Home › Engine / Hybrid System › 1NR-FE FUEL › FUEL TANK(for TMT Made) › 2016.07–2017.10
RM30M0E _51 Engine / Hybrid System _053554 1NR-FE FUEL _0259938 FUEL TANK(for TMT Made) A

1NR-FE FUEL  FUEL TANK(for TMT Made)  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

a.
A250068C06
1.906,0.75 2.208,0.302 false 2.24,0.188 2.438,0.365 0.198,0.177 10 false *a
*a Cord


When removing and storing the fuel tank assembly, arrange the inlet hose as shown in the illustration, and secure the fuel tank assembly using a cord or similar.

NOTICE:

Depending on the arrangement of the inlet hose during storage, the inlet hose and rear suspension may interfere and cause fuel leakage.



Hide 77020A 2.REMOVE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

Hide 3.DRAIN FUEL

Hide 77310A 4.REMOVE FUEL TANK CAP ASSEMBLY

Hide 5.REMOVE REAR WHEEL LH

Hide 57533B 6.REMOVE FRONT FLOOR CENTER BRACE

Hide 51451A 7.REMOVE CENTER ENGINE UNDER COVER (w/ Metal Type Under Cover)

Hide 51405A 8.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY (w/ Metal Type Under Cover)

Hide 17410 9.REMOVE FRONT EXHAUST PIPE ASSEMBLY (for Sedan)

a.
A384685C03
0.156,0.167 0.406,0.375 0.25,0.208 12 true *A 0.125,2.5 0.396,2.719 0.271,0.219 12 true *B
*A for CVT
*B for Manual Transaxle


Disconnect the heated oxygen sensor connector.


b.

Disengage the clamp to disconnect the heated oxygen sensor wire from the wire harness clamp bracket.


c.
A304876

Remove the 2 bolts and 2 compression springs to separate the front exhaust pipe assembly from the exhaust manifold converter sub-assembly.


d.

w/ Compression Spring:

i.

Remove the 2 bolts and 2 compression springs to separate the front exhaust pipe assembly from the tail exhaust pipe assembly.



e.

w/o Compression Spring:

i.

Remove the 2 bolts to separate the front exhaust pipe assembly from the tail exhaust pipe assembly.



f.

Disconnect the 3 exhaust pipe supports to remove the front exhaust pipe assembly from the vehicle.


g.

Remove the 2 exhaust pipe gaskets from the exhaust manifold converter sub-assembly and front exhaust pipe assembly.


Hide 10.REMOVE FRONT EXHAUST PIPE ASSEMBLY (for Hatchback)

a.
A384685C02
0.156,0.167 0.406,0.375 0.25,0.208 12 true *A 0.125,2.5 0.396,2.719 0.271,0.219 12 true *B
*A for CVT
*B for Manual Transaxle


Disconnect the heated oxygen sensor connector.


b.

Disengage the clamp to disconnect the heated oxygen sensor wire from the wire harness clamp bracket.


c.
A304876

Remove the 2 bolts and 2 compression springs to separate the front exhaust pipe assembly from the exhaust manifold converter sub-assembly.


d.

Remove the 2 bolts and 2 compression springs to separate the front exhaust pipe assembly from the tail exhaust pipe assembly.


e.

Disconnect the 3 exhaust pipe supports to remove the front exhaust pipe assembly from the vehicle.


f.

Remove the 2 exhaust pipe gaskets from the exhaust manifold converter sub-assembly and front exhaust pipe assembly.


Hide 58156 11.REMOVE FRONT NO. 4 FLOOR HEAT INSULATOR

a.
A300030

Remove the 2 nuts and front No. 4 floor heat insulator from the vehicle.


Hide 77641A 12.REMOVE NO. 1 FUEL TANK PROTECTOR

a.
A305619

Remove the bolt, clip and No. 1 fuel tank protector from the vehicle.


Hide 46420 13.SEPARATE NO. 2 PARKING BRAKE CABLE ASSEMBLY

a.
A300032

Remove the 2 bolts to separate the No. 2 parking brake cable assembly from the vehicle.


Hide 77028F 14.DISCONNECT NO. 2 FUEL EMISSION TUBE SUB-ASSEMBLY

a.
A300033

Slide the hose clip and disconnect the No. 2 fuel emission tube sub-assembly from the fuel tank to canister tube.


