Home › Drivetrain › CLUTCH › CLUTCH UNIT(for C50) › 2016.04–2016.07
RM30M0E _52 Drivetrain _017089 CLUTCH _0091140 CLUTCH UNIT(for C50) A

CLUTCH  CLUTCH UNIT(for C50)  INSTALLATION  


PROCEDURE

Hide 31250 1.INSTALL CLUTCH DISC ASSEMBLY

a.
C293452C01
2.281,1.615 2.74,1.615 false 1.76,3.521 2.135,3.833 false 0.635,2.333 1.052,2.521 false 1.344,2.646 1.771,2.344 false 1.813,2.26 2.125,2.417 0.313,0.156 10 false *1 0.479,2.25 0.792,2.406 0.313,0.156 10 false *2 2.781,1.531 3.24,1.729 0.458,0.198 10 false SST 2.188,3.76 2.646,3.958 0.458,0.198 10 false SST
*1 Clutch Disc Assembly
*2 Flywheel Sub-assembly


Insert SST into the clutch disc assembly, and then insert them both into the flywheel sub-assembly.

SST
09301-00210  

NOTICE:

Insert the clutch disc assembly in the correct direction.



Hide 31210 2.INSTALL CLUTCH COVER ASSEMBLY

a.
C283239C01
1.125,0.76 0.76,0.875 0.76,0.875 1.052,0.719 true 2.646,1.406 2.052,1.083 true 0.594,0.781 0.906,0.938 0.313,0.156 10 false *a 2.198,0.031 2.75,0.26 0.552,0.229 10 false 1 (*b), 4 2.26,1.875 2.417,2.073 0.156,0.198 10 false 2 0.646,1.063 0.802,1.26 0.156,0.198 10 false 3 2.698,0.906 2.854,1.104 0.156,0.198 10 false 5 1.24,1.979 1.396,2.177 0.156,0.198 10 false 6 1.115,0.063 1.271,0.26 0.156,0.198 10 false 7 2.698,1.333 3.156,1.531 0.458,0.198 10 false SST
*a Matchmark
*b Temporarily Tighten


Align the matchmark on the clutch cover assembly with that on the flywheel sub-assembly.


b.

Using SST, center the clutch disc assembly, and following the procedure shown in the illustration, tighten the 6 bolts in order, starting with the bolt located near the knock pin at the top.

SST
09301-00210  

Torque:
19.1 N*m (195 kgf*cm, 14 ft.*lbf)

HINT:
·

Following the order in the illustration, tighten the bolts evenly one at a time.

·

Move SST up and down, right and left lightly after checking that the clutch disc assembly is in the center, and tighten the bolts.




Hide 31210 3.INSPECT AND ADJUST CLUTCH COVER ASSEMBLY

a.
C283240

Using a dial indicator with a roller instrument, measure the diaphragm spring tip alignment.

Maximum non-alignment:

0.5 mm (0.0197 in.)



b.
C283241E01
2.365,1.25 2.646,0.604 false 2.688,0.5 3.146,0.698 0.458,0.198 10 false SST

If the alignment is not as specified, using SST, adjust the diaphragm spring tip alignment.

SST
09333-00013  


Hide 31236B 4.INSTALL RELEASE FORK SUPPORT (for 2NR-FE)

a.

Clean and degrease the release fork support and the installation hole in the manual transaxle assembly.


b.
C358098C01
1.844,1.854 1.844,1.583 false 1.781,1.865 2.094,2.021 0.313,0.156 10 false *a
*a Adhesive


Apply adhesive to 2 or 3 threads on the end of the release fork support.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

To prevent contamination by foreign matter, install immediately after applying adhesive.



c.

Using a 19 mm deep socket wrench, install the release fork support to the manual transaxle assembly.

Torque:
36.8 N*m (375 kgf*cm, 27 ft.*lbf)


Hide 31236B 5.INSTALL RELEASE FORK SUPPORT (for 1NZ-FE)

a.

Using a 19 mm deep socket wrench, install the release fork support to the manual transaxle assembly.

Torque:
36.8 N*m (375 kgf*cm, 27 ft.*lbf)


Hide 31126 6.INSTALL CLUTCH RELEASE FORK BOOT

a.

Install the clutch release fork boot to the manual transaxle assembly.


Hide 31232A 7.INSTALL RELEASE BEARING HUB CLIP

a.

Install the release bearing hub clip to the clutch release bearing assembly.


Hide 31237 8.INSTALL CLUTCH RELEASE FORK SUPPORT BOOT (for 2NR-FE)

a.
C359307C01
0.708,1.625 0.708,1.875 false 1.49,0.417 1.719,0.417 1.719,0.417 1.719,0.948 true 0.656,1.885 0.969,2.042 0.313,0.156 10 false *a 1.333,0.333 1.646,0.49 0.313,0.156 10 false *b
*a Portion A
*b Paint Mark


Install the clutch release fork support boot to the release fork anti-rattle spring.

NOTICE:

Assemble the components so that the paint mark of the clutch release fork support boot and portion A of the release fork anti-rattle spring are positioned as shown in the illustration.



b.
C359308

Install the release fork anti-rattle spring to the clutch release fork sub-assembly.


Hide 31204 9.INSTALL CLUTCH RELEASE FORK SUB-ASSEMBLY (for 2NR-FE)

a.
C359309C01
0,0 0,0 false
V100135

Release Hub Grease


Apply release hub grease to the contact surfaces of the clutch release fork sub-assembly and the clutch release bearing assembly, the clutch release fork sub-assembly and the release cylinder push rod, and the clutch release fork sub-assembly and the release fork support.

Grease:

Toyota Genuine Release Hub Grease or equivalent



b.
C359310C01
0,0 0,0 false
V100135

Release Hub Grease


Apply release hub grease to the clutch release fork support boot.

Grease:

Toyota Genuine Release Hub Grease or equivalent



c.

Engage the release bearing hub clip and install the clutch release fork sub-assembly to the clutch release bearing assembly.


Hide 31204 10.INSTALL CLUTCH RELEASE FORK SUB-ASSEMBLY (for 1NZ-FE)

a.
C246398C01
0,0 3.427,0 false
V100135

Release Hub Grease


Apply release hub grease to the contact surfaces of the clutch release fork sub-assembly and the clutch release bearing assembly, the clutch release fork sub-assembly and the release cylinder push rod, and the clutch release fork sub-assembly and the release fork support.

Grease:

Toyota Genuine Release Hub Grease or equivalent



b.

Engage the release bearing hub clip and install the clutch release fork sub-assembly to the clutch release bearing assembly.


Hide 31230 11.INSTALL CLUTCH RELEASE BEARING ASSEMBLY (for 2NR-FE)

a.

Install the clutch release bearing assembly with the clutch release fork sub-assembly to the manual transaxle assembly.


b.

Engage the clutch release fork support boot to the release fork support.

NOTICE:

After the installation, move the clutch release fork sub-assembly forward and backward to check that the clutch release bearing assembly slides smoothly.



c.
C358093C01
0,0 0,0 false
V100135

Clutch Spline Grease


Apply clutch spline grease to the input shaft spline.

Grease:

Toyota Genuine Clutch Spline Grease or equivalent



Hide 31230 12.INSTALL CLUTCH RELEASE BEARING ASSEMBLY (for 1NZ-FE)

a.

Install the clutch release bearing assembly with the clutch release fork sub-assembly to the manual transaxle assembly.


b.

Engage the release fork anti-rattle spring to the release fork support.

NOTICE:

After the installation, move the clutch release fork sub-assembly forward and backward to check that the clutch release bearing assembly slides smoothly.



c.
C358093C01
0,0 0,0 false
V100135

Clutch Spline Grease


Apply clutch spline grease to the input shaft spline.

Grease:

Toyota Genuine Clutch Spline Grease or equivalent