Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Manual Air Conditioning System) › 2016.04–2017.10
RM30M0E _58 Vehicle Interior _017118 HEATING / AIR CONDITIONING _0086991 AIR CONDITIONING SYSTEM(for Manual Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)  B1413  Evaporator Temperature Sensor Circuit  


DESCRIPTION

The No. 1 cooler thermistor is installed on the evaporator in the air conditioner unit to detect the temperature of the cooled air that has passed through the evaporator and is used to control the air conditioning. It sends signals to the air conditioning amplifier assembly. The resistance of the No. 1 cooler thermistor changes in accordance with the temperature of the cooled air that has passed through the evaporator. As the temperature decreases, the resistance increases. As the temperature increases, the resistance decreases.

The air conditioning amplifier assembly applies voltage (5 V) to the No. 1 cooler thermistor and reads voltage changes as the resistance of the No. 1 cooler thermistor. This sensor is used for frost prevention.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory
B1413 Evaporator Temperature Sensor Circuit Open or short in No. 1 cooler thermistor circuit
·

No. 1 cooler thermistor

·

Harness or connector between No. 1 cooler thermistor and air conditioning amplifier assembly

·

Air conditioning amplifier assembly


Memorized
(4 seconds or more)*1

*1: The air conditioning amplifier assembly stores this DTC if the malfunction has occurred for the period of time indicated in the brackets.


WIRING DIAGRAM

E236721E83
2.146,0.448 2.531,0.844 0.385,0.396 10 false 1 2.146,1.396 2.646,1.729 0.5,0.333 10 false 2 5.115,0.448 5.552,0.75 0.438,0.302 10 false 29 5.125,1.406 5.521,1.708 0.396,0.302 10 false 34 5.396,0.542 6.146,0.958 0.75,0.417 10 false TE 5.396,1.49 6.146,1.833 0.75,0.344 10 false SG-1 1.135,1.938 1.458,2.115 0.323,0.177 10 false F54 1.125,2.104 2.615,2.313 1.49,0.208 10 false No. 1 Cooler Thermistor 5.063,1.885 5.5,2.063 0.438,0.177 10 false F124 5.052,2.052 6.635,2.521 1.583,0.469 10 false Air Conditioning Amplifier Assembly

PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Air Conditioner / Data List.


e.

According to the display on the GTS, read the Data List.

Body Electrical > Air Conditioner > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Evaporator Fin Thermistor No. 1 cooler thermistor Min.: -29.70°C (-21.46°F)
Max.: 59.55°C (139.19°F)
Actual evaporator temperature displayed -
Body Electrical > Air Conditioner > Data List
Tester Display
Evaporator Fin Thermistor
50003 121 3
OK:

The display is as specified in the normal condition column.



Result:
Result Proceed to
NG A
OK (When troubleshooting according to Problem Symptoms Table) B
OK (When troubleshooting according to the DTC) C



A

2.INSPECT NO. 1 COOLER THERMISTOR

B

C

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

2.INSPECT NO. 1 COOLER THERMISTOR


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (NO. 1 COOLER THERMISTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

3.CHECK HARNESS AND CONNECTOR (NO. 1 COOLER THERMISTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Disconnect the F54 No. 1 Cooler thermistor connector.


b.

Disconnect the F124 air conditioning amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F124-29 (TE) - F54-1 Always Below 1 Ω
F124-34 (SG-1) - F54-2 Always Below 1 Ω
F124-29 (TE) or F54-1 - Body ground Always 10 kΩ or higher
F124-34 (SG-1) or F54-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR