexagon wrench, install the 4 No. 1 oil nozzle sub-assemblies to the cylinder block sub-assembly with the 4 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 13101 2.INSTALL PISTON WITH PIN SUB-ASSEMBLY

NOTICE:

If the piston pin has been removed from the piston, replace the piston, piston pin and connecting rod with new ones.


a.

Gradually heat a new connecting rod to 80°C (176°F) or more.

CAUTION:

Make sure not to burn yourself.



b.
A313278C01
1.042,1.313 1.615,2.083 1.615,2.083 2.469,1.479 true 1.094,3.646 1.667,4.417 1.667,4.417 2.5,4.135 true 1.531,2.073 1.844,2.229 0.313,0.156 10 false *a 1.594,4.417 1.906,4.573 0.313,0.156 10 false *a
*a Front Mark


Coat a new piston pin and pin holes of a new piston with engine oil.


c.

Align the front mark of the piston with that of the connecting rod.


d.

Using SST, press in the piston pin.

A313280C01
0.833,0.833 0.583,0.833 false 0.823,1.333 0.573,1.333 false 0.583,2.031 0.417,2.031 false 2.938,0.552 2.688,0.552 false 3.969,1.229 3.552,1.229 true 2.76,1.458 3.083,1.75 true 2.979,2.042 2.729,2.042 false 4.729,1.219 4.479,1.219 false 4.583,0.75 4.167,0.75 false 6.083,1.604 6.083,2.167 true 6.333,1.542 6.333,2.104 true 6.771,1.448 6.521,1.448 false 5.844,1.302 5.469,1.865 5.469,1.865 5.844,1.625 true 4.604,0.635 4.917,0.792 0.313,0.156 10 false *1 3.375,1.125 3.688,1.281 0.313,0.156 10 false *2 4.75,1.115 5.063,1.271 0.313,0.156 10 false *3 0.302,0.74 0.781,0.938 0.479,0.198 10 false SST 3.094,1.646 3.406,1.802 0.313,0.156 10 false *a 5.313,1.792 5.625,1.948 0.313,0.156 10 false *b 5.385,0.469 6.708,0.885 1.323,0.417 10 false 1.4 to 2.7 mm (0.0551 to 0.1063 in.) 0.292,1.229 0.771,1.427 0.479,0.198 10 false SST 0.125,1.938 0.604,2.135 0.479,0.198 10 false SST 2.99,0.448 3.469,0.646 0.479,0.198 10 false SST 3.01,1.938 3.49,2.135 0.479,0.198 10 false SST 6.792,1.344 7.104,1.5 0.313,0.156 10 false *3 6.021,2.177 6.333,2.333 0.313,0.156 10 false *2 6.292,2.104 6.604,2.26 0.313,0.156 10 false *1
*1 Piston Pin *2 Connecting Rod
*3 Piston - -
*a Front Mark *b Contact
V100135

Rear Side - -


SST
09221-25026  (09221-00021, 09221-00030, 09221-00090, 09221-00100, 09221-00150)

NOTICE:
·

Press in the piston pin from the side of the piston with the front mark as shown in the illustration.

·

With the connecting rod fully inserted into the piston end, press in the piston pin until it is flush with the piston surface.




e.

Check the fitting condition between the piston and piston pin by trying to move the piston back and forth on the piston pin.

HINT:

Perform "Inspection After Repair" after replacing the piston.

Click hereEngine / Hybrid System>2NR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Hide 13011 3.INSTALL PISTON RING SET

a.
A313281C01
1.292,0.875 1.719,0.26 false 2.552,0.885 2.823,0.885 false 2.375,1.073 2.646,1.073 true 2.552,1.26 2.823,1.26 false 2.833,0.781 3.146,0.938 0.313,0.156 10 false *1 2.677,0.979 2.99,1.135 0.313,0.156 10 false *2 2.833,1.167 3.146,1.323 0.313,0.156 10 false *3 1.729,0.135 2.042,0.292 0.313,0.156 10 false *a
*1 Side Rail (Upper)
*2 Expander Spacer
*3 Side Rail (Lower)
*a Expander Spacer and Side Rail Groove


Install the expander spacer and 2 side rails by hand, as shown in the illustration.


b.
A313282C01
0.406,2.74 0.719,2.896 0.313,0.156 10 false *1 0.396,4 0.708,4.156 0.313,0.156 10 false *2
*1 No. 1 Compression Ring
*2 No. 2 Compression Ring
V100135

Piston Top


Using a piston ring expander, install the No. 1 compression ring and No. 2 compression ring as shown in the illustration.

