Home › Drivetrain › K312 CVT › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › 2016.07–2017.10
RM30M0E _52 Drivetrain _052969 K312 CVT _0256556 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K312 CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P0841  Transmission Fluid Pressure Sensor "A" Performance  P2829  Pressure Control Solenoid "K" Performance (Shift Solenoid Valve SLS)  


DESCRIPTION

The ECM controls the secondary oil pressure based on the secondary oil pressure signal output by the oil pressure sensor.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0841 Transmission Fluid Pressure Sensor "A" Performance Either one of the following conditions is met (1 trip detection logic):
·

When the requested oil pressure is 1.4 MPa (14.3 kgf/cm2, 203 psi) or more, the oil pressure sensor output is 0.5 MPa (5.1 kgf/cm2, 73 psi) or less for 2 seconds or more.

·

When the requested oil pressure is 1.0 MPa (10.2 kgf/cm2, 145 psi) or less, the difference between the calculated primary pulley pressure and target primary pulley pressure is 2.5 MPa (25.5 kgf/cm2, 363 psi) or more for 3 seconds or more.


·

Oil pressure sensor

·

ECM


Comes on DTC stored
P2829 Pressure Control Solenoid "K" Performance (Shift Solenoid Valve SLS) One of the following conditions is met (1 trip detection logic):
·

When the requested oil pressure is 1.0 MPa (10.2 kgf/cm2, 145 psi) or less, the oil pressure sensor output is 2.5 MPa (25.5 kgf/cm2, 363 psi) or more for 3 seconds or more.

·

When the vehicle speed is less than 8 km/h (5 mph), the ratio of the transmission revolution sensor (NIN) output speed and transmission revolution sensor (NOUT) output speed exceeds a specified value for 0.2 seconds or more.

·

When the oil pressure sensor output is less than 0.35 MPa (3.6 kgf/cm2, 51 psi) and the target gear ratio is 2.0 or more, the actual gear ratio is less than 1.0 for 1.5 seconds or more.


·

Continuously variable transaxle assembly

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

The ECM checks for belt clamping high-pressure or low-pressure malfunctions. If a mechanical malfunction of the shift solenoid valve SLS or the oil pressure sensor is detected by the ECM, it illuminates the MIL and stores a DTC.

CAUTION / NOTICE / HINT

NOTICE:
·

Perform initialization after replacing any parts related to the continuously variable transaxle system.

Click hereDrivetrain>K312 CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION


·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K312 CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.CHECK DTC OUTPUT (IN ADDITION TO DTC P0841 AND P2829)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

e.

Read the DTCs using the GTS.

HINT:

If any DTCs other than P0841 or P2829 are output, perform troubleshooting for those DTCs first.



Result:
Result Proceed to
Both DTC P0841 and P2829 are output A
Only DTC P0841 is output B
Only DTC P2829 is output C
DTC P0841 and/or P2829 and other DTCs are output D



A

2.READ VALUE USING GTS (A/T OIL PRESSURE)

B

13.READ VALUE USING GTS (A/T OIL PRESSURE)

C

20.READ VALUE USING GTS (A/T OIL PRESSURE)

D

2.READ VALUE USING GTS (A/T OIL PRESSURE)
CAUTION:
·

Do not perform a stall test if there are any people or objects near the vehicle.

·

Do not perform a stall test if any wheel chocks are out of position.

·

Do not perform the stall test on a slippery or low-friction surface that could allow the tires to spin.



NOTICE:
·

This test must be performed after checking and confirming that the engine is normal.

·

Perform this test with the CVT fluid temperature between 50 and 100°C (122 and 212°F).

·

Perform this test with the air conditioning off.

·

Do not perform the stall speed test for longer than 5 seconds

·

When performing the stall speed test more than once, make sure to wait 15 seconds or more between tests.



a.

Warm up the engine.


b.

Fully apply the parking brake and chock all 4 wheels.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Connect the TC and TE1.

Powertrain > Engine and ECT > Active Test
Active Test Display
Connect the TC and TE1
Data List Display
A/T Oil Pressure
50004 234 13 409

g.

Observe "A/T Oil Pressure" in the Data List.


h.

According to the display on the GTS, read the Data List.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
A/T Oil Pressure Secondary oil pressure value Min.: -64 MPa
Max.: 63.998 MPa
Secondary oil pressure inspection:
·

4.2 to 4.9 MPa (42.8 to 50.0 kgf/cm2, 609 to 711 psi): D position stall test

·

4.0 to 5.1 MPa (40.8 to 52.0 kgf/cm2, 580 to 740 psi): R position stall test


-

Result:
Result Proceed to
Data List value is normal A
Data List value is not normal B



A

3.REPLACE ECM

B

4.REPLACE OIL PRESSURE SENSOR
3.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

4.REPLACE OIL PRESSURE SENSOR
a.

Replace the oil pressure sensor.

Click hereDrivetrain>K312 CVT>OIL PRESSURE SENSOR>COMPONENTS


Result:
Proceed to
NEXT



NEXT

5.CLEAR DTC
5.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234
Result:
Proceed to
NEXT




NEXT

6.PERFORM INITIALIZATION
6.PERFORM INITIALIZATION
NOTICE:
·

Performing Reset Memory will clear the learned values of the yaw rate and acceleration sensor (Deceleration Sensor Zero Point Calibration) and the CVT oil pressure (CVT Oil Pressure Calibration). Make sure to perform Reset Memory, Deceleration Sensor Zero Point Calibration, and CVT Oil Pressure Calibration if any of the parts in the following table have been replaced.

Replaced Part
·

Continuously variable transaxle assembly

·

ECM

·

Oil pressure sensor

·

Airbag ECU assembly (Yaw rate and acceleration sensor)*1

·

Brake actuator assembly (Skid control ECU)*2

·

Deceleration sensor assembly*2



·

After performing Reset Memory, always perform Deceleration Sensor Zero Point Calibration first, and then CVT Oil Pressure Calibration.

·

Always perform calibration with the vehicle on level ground (Inclination: 0 +/- 0.25°).

·

Do not shake or vibrate the vehicle during calibration.

*1: w/ VSC

*2: w/o VSC




a.

Using the GTS, perform Reset Memory, Deceleration Sensor Zero Point Calibration and CVT Oil Pressure Calibration.

Click hereDrivetrain>K312 CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

7.CHECK DTC OUTPUT
7.CHECK DTC OUTPUT

b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

f.

Read the DTCs using the GTS.


Result:
Result Proceed to
DTC P0841 and/or P2829 is output A
DTC is not output B



A

8.REPLACE ECM

B

END

8.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

9.PERFORM INITIALIZATION
9.PERFORM INITIALIZATION
NOTICE:
·

Performing Reset Memory will clear the learned values of the yaw rate and acceleration sensor (Deceleration Sensor Zero Point Calibration) and the CVT oil pressure (CVT Oil Pressure Calibration). Make sure to perform Reset Memory, Deceleration Sensor Zero Point Calibration, and CVT Oil Pressure Calibration if any of the parts in the following table have been replaced.

Replaced Part
·

Continuously variable transaxle assembly

·

ECM

·

Oil pressure sensor

·

Airbag ECU assembly (Yaw rate and acceleration sensor)*1

·

Brake actuator assembly (Skid control ECU)*2

·

Deceleration sensor assembly*2



·

After performing Reset Memory, always perform Deceleration Sensor Zero Point Calibration first, and then CVT Oil Pressure Calibration.

·

Always perform calibration with the vehicle on level ground (Inclination: 0 +/- 0.25°).

·

Do not shake or vibrate the vehicle during calibration.

*1: w/ VSC

*2: w/o VSC




a.

Using the GTS, perform Reset Memory, Deceleration Sensor Zero Point Calibration and CVT Oil Pressure Calibration.

Click hereDrivetrain>K312 CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

10.CHECK DTC OUTPUT
10.CHECK DTC OUTPUT

b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

f.

Read the DTCs using the GTS.


Result:
Result Proceed to
DTC P2829 is output A
DTC is not output B



A

11.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

B

END

11.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
a.

Replace the continuously variable transaxle assembly.

Click hereDrivetrain>K312 CVT>CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY>COMPONENTS


Result:
Proceed to
NEXT



NEXT

12.CLEAR DTC
12.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234
Result:
Proceed to
NEXT




NEXT

13.READ VALUE USING GTS (A/T OIL PRESSURE)
CAUTION:
·

Do not perform a stall test if there are any people or objects near the vehicle.

·

Do not perform a stall test if any wheel chocks are out of position.

·

Do not perform the stall test on a slippery or low-friction surface that could allow the tires to spin.



NOTICE:
·

This test must be performed after checking and confirming that the engine is normal.

·

Perform this test with the CVT fluid temperature between 50 and 100°C (122 and 212°F).

·

Perform this test with the air conditioning off.

·

Do not perform the stall speed test for longer than 5 seconds

·

When performing the stall speed test more than once, make sure to wait 15 seconds or more between tests.



a.

Warm up the engine.


b.

