The immobiliser system compares the ID code that is registered in the certification ECU (smart key ECU assembly) with the ID code of the transponder chip that is embedded in the electrical key transmitter sub-assembly.
The system unsets if these ID codes match. Thus, the certification ECU (smart key ECU assembly) and the ECM communicate with each other enabling the engine to start.
When using the GTS with the vehicle engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
The immobiliser system uses the LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the immobiliser system after confirming that the communication systems are functioning properly.
Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.
After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation."
When the ECM and certification ECU (smart key ECU assembly) DTC are output simultaneously, first perform troubleshooting for the ECM and certification ECU (smart key ECU assembly) DTC.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC is output | B |
A
B
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Normal Condition | Reference Value | Diagnostic Note |
|---|---|---|---|---|
| Immobiliser Fuel Cut | Immobiliser fuel cut status | ON or OFF | ON: Immobiliser fuel cut on
OFF: Immobiliser fuel cut off |
- |
| Tester Display |
|---|
| Immobiliser Fuel Cut |
| Result | Proceed to |
|---|---|
| "ON" is displayed on the Data List screen of the GTS (for 1NZ-FE with Automatic Transaxle) | A |
| "ON" is displayed on the Data List screen of the GTS (for 2NZ-FE with Automatic Transaxle) | B |
| "ON" is displayed on the Data List screen of the GTS (for 2NZ-FE with Manual Transaxle) | C |
| "ON" is displayed on the Data List screen of the GTS (for 1NR-FE) | D |
| "ON" is displayed on the Data List screen of the GTS (for 2NR-FE) | E |
| "OFF" is displayed on the Data List screen of the GTS | F |
A
B
C
D
Click hereEngine / Hybrid System>1NR-FE ENGINE CONTROL>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
E
Click hereEngine / Hybrid System>2NR-FE ENGINE CONTROL>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
F
Check that the engine starts 5 seconds after the engine switch turned on (IG).
Engine starts normally.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
for 1NZ-FE, 2NZ-FE
Using an oscilloscope, check the waveform.
| *A | for Automatic Transaxle | *B | for Manual Transaxle |
| *1 | Waveform (IMO) | *2 | Waveform (IMI) |
| *3 | Waveform A | *4 | Waveform B |
| *5 | Waveform C | - | - |
| *a | Component with harness connected
(ECM) |
*b | Approximately 160 ms |
| *c | Approximately 270 ms | *d | Approximately 40 ms |
| *e | Approximately 60 ms | - | - |
The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
| Item | Content |
|---|---|
| Tester Connection | F82-15 (IMO) - Body ground*1
F82-16 (IMI) - Body ground*1 F81-18 (IMO) - Body ground*2 F81-19 (IMI) - Body ground*2 |
| Tool Setting | 2 V/DIV., 500 ms./DIV. |
| Condition | Within 3 seconds after engine starts, or within 3 seconds after engine switch turned on (IG) after battery disconnected and reconnected |
*1: for Automatic Transaxle
*2: for Manual Transaxle
for 1NR-FE, 2NR-FE
Using an oscilloscope, check the waveform.
| *A | for CVT | *B | for Manual Transaxle |
| *1 | Waveform (IMO) | *2 | Waveform (IMI) |
| *3 | Waveform A | *4 | Waveform B |
| *5 | Waveform C | - | - |
| *a | Component with harness connected
(ECM) |
*b | Approximately 160 ms |
| *c | Approximately 270 ms | *d | Approximately 40 ms |
| *e | Approximately 60 ms | - | - |
The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
| Item | Content |
|---|---|
| Tester Connection | F130-9 (IMO) - Body ground
F130-10 (IMI) - Body ground |
| Tool Setting | 2 V/DIV., 500 ms./DIV. |
| Condition | Within 3 seconds after engine starts, or within 3 seconds after engine switch turned on (IG) after battery disconnected and reconnected |
| Result | Proceed to |
|---|---|
| Normal waveform | A |
| Waveform A not output, or has abnormal wavelength or shape | B |
| Waveform B not output, or has abnormal wavelength or shape (for 1NZ-FE) | C |
| Waveform B not output, or has abnormal wavelength or shape (for 2NZ-FE) | D |
| Waveform B not output, or has abnormal wavelength or shape (for 1NR-FE) | E |
| Waveform B not output, or has abnormal wavelength or shape (for 2NR-FE) | F |
| Waveform C not output, or has abnormal wavelength or shape | G |
A
B
C
D
E
F
G
Reregister the ECU communication ID.
Refer to Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Using a registered vehicle key, turn the engine switch on (IG).
Engine starts normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for 1NZ-FE, 2NZ-FE
Disconnect the F43 and F44 certification ECU (smart key ECU assembly) connectors.
Disconnect the F82*1 or F81*2 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F44-35 (EFIO) - F82-16 (IMI)*1 | Always | Below 1 Ω |
| F44-35 (EFIO) - Body ground | Always | 10 kΩ or higher |
| F82-16 (IMI) - Body ground*1 | Always | 10 kΩ or higher |
| F44-35 (EFIO) - F81-19 (IMI)*2 | Always | Below 1 Ω |
| F81-19 (IMI) - Body ground*2 | Always | 10 kΩ or higher |
*1: for Automatic Transaxle
*2: for Manual Transaxle
for 1NR-FE, 2NR-FE
Disconnect the F43 and F44 certification ECU (smart key ECU assembly) connectors.
Disconnect the F130 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F44-35 (EFIO) - F130-10 (IMI) | Always | Below 1 Ω |
| F44-35 (EFIO) - Body ground | Always | 10 kΩ or higher |
| F130-10 (IMI) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the certification ECU (smart key ECU assembly) with a new one.
Refer to Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Register the recognition codes in the ECUs.
Refer to Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Reregister the ECU communication ID.
Refer to Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Using a registered vehicle key, turn the engine switch on (IG).
Engine starts normally.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for 1NZ-FE with Automatic Transaxle) | B |
| NG (for 2NZ-FE with Automatic Transaxle) | C |
| NG (for 2NZ-FE with Manual Transaxle) | D |
| NG (for 1NR-FE) | E |
| NG (for 2NR-FE) | F |
A
B
C
D
E
Click hereEngine / Hybrid System>1NR-FE ENGINE CONTROL>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
F
Click hereEngine / Hybrid System>2NR-FE ENGINE CONTROL>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING