Home › Drivetrain › K312 CVT › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › 2016.07–2017.10
RM30M0E _52 Drivetrain _052969 K312 CVT _0256556 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K312 CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P0741  Torque Converter Clutch Solenoid Performance (Shift Solenoid Valve SL)  P075B  Shift Solenoid "G" Performance or Stuck Off  P2757  Torque Converter Clutch Pressure Control Solenoid Performance (Shift Solenoid Valve SLU)  


DESCRIPTION

The ECM uses the shift solenoid valves SC and SL to switch control of the shift solenoid valve SLU between forward and reverse clutch control and lock-up control in response to driving conditions.

HINT:

If DTC P0741 is stored after the engine has stalled, the lock-up shift solenoid valve (shift solenoid valve SL) may be malfunctioning.


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0741 Torque Converter Clutch Solenoid Performance (Shift Solenoid Valve SL) One of the following conditions is met (2 trip detection logic):
·

When the ECM sends a lock-up OFF command and turns the shift solenoid valves SC and SL OFF, the difference between the engine speed (NE) and input turbine speed (NT) is 25 rpm or less for 1 second or more.

·

When the ECM turns the shift solenoid valves SC and SL ON, the difference between the input turbine speed (NT) and primary pulley speed (NIN) is 300 rpm or more for 1 second or more.

·

While the vehicle is driven, a lock-up ON command is sent, but lock-up control is not performed for 1 second or more.


·

Torque converter assembly

·

Continuously variable transaxle assembly


Comes on DTC stored
P075B Shift Solenoid "G" Performance or Stuck Off One of the following conditions is met (2 trip detection logic):
·

When the ECM sends a lock-up ON command and turns the shift solenoid valves SC and SL ON, the difference between the engine speed (NE) and input turbine speed (NT) is 25 rpm or less for 1 second or more.

·

When the ECM turns the shift solenoid valves SC and SL OFF, the difference between the input turbine speed (NT) and primary pulley speed (NIN) is 300 rpm or more for 1 second or more.

·

While the vehicle is driven, a lock-up ON command is sent, but lock-up control is not performed for 1 second or more.


·

Torque converter assembly

·

Continuously variable transaxle assembly


Comes on DTC stored
P2757 Torque Converter Clutch Pressure Control Solenoid Performance (Shift Solenoid Valve SLU) One of the following conditions is met (2 trip detection logic):
·

When the ECM sends a lock-up ON command and turns the shift solenoid valves SC and SLU OFF and SL ON, the difference between the engine speed (NE) and input turbine speed (NT) is 25 rpm or less for 1 second or more.

·

While the vehicle is driven, a lock-up signal is turned ON, but the lock-up remains OFF for 1 second or more.


·

Torque converter assembly

·

Continuously variable transaxle assembly


Comes on DTC stored

MONITOR DESCRIPTION

When performing lock-up control (on/off) of the torque converter, the ECM compares the transmission revolution sensor (NT) output speed and engine speed (NE) to detect mechanical malfunctions in the shift solenoid valves SL and SC.

If the torque converter does not lock-up while a lock-up ON command is being sent, the ECM detects it as a mechanical malfunction of the shift solenoid valve SLU.

If the difference between the engine speed (NE) and transmission revolution sensor (NT) output speed or transmission revolution sensor (NIN) output speed and transmission revolution sensor (NT) output speed is outside of the threshold, the ECM detects the malfunction, illuminates the MIL and stores a DTC.

CAUTION / NOTICE / HINT

NOTICE:
·

Perform initialization after replacing any parts related to the continuously variable transaxle system.

Click hereDrivetrain>K312 CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION


·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K312 CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.CHECK DTC OUTPUT (IN ADDITION TO DTC P0741, P075B AND P2757)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

e.

Read the DTCs using the GTS.

HINT:

If any DTCs other than P0741, P075B or P2757 are output, perform troubleshooting for those DTCs first.



Result:
Result Proceed to
Only DTC P0741, P075B and/or P2757 is output A
DTC P0741, P075B and/or P2757 and other DTCs are output B



A

2.CLEAR DTC

B

2.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234
Result:
Proceed to
NEXT




NEXT

3.PERFORM DRIVE TEST
3.PERFORM DRIVE TEST
CAUTION:

Strictly observe posted speed limits, traffic laws and road conditions when performing a road test.


NOTICE:
·

This test must be performed after checking and confirming that the engine is normal.

·

Perform this test with the CVT fluid temperature between 50 and 100°C (122 and 212°F).

·

Perform the test with the air conditioning off.



HINT:
·

Lock-up control will not operate when the CVT fluid temperature is 40°C (104°F) or less and the vehicle speed is 60 km/h (37 mph) or less, or when the CVT fluid temperature is 5°C (41°F) or less.

·

Lock-up control will not operate when the engine coolant temperature is 30°C (86°F) or less.

·

The lock-up OFF vehicle speed may vary depending on the electrical load, and air conditioning and brake operations.



a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed, SPD (NT), SPD (NIN), Lock Up, SL Solenoid Status and Solenoid (SC).

Powertrain > Engine and ECT > Data List
Tester Display
Engine Speed
SPD (NT)
SPD (NIN)
Lock Up
SL Solenoid Status
Solenoid(SC)
50003 234 9,390,400,417,419,1002

e.

According to the display on the GTS, read the Data List while driving.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Engine Speed Engine speed Min.: 0 rpm
Max.: 16383 rpm
680 to 780 rpm: Idling with warm engine, shift lever in N, A/C off When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed.
SPD (NT) Input turbine speed (NT) Min.: 0 rpm
Max.: 12750 rpm
·

Input turbine speed (NT) equal to engine speed (NE): Lock-up ON (After warming up engine)

·

Input turbine speed (NT) nearly equal to engine speed (NE): Lock-up OFF (Idling with shift lever in P or N)

·

0 rpm: Vehicle stopped with shift lever in D


Data is displayed in increments of 50 rpm.
SPD (NIN) Primary pulley speed (NIN) Min.: 0 rpm
Max.: 12750 rpm
·

0 rpm: Vehicle stopped

·

Primary pulley speed (NIN) equal to engine speed (NE): Lock-up ON (After warming up engine)


Data is displayed in increments of 50 rpm.
Lock Up Lock-up OFF or ON
·

ON: Lock-up operating

·

OFF: Lock-up not operating


-
SL Solenoid Status Shift solenoid valve SL status OFF or ON
·

ON: Lock-up permitted

·

OFF: Lock-up not permitted


-
Solenoid(SC) Shift solenoid valve SC status OFF or ON
·

ON: For 1 second after moving shift lever from P to D or R, or N to D or R

·

ON: Lock-up ON to OFF

·

OFF: Engine idling


-

Result:
Result Proceed to
When Lock Up is ON, the input turbine speed (NT) is lower than the engine speed (NE). A
When the shift solenoid valves SC and SL are OFF, the input turbine speed (NT) is equal to the engine speed (NE).
When the shift solenoid valves SC and SL are ON, there is a large difference between the input turbine speed (NT) and the primary pulley speed (NIN).
When Lock Up is ON, the input turbine speed (NT) is equal to the engine speed (NE). B
When the shift solenoid valves SC and SL are OFF, the input turbine speed (NT) is lower than the engine speed (NE).
When the shift solenoid valves SC and SL are ON, the input turbine speed (NT) is equal to the primary pulley speed (NIN).



A

4.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

B

4.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
a.

Replace the continuously variable transaxle assembly and torque converter assembly.

Click hereDrivetrain>K312 CVT>CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY>COMPONENTS


Result:
Proceed to
NEXT



NEXT