NOTICE:

Install the No. 2 compression ring with the code mark (T2) facing upward.



c.
A313283C01
0.708,1 1.021,1.156 0.313,0.156 10 false *1 2.563,0.99 2.875,1.146 0.313,0.156 10 false *2 1.656,0.073 1.969,0.229 0.313,0.156 10 false *3 1.646,1.948 1.958,2.104 0.313,0.156 10 false *4
*1 No. 1 Compression Ring and Expander Spacer
*2 No. 2 Compression Ring
*3 Side Rail (Upper)
*4 Side Rail (Lower)
V100135

Engine Front


Position the piston rings so that the ring ends are as shown in the illustration.

HINT:

Perform "Inspection After Repair" after replacing the piston ring set.

Click hereEngine / Hybrid System>2NR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Hide 11711 4.INSTALL CRANKSHAFT BEARING

a.

Install the 5 crankshaft bearings (upper) to the cylinder block sub-assembly.

A313284C01
4.667,2.885 4.979,3.042 0.313,0.156 10 false *a 5.406,2.885 5.719,3.042 0.313,0.156 10 false *b
*a Correct *b Incorrect
V100135

Engine Front - -


NOTICE:
·

Align the oil holes in the crankshaft bearing with the oil holes in the cylinder block sub-assembly.

·

Do not apply engine oil to the crankshaft bearings or the contact surfaces.




b.

Install the crankshaft bearing (lower).

i.

Install the 5 crankshaft bearings (lower) to the 5 crankshaft bearing caps.


ii.
A198656E03
1.574,2.128 1.703,2.302 0.128,0.175 10 A 1.574,2.712 1.703,2.887 0.128,0.175 10 B

Using a vernier caliper, measure the distance between the crankshaft bearing cap edge and crankshaft bearing (lower) edge.

Dimension (A - B):

0.8 mm (0.0315 in.) or less


NOTICE:

Do not apply engine oil to the crankshaft bearings or the contact surfaces.




Hide 11791 5.INSTALL UPPER CRANKSHAFT THRUST WASHER

a.
A198042C03
1.344,1.083 1.219,1.427 1.219,1.427 1.5,1.156 true 1.094,1.448 1.646,1.813 0.552,0.365 10 *a
*a Oil Grooves


Install the 2 upper crankshaft thrust washers under the No. 3 journal of the cylinder block sub-assembly with the oil grooves facing outward.


b.

Apply engine oil to the 2 upper crankshaft thrust washers.


Hide 13411 6.INSTALL CRANKSHAFT

a.

Apply engine oil to the crankshaft bearings (upper) and install the crankshaft on the cylinder block sub-assembly.


b.

Apply engine oil to the crankshaft bearings (lower).


c.
A198657C04
0.594,2.948 1.125,3.302 0.531,0.354 10 *a
*a Number Mark
V100135

Front


Examine the number marks and install the crankshaft bearing caps on the cylinder block sub-assembly.


d.

Apply a light coat of engine oil to the threads and under the crankshaft bearing cap set bolts.


e.
A313285

Temporarily install the 10 crankshaft bearing cap set bolts.


f.

Step 1

i.
A313286E01
0.635,0.146 0.792,0.344 0.156,0.198 10 true 7 1.177,0.135 1.354,0.292 0.177,0.156 10 true 3 1.688,0.125 1.865,0.271 0.177,0.146 10 true 1 2.167,0.125 2.354,0.271 0.188,0.146 10 true 5 2.667,0.156 2.823,0.354 0.156,0.198 10 true 9 0.677,1.479 0.833,1.677 0.156,0.198 10 true 8 1.167,1.469 1.323,1.667 0.156,0.198 10 true 4 1.677,1.438 1.833,1.635 0.156,0.198 10 true 2 2.708,1.469 2.906,1.635 0.198,0.167 10 true 10 2.188,1.458 2.344,1.656 0.156,0.198 10 true 6

Uniformly tighten the 10 crankshaft bearing cap set bolts in the sequence shown in the illustration.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)



g.

Step 2

i.
A314372C01
2.208,0.604 2.708,0.24 true 2.792,0.135 3.115,0.406 0.323,0.271 10 false *a 1.281,0.344 1.594,0.615 0.313,0.271 10 false 90°
*a Paint Mark
V100135

Engine Front


Mark the front of the crankshaft bearing cap set bolts with paint.


ii.

