Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM › 2016.04–2017.10
RM30M0E _58 Vehicle Interior _017117 SEAT BELT _0084737 SEAT BELT WARNING SYSTEM J

SEAT BELT  SEAT BELT WARNING SYSTEM  Front Passenger Side Seat Belt Warning Light Malfunction  


DESCRIPTION

HINT:

The seat belt warning light on the combination meter assembly is used for both the driver seat and front passenger seat.


The separate type front seat cushion pad (occupant detection sensor) detects if the passenger seat is occupied and sends signals to the combination meter assembly. The front seat inner belt assembly (passenger side) detects the passenger seat belt condition and sends signals to the combination meter assembly. After receiving the signals from the separate type front seat cushion pad (occupant detection sensor) and front seat inner belt assembly (passenger side), the seat belt warning light on the combination meter assembly will blink or go off.

WIRING DIAGRAM

C294867E04
1.271,0.771 1.583,0.969 0.313,0.198 10 false SW 1.635,0.667 1.948,0.865 0.313,0.198 10 false 25 2.521,0.76 2.927,0.948 0.406,0.188 10 false F121 5.573,0.76 5.979,0.948 0.406,0.188 10 false F121 2.781,1.135 3.188,1.323 0.406,0.188 10 false 1 3.052,1.135 3.458,1.323 0.406,0.188 10 false B 4.042,1.125 4.448,1.313 0.406,0.188 10 false B 4.406,1.167 6.115,1.802 1.708,0.635 10 false Front Seat Inner Belt Assembly (passenger side) 3.75,1.125 4.156,1.313 0.406,0.188 10 false 3 2.448,1.865 4.875,2.604 2.427,0.74 10 false Separate Type Front Seat Cushion Pad (Occupant Detection Sensor) 0.563,1.844 0.948,2.052 0.385,0.208 10 false F38 0.552,2.01 1.76,2.385 1.208,0.375 10 false Combination Meter Assembly 2.646,0.563 3.052,0.75 0.406,0.188 10 false 3 5.688,0.563 6.094,0.75 0.406,0.188 10 false 2 2.948,0.646 3.354,0.833 0.406,0.188 10 false + 5.365,0.656 5.771,0.844 0.406,0.188 10 false E

PROCEDURE

1.READ VALUE USING GTS (P-SEATBELT BUCKLE SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
P-Seatbelt Buckle SW Front seat inner belt assembly (Passenger Side) ON or OFF OFF: Front passenger seat belt not fastened
ON: Front passenger seat belt fastened
The front passenger seat is occupied
Body Electrical > Combination Meter > Data List
Tester Display
P-Seatbelt Buckle SW
50003 122 7

OK:

The GTS display changes correctly in response to the front passenger seat belt condition.


Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

2.INSPECT SEPARATE TYPE FRONT SEAT CUSHION PAD (OCCUPANT DETECTION SENSOR)
2.INSPECT SEPARATE TYPE FRONT SEAT CUSHION PAD (OCCUPANT DETECTION SENSOR)
a.
B332793C01
0.177,0.167 0.49,0.323 0.313,0.156 10 *a
*a Component without harness connected
(Separate Type Front Seat Cushion Pad (Cccupant Detection Sensor))


Remove the separate type front seat cushion pad (occupant detection sensor).

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY>DISASSEMBLY


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 3 Front passenger seat occupied Below 100 Ω
1 - 3 Front passenger seat not occupied 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT FRONT SEAT INNER BELT ASSEMBLY (PASSENGER SIDE)

NG

REPLACE SEPARATE TYPE FRONT SEAT CUSHION PAD (OCCUPANT DETECTION SENSOR)

3.INSPECT FRONT SEAT INNER BELT ASSEMBLY (PASSENGER SIDE)
a.
B332790C07
1.646,1.594 0.927,2.469 true 2.052,1.594 2.677,2.448 true 0.135,0.073 0.448,0.229 0.313,0.156 10 false *a 0.865,2.5 1.021,2.698 0.156,0.198 10 false + 2.667,2.479 2.823,2.677 0.156,0.198 10 false E
*a Component without harness connected
(Front Seat Inner Belt Assembly (Passenger Side))


Remove the front seat inner belt assembly (passenger side).

Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (+) - 1 Always Below 1 Ω
2 (E) - 3 Front passenger seat belt unfastened Below 1 Ω
2 (E) - 3 Front passenger seat belt fastened 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT ASSEMBLY (PASSENGER SIDE) - COMBINATION METER ASSEMBLY AND BODY GROUND)

NG

REPLACE FRONT SEAT INNER BELT ASSEMBLY (PASSENGER SIDE)

4.CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT ASSEMBLY (PASSENGER SIDE) - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the F38 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F38-25 (SW) - F121-3 (+) Always Below 1 Ω
F38-25 (SW) or F121-3 (+) - Body ground Always 10 kΩ or higher
F121-2 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR