Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM(w/ Smart Entry and Start System) › 2016.04–2016.07
RM30M0E _58 Vehicle Interior _017111 THEFT DETERRENT / KEYLESS ENTRY _0090851 IMMOBILISER SYSTEM(w/ Smart Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/ Smart Entry and Start System)  B279A  Theft Deterrent System Communication Line High Fixation  


DESCRIPTION

When the communication line (IMI - EFIO) between the ECM and certification ECU (smart key ECU assembly) is stuck high, the ECM stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B279A Theft Deterrent System Communication Line High Fixation The communication line (IMI - EFIO) between the ECM and certification ECU (smart key ECU assembly) is stuck high (1 trip detection logic*1).
·

Wire harness or connector

·

Certification ECU (smart key ECU assembly)

·

ECM


DTC output confirmation operation:

Turn the engine switch on (IG) and wait 6 seconds.



*1: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started (initial ignition occurs and engine cranks, then ignition stops) Engine cannot be started

Related Data List and Active Test
DTC No. Data List and Active Test
B279A -

WIRING DIAGRAM

E272487E04
1.802,1.448 2.26,1.646 0.458,0.198 10 false IMI 2.167,1.281 2.479,1.479 0.313,0.198 10 false 16 2.49,1.281 2.802,1.479 0.313,0.198 10 false 19 2.125,1.438 2.51,1.667 0.385,0.229 10 false F82 2.448,1.448 2.833,1.677 0.385,0.229 10 false F81 2.188,1.635 2.5,1.865 0.313,0.229 10 false *1 2.51,1.635 2.823,1.865 0.313,0.229 10 false *2 1.479,2.552 1.948,2.802 0.469,0.25 10 false ECM 4.854,1.333 5.167,1.531 0.313,0.198 10 false 35 5.177,1.448 5.646,1.698 0.469,0.25 10 false EFIO 4.813,2.542 5.167,2.76 0.354,0.219 10 false F44 4.802,2.719 6.323,3.146 1.521,0.427 10 false Certification ECU (Smart Key ECU Assembly) 0.271,3.021 2.073,3.229 1.802,0.208 10 false *1: for Automatic Transaxle 0.271,3.333 2.073,3.542 1.802,0.208 10 false *2: for Manual Transaxle 0.094,0.073 3.396,0.313 3.302,0.24 12 false for 1NZ-FE, 2NZ-FE:

E347532E01
0.094,0.073 3.396,0.313 3.302,0.24 12 false for 1NR-FE, 2NR-FE: 5.177,1.677 5.635,1.875 0.458,0.198 10 false EFIO 1.823,1.677 2.281,1.875 0.458,0.198 10 false IMI 2.156,1.583 2.615,1.781 0.458,0.198 10 false 10 4.865,1.583 5.323,1.781 0.458,0.198 10 false 35 1.417,2.74 1.875,2.938 0.458,0.198 10 false F130 1.417,2.906 1.875,3.104 0.458,0.198 10 false ECM 4.802,2.885 6.365,3.281 1.563,0.396 10 false Certification ECU (Smart Key ECU Assembly) 4.802,2.719 5.438,2.948 0.635,0.229 10 false F44

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation."



HINT:

When DTC B279A and a certification ECU (smart key ECU assembly) DTC are output simultaneously, first perform troubleshooting for the certification ECU (smart key ECU assembly) DTC.


PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/ Smart Entry and Start System)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Turn the engine switch on (IG) and wait 10 seconds.


b.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/ Smart Entry and Start System)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Trouble Codes
50001 234
HINT:

If DTCs other than DTC B279A are output, troubleshoot those DTCs first.



Result:
Result Proceed to
DTC B279A is not output A
DTC B279A and other DTCs are output B



A

3.CHECK CONNECTION OF CONNECTOR

B

3.CHECK CONNECTION OF CONNECTOR
a.

Turn the engine switch off.


b.

Check that the connectors are properly connected to the ECM and certification ECU (smart key ECU assembly).

OK:

Connectors are properly connected.



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)

NG

CONNECT CONNECTORS PROPERLY

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)
a.

for 1NZ-FE, 2NZ-FE

i.

Disconnect the F44 certification ECU (smart key ECU assembly) connector.


ii.

Disconnect the F82*1 or F81*2 ECM connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F44-35 (EFIO) - F82-16 (IMI)*1 Always Below 1 Ω
F82-16 (IMI) - Body ground*1 Always 10 kΩ or higher
F44-35 (EFIO) - Body ground Always 10 kΩ or higher
F44-35 (EFIO) - F81-19 (IMI)*2 Always Below 1 Ω
F81-19 (IMI) - Body ground*2 Always 10 kΩ or higher



iv.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F82-16 (IMI) - Body ground*1 Always Below 1 V
F81-19 (IMI) - Body ground*2 Always Below 1 V


*1: for Automatic Transaxle

*2: for Manual Transaxle




b.

for 1NR-FE, 2NR-FE

i.

Disconnect the F44 certification ECU (smart key ECU assembly) connector.


ii.

Disconnect the F130 ECM connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F44-35 (EFIO) - F130-10 (IMI) Always Below 1 V
F130-10 (IMI) - Body ground Always 10 kΩ or higher
F44-35 (EFIO) - Body ground Always 10 kΩ or higher



iv.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F130-10 (IMI) - Body ground Always Below 1 V




Result:
Proceed to
OK
NG



OK

5.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) with a new one.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

6.REGISTER RECOGNITION CODES
6.REGISTER RECOGNITION CODES
a.

Register the recognition codes in the ECUs.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

7.REGISTER ECU COMMUNICATION ID
7.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

8.CLEAR DTC
8.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/ Smart Entry and Start System)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

Result:
Proceed to
NEXT



NEXT

9.CHECK FOR DTC
9.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/ Smart Entry and Start System)>DTC CHECK / CLEAR

HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.


Powertrain > Engine and ECT > Trouble Codes
50001 234
OK:

DTC B279A is not output.



Result:
Result Proceed to
OK A
NG (for 1NZ-FE) B
NG (for 2NZ-FE) C
NG (for 1NR-FE) D
NG (for 2NR-FE) E



A

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

B

C

D

E