Hide 77209F 15.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.
A313096C01
2.552,2.521 2.729,2.271 false 0.969,2.479 0.76,2.25 false 2.115,2.531 1.906,2.302 false 2.208,4.083 2.385,3.833 true 1.177,3.76 0.969,3.531 false 2.333,4.5 2.615,4.5 false 2.375,4.365 2.625,4.198 false 1.677,4.135 1.906,3.771 1.906,3.771 1.823,4.146 true 2.781,2.177 3.094,2.333 0.313,0.156 10 false *1 0.573,2.177 0.885,2.333 0.313,0.156 10 false *2 2.656,4.438 2.969,4.594 0.313,0.156 10 false *3 2.698,4.104 3.01,4.26 0.313,0.156 10 false *4 0.792,3.438 1.104,3.594 0.313,0.156 10 false *5 1.969,3.667 2.281,3.823 0.313,0.156 10 false *6 1.729,2.167 2.042,2.323 0.313,0.156 10 false *1 2.438,3.771 2.75,3.927 0.313,0.156 10 false *1
*1 Retainer
*2 Fuel Tube Connector Cover
*3 Fuel Tube Connector
*4 Fuel Pipe
*5 Nylon Tube
*6 O-ring
V100135

Pull
V100136

Pinch
V100137

Pull Out


Release the lock of the fuel tube connector cover as shown in the illustration, then pull out the fuel tank main tube sub-assembly.

NOTICE:
·

If the fuel tube connector and fuel main tube are stuck together, push in and pull out the fuel tube connector while squeezing the fuel main tube to release the connection, and then disconnect the fuel tube connector.

·

Clean away any dirt or foreign matter from the fuel tube connector before performing the operation.

·

The fuel tube connector and fuel main tube are sealed by O-ring, so be careful to prevent damage to and foreign matter sticking to the contact surfaces.

·

Do not use any tools.

·

After disconnecting the fuel tube connector, check that there is no foreign matter on the seal surface of the fuel main tube.

·

After disconnecting the fuel tank main tube sub-assembly, protect the contact surfaces by covering them with a plastic bag.

·

Do not bend or twist the tubes.




Hide 77100 16.REMOVE FUEL TANK ASSEMBLY

A305588

a.

Disengage the 2 clamps to separate the No. 6 fuel tank breather tube.


b.

Remove the bolt to separate the fuel tank filler pipe flange plate from the vehicle.


c.

Disengage the clamp to remove the fuel tank filler pipe flange plate from the No. 3 fuel tank filler pipe support.


d.
A247508C03
2.5,1.5 2.833,1.333 false 0.417,0.583 1.333,0.917 true 0.229,0.479 0.542,0.635 0.313,0.156 10 false *1 2.844,1.229 3.156,1.385 0.313,0.156 10 false *2
*1 Fuel Tank Filler Pipe Sub-assembly
*2 No. 1 Fuel Tank Breather Tube


Separate the fuel tank filler pipe sub-assembly and No. 1 fuel tank breather tube from the No. 3 fuel tank filler pipe support.


e.

Using an engine lifter, support the fuel tank assembly.


f.
A300037

Remove the 4 bolts and fuel tank assembly from the vehicle.

NOTICE:

Make sure that the fuel tank assembly does not fall.



Hide 77209F 17.REMOVE FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.
A300035

Disengage the 2 clamps to remove the fuel tank main tube sub-assembly from the fuel tank assembly.


Hide 77028F 18.REMOVE NO. 2 FUEL EMISSION TUBE SUB-ASSEMBLY

a.
A300036

Disengage the 2 clamps to remove the No. 2 fuel emission tube sub-assembly from the fuel tank assembly.


Hide 77701W 19.REMOVE NO. 1 CANISTER OUTLET HOSE SUB-ASSEMBLY

a.
A305606C02
1.917,0.219 2.51,0.125 false 1.75,0.146 2.063,0.302 0.313,0.156 10 false *1
*1 No. 6 Fuel Tank Breather Tube


Disengage the 2 clamps to remove the No. 1 canister outlet hose sub-assembly from the fuel tank assembly.


b.

Disconnect the No. 1 canister outlet hose sub-assembly from the No. 6 fuel tank breather tube.


Hide 77217C 20.REMOVE NO. 2 FUEL TANK FILLER PIPE SUPPORT

a.
A311725

Disengage the clamp to remove the No. 2 fuel tank filler pipe support from the fuel tank filler pipe assembly.


Hide 77216A 21.REMOVE NO. 1 FUEL TANK FILLER PIPE SUPPORT

a.
A311726

Remove the No. 1 fuel tank filler pipe support from the fuel tank filler pipe assembly.


Hide 77218A 22.REMOVE NO. 3 FUEL TANK FILLER PIPE SUPPORT

a.
A311727

Disengage the clamp to remove the No. 3 fuel tank filler pipe support from the fuel tank filler pipe assembly.