AIR CONDITIONING AMPLIFIER ASSEMBLY (for 1NZ-FE or 2NZ-FE)
Check from the rear of the connector while it is connected to the air conditioning amplifier assembly.
| Terminal No.
(Symbol) |
Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F40-2 (AC1) - F40-11 (GND)*1 | L - W-B | Magnet clutch request signal | ·
Engine running ·
Blower switch: 1 ·
A/C switch: Off |
11 to 14 V |
·
Engine running ·
Blower switch: 1 ·
A/C switch: On (magnet clutch on) |
Below 1 V | |||
| F40-3 (PSW) - F40-11 (GND)*1 | P - W-B | Air conditioning pressure switch signal | ·
Engine running ·
Refrigerant pressure normal ·
Blower switch: 1 ·
A/C switch: On |
Below 1 V |
·
Engine running ·
Refrigerant pressure abnormal (less than 196 kPa [2.0 kgf/cm2, 28 psi] or more than 3140 kPa [32.0 kgf/cm2, 455.3 psi]) ·
Blower switch: 1 ·
A/C switch: On |
11 to 14 V | |||
| F40-5 (SG-2) - Body ground | GR - Body ground | Ground for evaporator temperature sensor | Always | Below 1 Ω |
| F40-6 (TE) - F40-5 (SG-2) | BR - GR | Evaporator temperature sensor signal | ·
Ignition switch ON ·
Evaporator temperature (ambient): 0°C (32°F) |
3.89 to 5.93 V |
·
Ignition switch ON ·
Evaporator temperature (ambient): 15°C (59°F) |
2.35 to 3.59 V | |||
·
Ignition switch ON ·
Evaporator temperature (ambient): 20°C (68°F) |
1.97 to 3.01 V | |||
·
Ignition switch ON ·
Evaporator temperature (ambient): 25°C (77°F) |
1.64 to 2.51 V | |||
·
Ignition switch ON ·
Evaporator temperature (ambient): 30°C (86°F) |
1.37 to 2.1 V | |||
| F40-7 (IG+) - F40-11 (GND) | G - W-B | Power source (IG) | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V | |||
| F40-9 (A/C) - F40-11 (GND)*1 | G - W-B | A/C switch signal | ·
Engine running ·
Blower switch: 1 ·
A/C switch: Off |
11 to 14 V |
·
Engine running ·
Blower switch: 1 ·
A/C switch: On |
Below 1 V | |||
| F40-11 (GND) - Body ground | W-B - Body ground | Ground for main power supply | Always | Below 1 Ω |
*1: w/ Cooler System
AIR CONDITIONING AMPLIFIER ASSEMBLY (for 1NR-FE or 2NR-FE)
Check from the rear of the connector while it is connected to the air conditioning amplifier assembly.
| Terminal No.(Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F124-1 (IG+) - F124-14 (GND) | G - W-B | Power source (IG) | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V | |||
| F124-5 (TAM) - F124-15 (SG-2)*1 | BE - L | Ambient temperature sensor signal | Ignition switch ON at 25°C (77°F) | 1.35 to 1.75 V |
| F124-9 (PSW) - F124-14 (GND)*1 | SB - W-B | Air conditioner pressure sensor signal | ·
Engine running ·
Refrigerant pressure normal ·
Blower switch: 1 ·
A/C switch: On |
0.74 to 4.62 V |
·
Engine running ·
Refrigerant pressure abnormal (less than 196 kPa [2.0 kgf/ cm2, 28 psi]) ·
Blower switch: 1 ·
A/C switch: On |
Below 0.74 V | |||
·
Engine running ·
Refrigerant pressure abnormal (more than 3140 kPa [32.0 kgf/cm2, 455.3 psi]) ·
Blower switch: 1 ·
A/C switch: On |
4.62 V or higher | |||
| F124-11 (TX+) - F124-14 (GND) | V - W-B | CAN communication signal | Ignition switch ON | Pulse generation |
| F124-12 (TX-) - F124-14 (GND) | W - W-B | CAN communication signal | Ignition switch ON | Pulse generation |
| F124-14 (GND) - Body ground | W-B - Body ground | Ground for main power supply | Always | Below 1 Ω |
| F124-15 (SG-2) - Body ground*1 | L - Body ground | Ground for ambient temperature sensor and air conditioner pressure sensor | Always | Below 1 Ω |
| F124-20 (HR) - F124-14 (GND) | P - W-B*2
R - W-B*3 |
Blower motor relay operation signal | ·
Ignition switch ON ·
Blower switch: 1 |
Below 1 V |
·
Ignition switch ON ·
Blower switch: Off |
11 to 14 V | |||
| F124-26 (SBLW) - F124-14 (GND) | G - W-B*2
L - W-B*3 |
Blower motor ON signal | ·
Ignition switch ON ·
Blower switch: Off |
11 to 14 V |
·
Ignition switch ON ·
Blower switch: 1 |
Below 1 V | |||
| F124-29 (TE) - F124-34 (SG-1) | BR - BE | Evaporator temperature sensor signal | ·
Ignition switch ON ·
Evaporator temperature (ambient): 0°C (32°F) |
2.0 to 2.4 V |
·
Ignition switch ON ·
Evaporator temperature (ambient): 15°C (59°F) |
1.4 to 1.8 V | |||
| F124-30 (S5-3) - F124-15 (SG-2)*1 | LG - L | Power supply for air conditioner pressure sensor | Ignition switch ON | 4.75 to 5.25 V |
| F124-31 (A/C) - F124-14 (GND)*1 | G - W-B | A/C switch signal | ·
Engine running ·
Blower switch: 1 ·
A/C switch: Off |
11 to 14 V |
·
Engine running ·
Blower switch: 1 ·
A/C switch: On |
Below 1 V | |||
| F124-34 (SG-1) - Body ground | BE - Body ground | Ground for evaporator temperature sensor | Always | Below 1 Ω |
| F124-36 (AC1) - F124-14 (GND)*1 | L - W-B | Magnet clutch request signal | ·
Engine running ·
Blower switch: 1 ·
A/C switch: Off |
11 to 14 V |
·
Engine running ·
Blower switch: 1 ·
A/C switch: On (magnet clutch on) |
Below 1 Ω |
*1: w/ Cooler System
*2: Through No. 9 Junction Connector
*3: Not Through No. 9 Junction Connector
ECM
for 1NZ-FE with Automatic Transaxle:
Click hereEngine / Hybrid System>1NZ-FE ENGINE CONTROL>SFI SYSTEM(for Automatic Transaxle)>TERMINALS OF ECM
for 1NZ-FE with Manual Transaxle:
Click hereEngine / Hybrid System>1NZ-FE ENGINE CONTROL>SFI SYSTEM(for Manual Transaxle)>TERMINALS OF ECM
for 1NZ-FE with Air Fuel Ratio Sensor:
Click hereEngine / Hybrid System>1NZ-FE ENGINE CONTROL>SFI SYSTEM(w/ Air Fuel Ratio Sensor)>TERMINALS OF ECM
for 2NZ-FE with Automatic Transaxle:
Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM(for Automatic Transaxle)>TERMINALS OF ECM
for 2NZ-FE with Manual Transaxle:
Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM(for Manual Transaxle)>TERMINALS OF ECM
for 1NR-FE:
Click hereEngine / Hybrid System>1NR-FE ENGINE CONTROL>SFI SYSTEM>TERMINALS OF ECM
for 2NR-FE:
Click hereEngine / Hybrid System>2NR-FE ENGINE CONTROL>SFI SYSTEM>TERMINALS OF ECM