Home › Drivetrain › C50 MANUAL TRANSMISSION / TRANSAXLE › MANUAL TRANSAXLE ASSEMBLY(for 1NZ-FE) › 2014.03–2016.07
RM30M0E _52 Drivetrain _017090 C50 MANUAL TRANSMISSION / TRANSAXLE _0091172 MANUAL TRANSAXLE ASSEMBLY(for 1NZ-FE) A

C50 MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSAXLE ASSEMBLY(for 1NZ-FE)  INSTALLATION  


PROCEDURE

Hide 33403K 1.INSTALL SPEEDOMETER DRIVEN HOLE COVER SUB-ASSEMBLY (w/ ABS)

a.

Apply a light coat of gear oil to a new O-ring and install it to the speedometer driven hole cover sub-assembly.

NOTICE:

Do not twist the O-ring.



b.

Install the speedometer driven hole cover sub-assembly to the manual transaxle assembly with the bolt.

Torque:
11.3 N*m (115 kgf*cm, 8 ft.*lbf)

NOTICE:

Make sure that the O-ring is not damaged or does not jump out of position during installation.



Hide 83181G 2.INSTALL SPEEDOMETER SENSOR (w/o ABS)

a.

Apply a light coat of gear oil to a new O-ring and install it to the speedometer sensor.

NOTICE:

Do not twist the O-ring.



b.

Install the speedometer driven gear to the speedometer sensor with the clip.


c.

Install the speedometer sensor to the manual transaxle assembly with the bolt.

Torque:
11.3 N*m (115 kgf*cm, 8 ft.*lbf)

NOTICE:

Make sure that the O-ring is not damaged or does not jump out of position during installation.



Hide 3.INSTALL WIRE HARNESS CLAMP BRACKET

a.

Install the 2 wire harness clamp brackets to the manual transaxle assembly with the 2 bolts.

Torque:
12.8 N*m (131 kgf*cm, 9 ft.*lbf)


Hide 30300 4.INSTALL MANUAL TRANSAXLE ASSEMBLY

a.
C283234C01
0,0 0,0 false
V100135

Clutch Spline Grease


Apply clutch spline grease to the input shaft spline.

Grease:

Toyota Genuine Clutch Spline Grease or equivalent



b.
C265749C02
1.333,0.271 2.719,0.167 2.719,0.167 2.531,0.844 true 2.75,0.063 3.063,0.219 0.313,0.156 10 false *1
*1 Knock Pin


Confirm that the 2 knock pins are installed on the engine assembly and are not damaged.


c.

Align the input shaft with the clutch disc assembly and install the manual transaxle assembly to the engine assembly.

NOTICE:
·

Make sure that the wire harness or similar items are not pinched between the contact surfaces.

·

Do not forcibly pry on the manual transaxle assembly.

·

When mounting the manual transaxle assembly to the engine assembly, make sure to securely fit the knock pins into the knock holes.

·

When tightening the bolts, be sure that the contact surfaces of the engine assembly and manual transaxle assembly are in close contact with one another.




d.
C261396E01
2.5,0.042 2.656,0.24 0.156,0.198 10 false A 0.917,0.083 1.073,0.281 0.156,0.198 10 false A 0.719,0.708 0.844,0.875 0.125,0.167 10 true B 1.021,1.719 1.146,1.885 0.125,0.167 10 true B 1.479,1.958 1.604,2.115 0.125,0.156 10 false B 2.146,1.969 2.271,2.125 0.125,0.156 10 false B 2.635,1.802 2.76,1.958 0.125,0.156 10 false B

Install the 7 bolts.

Torque:
33 N*m (337 kgf*cm, 24 ft.*lbf)

HINT:
·

Bolt A: Install from manual transaxle assembly side

·

Bolt B: Install from engine assembly side




e.
A192239C42
1.698,1.5 1.698,1.74 false 1.646,1.75 1.823,1.906 0.177,0.156 10 false *a
*a Adhesive


Clean and degrease the engine mounting bracket LH installation bolts and bolt holes.


f.

Apply adhesive to 2 or 3 threads on the ends of the 4 bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

To prevent contamination by foreign matter, install immediately after applying adhesive.



g.
C286334C01
0.656,1.5 1.177,1.688 0.521,0.188 10 true 1 (*a), 5 1.906,1.104 2.042,1.292 0.135,0.188 10 false 2 2.271,1.542 2.406,1.729 0.135,0.188 10 false 3 0.76,0.99 0.875,1.167 0.115,0.177 10 true 4
*a Temporarily Tighten


Install the engine mounting bracket LH to the manual transaxle assembly with the 4 bolts in the order shown in the illustration.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)


h.
C283173C04
2.604,0.281 3.125,0.281 true 2.063,0.708 2.625,0.906 0.563,0.198 10 true 1 (*b), 6 1.823,1.917 1.938,2.083 0.115,0.167 10 true 2 1.156,0.542 1.281,0.698 0.125,0.156 10 true 3 2.646,1.469 2.76,1.635 0.115,0.167 10 true 4 1.969,0.188 2.083,0.354 0.115,0.167 10 true 5 3.146,0.177 3.354,0.375 0.208,0.198 10 false *a
*a Hook
*b Temporarily Tighten


Engage the hook to temporarily install the engine mounting insulator LH to the body.


i.

Install the 5 bolts in the order shown in the illustration.

Torque:
52 N*m (530 kgf*cm, 38 ft.*lbf)


j.
C283172

Install the engine mounting insulator LH to the engine mounting bracket LH with the bolt and nut.

Torque:
52 N*m (530 kgf*cm, 38 ft.*lbf)

HINT:

Turn the bolt while holding the nut.



Hide 12313 5.INSTALL ENGINE MOVING CONTROL ROD BRACKET

a.
C235553C01
1.115,0.427 1.635,0.635 0.521,0.208 10 true 1 (*a), 5 0.729,1.792 0.854,1.979 0.125,0.188 10 false 2 2.135,1.74 2.26,1.927 0.125,0.188 10 true 3 2.792,1.073 2.917,1.26 0.125,0.188 10 true 4
*a Temporarily Tighten


Install the engine moving control rod bracket to the manual transaxle assembly with the 4 bolts in the order shown in the illustration.

Torque:
45 N*m (459 kgf*cm, 33 ft.*lbf)


Hide 12321B 6.INSTALL DRIVE SHAFT HEAT INSULATOR SUB-ASSEMBLY

a.

Install the drive shaft heat insulator sub-assembly to the engine assembly with the bolt.

Torque:
17.6 N*m (179 kgf*cm, 13 ft.*lbf)


b.

Using a 12 mm deep socket wrench, install the nut.

Torque:
17.6 N*m (179 kgf*cm, 13 ft.*lbf)


Hide 51201 7.INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

Hide 28100 8.INSTALL STARTER ASSEMBLY

Hide 17410 10.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 57533B 11.INSTALL FRONT FLOOR CENTER BRACE

Hide 58910C 12.INSTALL REAR CONSOLE BOX ASSEMBLY (w/ Console Box Lid)

Hide 58910C 13.INSTALL REAR CONSOLE BOX ASSEMBLY (w/o Console Box Lid)

Hide 31470 14.INSTALL CLUTCH RELEASE CYLINDER ASSEMBLY

a.
C283169E01
1.906,0.615 2.042,0.792 0.135,0.177 10 true A 2.406,0.479 2.542,0.656 0.135,0.177 10 true A 0.448,0.563 0.583,0.74 0.135,0.177 10 true B 1.115,0.708 1.25,0.885 0.135,0.177 10 true B

Install the clutch release cylinder assembly to the manual transaxle assembly with the 2 bolts B.

Torque:
11.8 N*m (120 kgf*cm, 9 ft.*lbf)


b.

Install the clutch release cylinder to flexible hose tube to the manual transaxle assembly with the 2 bolts A and a new clip.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 33524B 15.INSTALL CONTROL CABLE BRACKET

a.

Install the control cable bracket to the manual transaxle assembly with the 2 bolts.

Torque:
24.5 N*m (250 kgf*cm, 18 ft.*lbf)


b.

Install the wire harness clamp bracket to the control cable bracket with the bolt.

Torque:
12.8 N*m (131 kgf*cm, 9 ft.*lbf)


Hide 82121 16.CONNECT ENGINE WIRE (w/ ABS)

a.

Engage the 2 clamps to install the engine wire to the wire harness clamp brackets.


b.

Install the engine wire to the wire harness clamp bracket with the bolt.

Torque:
12.8 N*m (131 kgf*cm, 9 ft.*lbf)


c.

Connect the connector to the manual transaxle assembly.


Hide 82121 17.CONNECT ENGINE WIRE (w/o ABS)

a.

Engage the 2 clamps to install the engine wire to the wire harness clamp brackets.


b.

Install the engine wire to the wire harness clamp bracket with the bolt.

Torque:
12.8 N*m (131 kgf*cm, 9 ft.*lbf)


c.

Connect the 2 connectors to the manual transaxle assembly.


Hide 82123 18.CONNECT NO. 3 ENGINE WIRE

a.

Engage the 2 clamps to install the No. 3 engine wire to the engine mounting bracket LH.


b.

Connect the No. 3 engine wire to the manual transaxle assembly with the bolt.

Torque:
25.5 N*m (260 kgf*cm, 19 ft.*lbf)


Hide 33820B 19.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.
C283113C01
2.188,0.406 3.031,0.656 3.031,0.656 2.552,0.708 true 0.177,0.875 0.313,1.052 0.135,0.177 10 true A 2.063,1.583 2.198,1.76 0.135,0.177 10 true A 1.667,0.01 1.802,0.188 0.135,0.177 10 true B 2.771,1.063 2.906,1.24 0.135,0.177 10 true B 3.063,0.573 3.375,0.729 0.313,0.156 10 false *a
*a Paint Mark


Install the transmission control cable assembly to the control cable bracket with 2 new clips B.

NOTICE:

Make sure that the paint marks on the transmission control cable assembly are aligned with the slits in the control cable bracket before installing the clips.



b.

Connect the transmission control cable assembly to the floor shift selecting bellcrank assembly with the 2 washers and 2 clips A.


Hide 17801 24.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 17735 25.INSTALL AIR CLEANER CAP WITH NO. 1 AIR CLEANER HOSE

Hide 23820 26.CONNECT FUEL VAPOR FEED HOSE ASSEMBLY

Hide 23827A 27.CONNECT NO. 2 FUEL VAPOR FEED HOSE

Hide 28.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 31.INSPECT FOR MANUAL TRANSAXLE OIL LEAK

Hide 32.INSPECT FOR EXHAUST GAS LEAK

Hide 51441C 33.INSTALL ENGINE UNDER COVER RH (w/o Metal Type Under Cover)

Hide 51442C 34.INSTALL ENGINE UNDER COVER LH (w/o Metal Type Under Cover)

Hide 51405A 35.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY (w/ Metal Type Under Cover)

Hide 51451A 36.INSTALL CENTER ENGINE UNDER COVER (w/ Metal Type Under Cover)