Home › Engine / Hybrid System › 2NZ-FE INTAKE / EXHAUST › EXHAUST PIPE › 2016.07–2016.10
RM30M0E _51 Engine / Hybrid System _017080 2NZ-FE INTAKE / EXHAUST _0091237 EXHAUST PIPE A

2NZ-FE INTAKE / EXHAUST  EXHAUST PIPE  INSTALLATION  


PROCEDURE

Hide 17410 1.INSTALL FRONT EXHAUST PIPE ASSEMBLY

a.
A128853

Using a vernier caliper, measure the free length of the compression spring.

Free Length of Compression Spring:
Standard Length Minimum Length
42 mm (1.65 in.) 40.5 mm (1.59 in.)


If the length is not as specified, replace the compression spring.


b.
A171211C01
0.927,1.875 0.927,1.438 false 1.604,1.927 1.604,1.573 false 1.823,0.635 2,0.385 false 2.469,0.99 2.646,0.74 false 0.865,1.885 1.177,2.042 0.313,0.156 10 false *1 1.552,1.927 1.865,2.083 0.313,0.156 10 false *2 2.021,0.281 2.333,0.438 0.313,0.156 10 false *a 2.656,0.646 2.969,0.802 0.313,0.156 10 false *b
*1 Exhaust Manifold
*2 Exhaust Pipe Gasket
*a Wooden Block
*b Plastic Hammer


Using a plastic hammer and a wooden block, tap in a new exhaust pipe gasket until its surface is flush with the exhaust manifold.

NOTICE:
·

Install the exhaust pipe gasket in the correct direction.

·

Do not reuse the exhaust pipe gasket.

·

Do not damage the exhaust pipe gasket by dropping it, etc.

·

Do not damage the outer surface of the exhaust pipe gasket.

·

Do not push in the exhaust pipe gasket with the front exhaust pipe assembly when connecting it.




c.

Connect the 3 exhaust pipe supports to install the front exhaust pipe assembly to the vehicle.


d.
A247549C10
0.323,0.375 0.552,0.594 false 0.521,0.896 0.323,1.104 false 2.115,1.229 1.958,0.927 true 0.146,0.281 0.313,0.448 0.167,0.167 10 false *1 0.146,1.031 0.313,1.198 0.167,0.167 10 false *2 2.042,1.229 2.208,1.396 0.167,0.167 10 false *3 2.771,1.323 2.938,1.49 0.167,0.167 10 false *a
*1 Exhaust Manifold
*2 Front Exhaust Pipe Assembly
*3 Exhaust Pipe Gasket
*a Space between flanges: 8.5 mm (0.335 in.)


Install the front exhaust pipe assembly to the exhaust manifold with the 2 compression springs and 2 bolts.

Torque:

43 N*m (440 kgf*cm, 32 ft.*lbf)


NOTICE:

After the installation, check that the gaps between the flanges of the exhaust manifold and front exhaust pipe assembly are consistent front-to-rear and left-to-right.



Hide 17430 2.INSTALL TAIL EXHAUST PIPE ASSEMBLY

a.
A128853

Using a vernier caliper, measure the free length of the compression spring.

Free Length of Compression Spring:
Standard Length Minimum Length
40 mm (1.57 in.) 38.5 mm (1.52 in.)


If the length is not as specified, replace the compression spring.


b.
A171211C01
0.927,1.875 0.927,1.438 false 1.604,1.927 1.604,1.573 false 1.823,0.635 2,0.385 false 2.469,0.99 2.646,0.74 false 0.865,1.885 1.177,2.042 0.313,0.156 10 false *1 1.552,1.927 1.865,2.083 0.313,0.156 10 false *2 2.021,0.281 2.333,0.438 0.313,0.156 10 false *a 2.656,0.646 2.969,0.802 0.313,0.156 10 false *b
*1 Front Exhaust Pipe Assembly
*2 Exhaust Pipe Gasket
*a Wooden Block
*b Plastic Hammer


Using a plastic hammer and a wooden block, tap in a new exhaust pipe gasket until its surface is flush with the front exhaust pipe assembly.

NOTICE:
·

Install the exhaust pipe gasket in the correct direction.

·

Do not reuse the exhaust pipe gasket.

·

Do not damage the exhaust pipe gasket by dropping it, etc.

·

Do not damage the outer surface of the exhaust pipe gasket.

·

Do not push in the exhaust pipe gasket with the tail exhaust pipe assembly when connecting it.




c.

Connect the 3 exhaust pipe supports to install the tail exhaust pipe assembly to the vehicle.


d.
A247551C04
2.625,1.104 2.854,0.906 false 2.656,1.281 2.875,1.51 false 1.448,1.323 1.24,1.792 true 2.885,0.813 3.063,0.979 0.177,0.167 10 false *1 2.906,1.438 3.083,1.604 0.177,0.167 10 false *2 1.177,1.802 1.354,1.969 0.177,0.167 10 false *3 0.479,0.583 0.656,0.75 0.177,0.167 10 false *a
*1 Front Exhaust Pipe Assembly
*2 Tail Exhaust Pipe Assembly
*3 Exhaust Pipe Gasket
*a Space between flanges: 6.5 mm (0.256 in.)


Install the tail exhaust pipe assembly to the front exhaust pipe assembly with the 2 compression springs and 2 bolts.

Torque:

43 N*m (440 kgf*cm, 32 ft.*lbf)


NOTICE:

After the installation, check that the gaps between the flanges of the tail exhaust pipe assembly and front exhaust pipe assembly are consistent front-to-rear and left-to-right.



Hide 57533B 3.INSTALL FRONT FLOOR CENTER BRACE

Hide 89465A 4.INSTALL HEATED OXYGEN SENSOR (for Sensor 2)

Hide 5.INSPECT FOR EXHAUST GAS LEAK