Fully apply the parking brake and chock all 4 wheels.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Connect the TC and TE1.

Powertrain > Engine and ECT > Active Test
Active Test Display
Connect the TC and TE1
Data List Display
A/T Oil Pressure
50004 234 13 409

g.

Observe "A/T Oil Pressure" in the Data List.


h.

According to the display on the GTS, read the Data List.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
A/T Oil Pressure Secondary oil pressure value Min.: -64 MPa
Max.: 63.998 MPa
Secondary oil pressure inspection:
·

4.2 to 4.9 MPa (42.8 to 50.0 kgf/cm2, 609 to 711 psi): D position stall test

·

4.0 to 5.1 MPa (40.8 to 52.0 kgf/cm2, 580 to 740 psi): R position stall test


-

Result:
Result Proceed to
Data List value is not normal A
Data List value is normal B



A

14.REPLACE OIL PRESSURE SENSOR

B

19.REPLACE ECM
14.REPLACE OIL PRESSURE SENSOR
a.

Replace the oil pressure sensor.

Click hereDrivetrain>K312 CVT>OIL PRESSURE SENSOR>COMPONENTS


Result:
Proceed to
NEXT



NEXT

15.CLEAR DTC
15.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234
Result:
Proceed to
NEXT




NEXT

16.PERFORM INITIALIZATION
16.PERFORM INITIALIZATION
NOTICE:
·

Performing Reset Memory will clear the learned values of the yaw rate and acceleration sensor (Deceleration Sensor Zero Point Calibration) and the CVT oil pressure (CVT Oil Pressure Calibration). Make sure to perform Reset Memory, Deceleration Sensor Zero Point Calibration, and CVT Oil Pressure Calibration if any of the parts in the following table have been replaced.

Replaced Part
·

Continuously variable transaxle assembly

·

ECM

·

Oil pressure sensor

·

Airbag ECU assembly (Yaw rate and acceleration sensor)*1

·

Brake actuator assembly (Skid control ECU)*2

·

Deceleration sensor assembly*2



·

After performing Reset Memory, always perform Deceleration Sensor Zero Point Calibration first, and then CVT Oil Pressure Calibration.

·

Always perform calibration with the vehicle on level ground (Inclination: 0 +/- 0.25°).

·

Do not shake or vibrate the vehicle during calibration.

*1: w/ VSC

*2: w/o VSC




a.

Using the GTS, perform Reset Memory, Deceleration Sensor Zero Point Calibration and CVT Oil Pressure Calibration.

Click hereDrivetrain>K312 CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

17.CHECK DTC OUTPUT
17.CHECK DTC OUTPUT

b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

f.

Read the DTCs using the GTS.


Result:
Result Proceed to
DTC P0841 is output A
DTC is not output B



A

18.REPLACE ECM

B

END

18.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

19.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

20.READ VALUE USING GTS (A/T OIL PRESSURE)
CAUTION:
·

Do not perform a stall test if there are any people or objects near the vehicle.

·

Do not perform a stall test if any wheel chocks are out of position.

·

Do not perform the stall test on a slippery or low-friction surface that could allow the tires to spin.



NOTICE:
·

This test must be performed after checking and confirming that the engine is normal.

·

Perform this test with the CVT fluid temperature between 50 and 100°C (122 and 212°F).

·

Perform this test with the air conditioning off.

·

Do not perform the stall speed test for longer than 5 seconds

·

When performing the stall speed test more than once, make sure to wait 15 seconds or more between tests.



a.

Warm up the engine.


b.

Fully apply the parking brake and chock all 4 wheels.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Connect the TC and TE1.

Powertrain > Engine and ECT > Active Test
Active Test Display
Connect the TC and TE1
Data List Display
A/T Oil Pressure
50004 234 13 409

g.

Observe "A/T Oil Pressure" in the Data List.


h.

According to the display on the GTS, read the Data List.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
A/T Oil Pressure Secondary oil pressure value Min.: -64 MPa
Max.: 63.998 MPa
Secondary oil pressure inspection:
·

4.2 to 4.9 MPa (42.8 to 50.0 kgf/cm2, 609 to 711 psi): D position stall test

·

4.0 to 5.1 MPa (40.8 to 52.0 kgf/cm2, 580 to 740 psi): R position stall test


-

Result:
Result Proceed to
Data List value is normal A
Data List value is not normal B



A

21.REPLACE ECM

B

22.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
21.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

22.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
a.

Replace the continuously variable transaxle assembly.

Click hereDrivetrain>K312 CVT>CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY>COMPONENTS


Result:
Proceed to
NEXT



NEXT