1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
51442C
3.REMOVE ENGINE UNDER COVER LH
51441C
4.REMOVE ENGINE UNDER COVER RH
5.DRAIN MANUAL TRANSAXLE OIL
23827A
6.DISCONNECT NO. 2 FUEL VAPOR FEED HOSE
23820
7.DISCONNECT FUEL VAPOR FEED HOSE ASSEMBLY
17735
8.REMOVE AIR CLEANER CAP WITH NO. 1 AIR CLEANER HOSE
17801
9.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
17701
10.REMOVE AIR CLEANER CASE SUB-ASSEMBLY
28800
11.REMOVE BATTERY
74431
12.REMOVE BATTERY TRAY
74410
13.REMOVE BATTERY CARRIER ASSEMBLY
33820B
14.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY
Remove the 2 clips A and 2 washers to disconnect the transmission control cable assembly from the floor shift selecting bellcrank assembly.
Remove the 2 clips B to separate the transmission control cable assembly from the control cable bracket.
82123
15.DISCONNECT NO. 3 ENGINE WIRE
Remove the bolt to disconnect the No. 3 engine wire from the manual transaxle assembly.
Disengage the 2 clamps to separate the No. 3 engine wire from the engine mounting bracket LH.
82121
16.DISCONNECT ENGINE WIRE
Disconnect the connector from the manual transaxle assembly.
Remove the bolt to separate the engine wire from the wire harness clamp bracket.
Disengage the 2 clamps to separate the engine wire from the wire harness clamp brackets.
33524B
17.REMOVE CONTROL CABLE BRACKET
Remove the bolt and wire harness clamp bracket from the control cable bracket.
Remove the 2 bolts and control cable bracket from the manual transaxle assembly.
31470
18.SEPARATE CLUTCH RELEASE CYLINDER ASSEMBLY
Remove the clip and 2 bolts A to separate the clutch release cylinder to flexible hose tube from the manual transaxle assembly.
Remove the 2 bolts B to separate the clutch release cylinder assembly from the manual transaxle assembly.
Suspend the clutch release cylinder assembly with a piece of rope so as not to place stress on the clutch line.
Do not depress the clutch pedal.
58910C
19.REMOVE REAR CONSOLE BOX ASSEMBLY
57533B
20.REMOVE FRONT FLOOR CENTER BRACE
17410
21.REMOVE FRONT EXHAUST PIPE ASSEMBLY
22.REMOVE FRONT DRIVE SHAFT ASSEMBLIES
28100
23.REMOVE STARTER ASSEMBLY
51201
24.REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY
25.SUPPORT ENGINE ASSEMBLY
| *a | Attachment |
| *b | Engine Lifter |
|
Attachment Placement Positions |
Place the height adjustment attachments or plate lift attachments in the positions shown in the illustration and set the engine lifter underneath the engine assembly.
Place the height adjustment attachments or plate lift attachments so that the engine assembly with the manual transaxle assembly is level.
As the engine assembly with the manual transaxle assembly is very heavy, be sure to support it securely.
To prevent deformation of the No. 2 oil pan sub-assembly, never set any attachments against the No. 2 oil pan sub-assembly of the engine assembly.
12321B
26.REMOVE DRIVE SHAFT HEAT INSULATOR SUB-ASSEMBLY
Using a 12 mm deep socket wrench, remove the nut.
Remove the bolt and drive shaft heat insulator sub-assembly from the engine assembly.
12313
27.REMOVE ENGINE MOVING CONTROL ROD BRACKET
Remove the 4 bolts and engine moving control rod bracket from the manual transaxle assembly.
30300
28.REMOVE MANUAL TRANSAXLE ASSEMBLY
Set the transmission jack underneath the manual transaxle assembly.
Secure the manual transaxle assembly to the transmission jack using a suitable adapter, such as a rope or attachment.
Remove the bolt and nut to separate the engine mounting insulator LH from the engine mounting bracket LH.
Turn the bolt while holding the nut.
| *a | Hook |
Remove the 5 bolts.
Disengage the hook to remove the engine mounting insulator LH from the body.
Remove the 4 bolts and engine mounting bracket LH from the manual transaxle assembly.
| *1 | Engine Assembly |
| *2 | Manual Transaxle Assembly |
| *a | Body |
| *b | Tilt 50 mm (1.97 in.) or less |
|
Watch for Interference |
Operate the engine lifter and transmission jack, and slowly tilt the engine assembly with the manual transaxle assembly 50 mm (1.97 in.) or less.
Do not allow the engine assembly and manual transaxle assembly to interfere with the body.
Make sure that the engine assembly is not tilted more than necessary.
Make sure that the wire harness and hoses are not being pulled.
Remove the 7 bolts.
Bolt A: Remove from manual transaxle assembly side
Bolt B: Remove from engine assembly side
| *1 | Clutch Disc Assembly |
| *2 | Clutch Cover Assembly |
| *3 | Input Shaft |
Using the transmission jack, remove the manual transaxle assembly from the engine assembly according to the procedures shown in the illustration.
To prevent damage to the knock pins, do not pry between the manual transaxle assembly and engine assembly.
To prevent damage to the input shaft, do not forcefully shake the manual transaxle assembly.
Move the manual transaxle assembly towards the left side of the vehicle and disengage the input shaft from the clutch disc assembly.
Tilt the manual transaxle assembly and pull the input shaft out from the clutch cover assembly.
Lower the manual transaxle assembly.
29.REMOVE WIRE HARNESS CLAMP BRACKET
Remove the 2 bolts and 2 wire harness clamp brackets from the manual transaxle assembly.
33403K
30.REMOVE SPEEDOMETER DRIVEN HOLE COVER SUB-ASSEMBLY
Remove the bolt and speedometer driven hole cover sub-assembly from the manual transaxle assembly.
Remove the O-ring from the speedometer driven hole cover sub-assembly.