Home › Engine / Hybrid System › 1NZ-FE ENGINE CONTROL › SFI SYSTEM(for Manual Transaxle) › 2016.04–2016.07
RM30M0E _51 Engine / Hybrid System _017071 1NZ-FE ENGINE CONTROL _0090158 SFI SYSTEM(for Manual Transaxle) J

1NZ-FE ENGINE CONTROL  SFI SYSTEM(for Manual Transaxle)  Fuel Pump Control Circuit  


DESCRIPTION

When the engine is cranked, the ST relay drive signal output from the ignition or starter switch assembly is input into the STA terminal of the ECM, and the NE signal generated by the crankshaft position sensor is also input into the NE+ terminal. The ECM interprets that the engine is cranked, and turns transistor Tr1 in the ECM internal circuit on. Current flows to the C/OPN (Circuit Opening) relay by turning Tr1 on. Then, the fuel pump operates.

While the NE signal is input into the ECM with the engine running, the ECM turns Tr1 on continuously.

WIRING DIAGRAM

A382576E01
1.073,0.167 1.531,0.365 0.458,0.198 10 false AM2 2.188,0.167 2.646,0.365 0.458,0.198 10 false IG2 2.542,0.167 3,0.365 0.458,0.198 10 false 6 0.844,0.167 1.302,0.365 0.458,0.198 10 false 5 0.667,0.75 3.073,1.021 2.406,0.271 10 false Ignition or Starter Switch Assembly 0.667,0.583 3.073,0.854 2.406,0.271 10 false F77 3.125,1.156 3.583,1.354 0.458,0.198 10 false 2H 3.198,3.313 3.656,3.51 0.458,0.198 10 false 2K 4.635,1.938 5.094,2.135 0.458,0.198 10 false 2L 4.625,2.354 5.083,2.552 0.458,0.198 10 false 2O 4.635,2.896 5.094,3.094 0.458,0.198 10 false 2L 1.135,1.375 1.594,1.573 0.458,0.198 10 false 2H 1.135,2.354 1.594,2.552 0.458,0.198 10 false 2B 0.948,3.51 3.76,3.865 2.813,0.354 10 false Driver Side Junction Block Assembly 6.104,1.802 7.156,2.104 1.052,0.302 10 false FC 5.75,2.906 7.156,3.167 1.406,0.26 10 false F81 5.75,4.198 7.156,4.458 1.406,0.26 10 false F81 4.26,4.969 5.375,5.417 1.115,0.448 10 false from STA Signal Circuit 5.75,5.677 7.156,5.938 1.406,0.26 10 false B32 5.75,6.052 7.156,6.313 1.406,0.26 10 false B32 5.75,1.927 7.156,2.188 1.406,0.26 10 false F81 6.104,2.906 7.156,3.208 1.052,0.302 10 false MREL 6.104,4.198 7.156,4.5 1.052,0.302 10 false +B 6.104,4.99 7.156,5.292 1.052,0.302 10 false STA 6.104,5.677 7.156,5.979 1.052,0.302 10 false NE+ 6.104,6.052 7.156,6.354 1.052,0.302 10 false NE- 6.313,6.313 6.99,6.635 0.677,0.323 10 false ECM 5.792,1.75 7.156,2.01 1.365,0.26 10 false 11 5.833,2.719 6.833,3.063 1,0.344 10 false 2 5.792,4.01 7.156,4.271 1.365,0.26 10 false 10 5.833,4.802 6.917,5.052 1.083,0.25 10 false 3 5.792,5.5 7.156,5.76 1.365,0.26 10 false 26 5.792,5.875 7.156,6.135 1.365,0.26 10 false 24 5.75,4.979 7.156,5.24 1.406,0.26 10 false F81 3.167,5.875 6.063,6.354 2.896,0.479 10 false from Crankshaft Position Sensor 2.438,4.76 3.844,5.406 1.406,0.646 10 false Fuel Suction Tube with Pump and Gauge Assembly 2.438,4.594 3.844,5.24 1.406,0.646 10 false F28 1.604,4.865 2.365,5.125 0.76,0.26 10 false Fuel Pump 1.542,4.313 2,4.51 0.458,0.198 10 false 4 1.542,4.531 2,4.729 0.458,0.198 10 false B 1.542,5.208 2,5.406 0.458,0.198 10 false E 1.542,5.427 2,5.625 0.458,0.198 10 false 5 2.49,3.177 2.948,3.375 0.458,0.198 10 false EFI 3.75,2.688 4.427,2.917 0.677,0.229 10 false C/OPN 3.281,1.542 4.083,1.76 0.802,0.219 10 false IG2 NO. 1 1.667,1.75 2.469,1.969 0.802,0.219 10 false AM2 1.604,2.5 2.406,2.719 0.802,0.219 10 false EFI-MAIN 1.146,2.906 1.604,3.104 0.458,0.198 10 false 2J 1.188,2.729 1.646,2.927 0.458,0.198 10 false 7 1.188,2.177 1.646,2.375 0.458,0.198 10 false 1 1.188,1.198 1.646,1.396 0.458,0.198 10 false 5 2.896,1.146 3.354,1.344 0.458,0.198 10 false 1 4.667,1.75 5.125,1.948 0.458,0.198 10 false 8 4.667,2.177 5.125,2.375 0.458,0.198 10 false 7 4.667,2.719 5.125,2.917 0.458,0.198 10 false 9 2.969,3.313 3.427,3.51 0.458,0.198 10 false 4 0.552,5.313 1.625,5.51 1.073,0.198 10 false Battery 0.344,4.604 1.417,4.802 1.073,0.198 10 false FL MAIN 0.344,3.833 1.417,4.031 1.073,0.198 10 false MAIN