Further tighten the crankshaft bearing cap set bolts an additional 90° in the sequence shown in the previous illustration.



h.

Check that the paint mark is now at a 90° angle to the front.


i.

Check that the crankshaft turns smoothly.


j.

Inspect the crankshaft thrust clearance.

Click hereEngine / Hybrid System>2NR-FE ENGINE MECHANICAL>CYLINDER BLOCK>INSPECTION


Hide 13041 7.INSTALL CONNECTING ROD BEARING

a.

Install the connecting rod bearing to the connecting rod and connecting rod cap.


b.
A305668E01
1.104,2.156 1.26,2.354 0.156,0.198 10 false A 2.198,2.156 2.354,2.354 0.156,0.198 10 false B

Using a vernier caliper, measure the distance between the connecting rod edge and connecting rod bearing (upper) edge.

Dimension (A - B):

0.5 mm (0.0197 in.)


NOTICE:

Do not apply engine oil to the connecting rod bearings or the contact surfaces.



c.
A305669E01
1.115,2.167 1.271,2.365 0.156,0.198 10 false A 2.208,2.156 2.365,2.354 0.156,0.198 10 false B

Using a vernier caliper, measure the distance between the connecting rod cap edge and connecting rod bearing (lower) edge.

Dimension (A - B):

0.5 mm (0.0197 in.)


NOTICE:

Do not apply engine oil to the connecting rod bearings or the connecting contact surfaces.



Hide 8.INSTALL PISTON WITH PIN SUB-ASSEMBLY WITH CONNECTING ROD SUB-ASSEMBLY

a.

Apply engine oil to the cylinder walls, the pistons, and surfaces of the connecting rod bearings.


b.
A313283C02
0.698,1 1.01,1.156 0.313,0.156 10 false *1 2.583,0.99 2.896,1.146 0.313,0.156 10 false *2 1.656,0.073 1.969,0.229 0.313,0.156 10 false *3 1.646,1.938 1.958,2.094 0.313,0.156 10 false *4
*1 No. 1 Compression Ring and Expander Spacer
*2 No. 2 Compression Ring
*3 Side Rail (Upper)
*4 Side Rail (Lower)
V100135

Engine Front


Position the piston rings so that the ring ends are as shown in the illustration.

NOTICE:

Do not align the ring ends.



c.
A313287C01
2.688,2.604 1.646,4.115 1.646,4.115 2.656,4.042 true 1.469,4.031 1.781,4.188 0.313,0.156 10 false *a
*a Front Mark


Using a piston ring compressor, push the correctly numbered piston with pin sub-assembly with connecting rod into the cylinder block sub-assembly with the front mark of the piston facing forward.

NOTICE:
·

When inserting the piston with connecting rod, do not allow it to make contact with the No. 1 oil nozzle sub-assembly.

·

Match the numbered connecting rod cap with the connecting rod.




d.
A313269C01
1.052,0.375 0.635,0.177 true 0.458,0.063 0.771,0.219 0.313,0.156 10 false *a
*a Front Mark


Check that the front mark of the connecting rod cap is facing in the correct direction.


e.

Apply a light coat of engine oil to the threads and under the heads of the connecting rod bolts.


f.

Temporarily install the connecting rod bolts.


g.

Step 1

i.
A313289E01
1.646,0.938 2.219,0.438 false 2.26,0.333 2.719,0.531 0.458,0.198 10 false SST

Using SST, alternately tighten the 2 connecting rod bolts of the connecting rod cap.

SST
09205-16010  

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)



h.

Step 2

i.
A314373C01
2.063,0.75 2.49,0.323 true 2.573,0.219 2.885,0.49 0.313,0.271 10 false *a 1.208,0.406 1.521,0.677 0.313,0.271 10 false 90°
*a Paint Mark
V100135

Engine Front


Mark the front of the connecting rod bolts with paint.


ii.

Further tighten the connecting rod bolts an additional 90° as shown in the illustration.


iii.

Check that the paint mark is now at a 90° angle to the front.



i.

Check that the crankshaft turns smoothly.


j.

Inspect the connecting rod thrust clearance.

Click hereEngine / Hybrid System>2NR-FE ENGINE MECHANICAL>CYLINDER BLOCK>INSPECTION