Home › Engine / Hybrid System › 1NZ-FE ENGINE CONTROL › THROTTLE BODY › 2016.07–2016.10
RM30M0E _51 Engine / Hybrid System _017071 1NZ-FE ENGINE CONTROL _0091206 THROTTLE BODY A

1NZ-FE ENGINE CONTROL  THROTTLE BODY  INSTALLATION  


PROCEDURE

Hide 22030 1.INSTALL THROTTLE BODY WITH MOTOR ASSEMBLY

a.

Install a new throttle body gasket to the intake manifold.


b.

Install the throttle body with motor assembly to the intake manifold with the bolt and 3 nuts.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)

NOTICE:

If a component has been dropped or subjected to a strong impact, replace the throttle body with motor assembly.



c.

Install the wire harness clamp bracket to the throttle body with motor assembly with the nut.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


d.

Connect the throttle body with motor assembly connector.


e.

Engage the clamp to connect the wire harness to the wire harness clamp bracket.


Hide 16261 2.CONNECT WATER BY-PASS HOSE

a.

Connect the water by-pass hose to the throttle body with motor assembly with the hose clip.


Hide 16264 3.CONNECT NO. 2 WATER BY-PASS HOSE

a.

Connect the No. 2 water by-pass hose to the throttle body with motor assembly with the hose clip.


Hide 16522 4.INSTALL WATER FILLER BRACKET

a.

Install the water filler bracket to the throttle body with motor assembly with the 2 nuts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 17735 5.INSTALL AIR CLEANER CAP WITH NO. 1 AIR CLEANER HOSE

a.

Engage the 2 guides to install the air cleaner cap with No. 1 air cleaner hose to the air cleaner case sub-assembly and throttle body with motor assembly.


b.

Engage the 2 clamps to secure the air cleaner cap to the air cleaner case sub-assembly.


c.

Connect the No. 1 air cleaner hose to the throttle body with motor assembly and tighten the hose clamp.

Torque:
3.0 N*m (31 kgf*cm, 27 in.*lbf)


d.

Engage the 3 clamps to connect the wire harness to the air cleaner cap and purge VSV.


e.

Connect the purge VSV connector and mass air flow meter connector.


Hide 17341T 6.CONNECT NO. 1 AIR HOSE

a.

Connect the No. 1 air hose to the No. 1 air cleaner hose with the hose clip.


Hide 23820 7.CONNECT FUEL VAPOR FEED HOSE ASSEMBLY

a.

Connect the fuel vapor feed hose assembly to the purge VSV and No. 1 air cleaner hose with the 2 hose clips.


b.

Connect the fuel vapor feed hose assembly to the clamp of the No. 1 air cleaner hose.


Hide 23827A 8.CONNECT NO. 2 FUEL VAPOR FEED HOSE

a.

Connect the No. 2 fuel vapor feed hose to the intake manifold.


Hide 12.PERFORM INITIALIZATION

NOTICE:

Perform the following procedure after replacing the throttle body with motor assembly or any throttle body with motor assembly components. The following procedure should also be performed if the throttle body with motor assembly is cleaned.


a.

Disconnect the cable from the negative (-) battery terminal. Wait at least 60 seconds and reconnect the cable.


b.

Turn the ignition switch to ON without operating the accelerator pedal.

NOTICE:

If the accelerator pedal is operated, perform the above step again.




d.

Start the engine and check that the MIL is not illuminated. After the engine is warmed up, check that the idle speed is within the specified range with the A/C switch off.

Standard idle speed:

650 to 780 rpm


NOTICE:
·

Turn all electrical systems and the A/C off.

·

Inspect the idle speed with the cooling fans off.

·

When checking the idle speed, the transaxle should be in neutral or park.




e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Throttle Sensor Position. Fully depress the accelerator pedal and check that the value is 60% or higher.

Powertrain > Engine and ECT > Data List
Tester Display
Throttle Sensor Position
50003 234 12

f.

Perform a road test and confirm that there are no abnormalities.