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP / SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

Powertrain > Engine and ECT > Active Test
Tester Display
Control the Fuel Pump / Speed
50004 234 5

e.

Check whether the fuel pump operating sound occurs when performing the Active Test on the GTS.


Result:
Result Proceed to
Fuel pump operating sound does not occur A
Fuel pump operating sound occurs B



A

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP/SPEED)

B

11.READ VALUE USING GTS (STARTER SIGNAL)
2.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP/SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump/Speed.

Powertrain > Engine and ECT > Active Test
Tester Display
Control the Fuel Pump / Speed
50004 234 5

e.

Check whether the C/OPN relay operating sound occurs when performing the Active Test on the GTS.

OK:

Relay operating sounds can be heard from the relay.



Result:
Proceed to
OK
NG



OK

3.INSPECT FUEL PUMP

NG

7.CHECK TERMINAL VOLTAGE (FC TERMINAL VOLTAGE)
3.INSPECT FUEL PUMP
a.

Result:
Proceed to
OK
NG



OK

4.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY (C/OPN RELAY)

NG

4.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY (C/OPN RELAY)
a.

Remove the driver side junction block assembly

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2K-4 - 2O-7 When battery voltage not applied to terminals 2L-8 and 2H-1 10 kΩ or higher
When battery voltage applied to terminals 2L-8 and 2H-1 Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY)

NG

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY)
a.

Remove the driver side junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Disconnect the F28 fuel suction tube with pump and gauge assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2O-7 - F28-4 (B) Always Below 1 Ω
2O-7 or F28-4 (B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY - BODY GROUND)
a.

Disconnect the F28 fuel suction tube with pump and gauge assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F28-5 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK TERMINAL VOLTAGE (FC TERMINAL VOLTAGE)
a.
A295436C02
0.76,0.406 1.146,0.677 0.385,0.271 1.271,1.792 1.292,1.104 true 0.844,0.469 1.302,0.667 0.458,0.198 10 false F81 0.125,0.135 0.438,0.292 0.313,0.156 10 false *a 1.167,1.833 1.479,2.031 0.313,0.198 10 false FC
*a Component with harness connected
(ECM)


Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F81-11 (FC) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

8.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY (C/OPN RELAY)
8.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY (C/OPN RELAY)
a.

Remove the driver side junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2K-4 - 2O-7 When battery voltage not applied to terminals 2L-8 and 2H-1 10 kΩ or higher
When battery voltage applied to terminals 2L-8 and 2H-1 Below 1 Ω



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - ECM)

NG

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY

9.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - ECM)
a.

Remove the driver side junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Disconnect the F81 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2L-8 - F81-11 (FC) Always Below 1 Ω
2L-8 or F81-11 (FC) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - IGNITION OR STATRTER SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - IGNITION OR STATRTER SWITCH ASSEMBLY)
a.

Remove the driver side junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Disconnect the F7 ignition or starter switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2H-1 - F7-6 (IG2) Always Below 1 Ω
2H-1 or F7-6 (IG2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.

Powertrain > Engine and ECT > Data List
Tester Display
Starter Signal
50003 234 118

e.

Check the result when the ignition switch is ON and the engine starts.

OK:
Condition Starter Signal
Ignition switch ON OFF
Engine Started ON



Result:
Proceed to
OK
NG



OK

12.READ VALUE USING GTS (ENGINE SPEED)

NG

12.READ VALUE USING GTS (ENGINE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.

Powertrain > Engine and ECT > Data List
Tester Display
Engine Speed
50003 234 9

e.

Read the values displayed on the GTS while cranking.

OK:

Values are displayed continuously.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG